Kenmore 9031 Support Question
Kenmore 9031 Support Question
Find answers below for this question about Kenmore 9031 - 7.3 cu. Ft. Gas Dryer.Need a Kenmore 9031 manual? We have 1 online manual for this item!
Question posted by kittykinstley on February 26th, 2011
New Kenmore Gas Dryer 90311 Drum Will Not Turn, Power Is On.
Control panel indicates dryer is going through cycle but drum is not turning and gas is not heating.
Current Answers
Related Kenmore 9031 Manual Pages
Use and Care Guide - Page 2
I
I
IMPORTANT SAFETY INSTRUCTIONS
Master Protection Agreements
SAFETY MESSAGES
3
Congratulations on making a smart purchase. Your new
IMPORTANT SAFETY INSTRUCTIONS
3-6
Kenmore
Use and Care Guide - Page 4
... I
I In the event of natural gas or LP fuels. Check with controls. • Before the dryer is removed from service or discarded, remove... • Clean lint screen before using the dryer.
• Before use heat to dry articles containing foam rubber or similarly ...be grounded. The plug must be plugged into the dryer if the drum or any servicing unless specifically recommended in this Use ...
Use and Care Guide - Page 5
.../Ducting"
Gas dryers MUST be...power circuit can cause a fire. There is not properly grounded. Do not install nearby heat... item.
Failure to clean any area of this warning can result in fire or death.
The exhaust duct
should have hinged dampers to do so can cause a fire if it collapses or becomes otherwise restricted in any old ducts before installing your new dryer...
Use and Care Guide - Page 7
... system that illuminates when the dryer door is open and turns off when the door is closed. CYCLE MODIFIERS
Adjust the cycle defaults such as temperature and dryness level with a light that reduce airflow from the dryer. Power Cord Location (Gas Models)
Terminal Block Access Panel (Electric Models)
ULTRA-CAPACITY STAINLESS STEEL DRUM WITH DRUM LIGHT
The ultra-large stainless...
Use and Care Guide - Page 8
...gas connections, and exhaust requirements are installing your dryer in front of the dryer to the section Special Requirements for wall, door, or floor moldings that you are provided on Page 12.
ft.
*Gas... in a garage, place the
dryer at least 21 in. (53.3 cm) in a manufactured or mobile home, please refer to open ) 126 lb. (57.2 kg) IEC 7.3 cu. IMPORTANT: Read all governing codes...
Use and Care Guide - Page 10
... be used where lengths are less than 20 ft. (6.1 m). Failure to do so can result in fire, explosion, or death.
• DO NOT attempt any pressure testing of the gas supply. Electrical Requirements for use with the National Fuel Gas Code ANSI Z223.1. I
I
GAS REQUIREMENTS CONNECTING GAS DRYERS
(GAS MODELS ONLY)
|
VV/-_I-II_III_Ik._"
TO reduce the...
Use and Care Guide - Page 11
... only a new stainless steel flexible connector and a new AGA-certified connector. Failure to do so can result in fire, explosion, or death. • Gas dryers MUST exhaust to...dryer is to the laundry room is
turned OFF and the dryer is configured from the gas fitting at an elevation above 10,000 feet, it must be installed within 6 ft. (1.8 m) of the dryer. O Make sure that the type of gas...
Use and Care Guide - Page 12
...dryer. Heating elements are available for field installation in dryers which are to be fused on the rating plate.
If over 15 ft... is required for all new construction after January 1, 1996. A 4-wire connection must conform to dryer is 15 ft. (4.5 m) or less...or death.
• The power cord (pigtail) connection between wall receptacle and dryer terminal block IS NOT supplied ...
Use and Care Guide - Page 13
Wire color indicated on new construction after January 1, 1996.
• A UL-listed strain relief is required. ° Use a 30-amp, 240-volt, 4-wire, UL-listed power
° Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through -hole.
tral"" Hot...
Use and Care Guide - Page 16
... to follow these instructions can be a level, solid surface. O Reinstall the door latch with the floor.
NOTE: If you are in the open holes. O Carefully turn the leveling feet.
Make sure that the dryer provides optimal drying performance, it must be fully retracted. Reattach the door to support the weight of the...
Use and Care Guide - Page 17
... per year. NOTE: A 3-wire connection
is in its final location, recheck the dryer to be plugged in ?
Testing Dryer Heating GAS MODELS
O Close the dryer door. O Press the Power button to Normal drying cycle. O Press the Cycle Selector Knob to turn off before using the dryer. When the dryer starts, the igniter should be checked for obstructions and blockages. O Press the...
Use and Care Guide - Page 18
... DRY) remaining and start tumbling. NOTE: Pressing the Power button during a cycle wilt cancel that cycle will turn off automatically.
® OPTION BUTTONS
The option buttons allow you to select additional cycle options.
CONTROL PANEL FEATURES
iii Iz
O POWER (On/Off) BUTTON
Press to turn the dryer ON. To pause the cycle at any load settings wilt be locked or unlocked...
Use and Care Guide - Page 19
... THE DRYER Load the dryer with the wet laundry from the washer. This can be done using the options buttons as shown on .
If the cycle is on the dryer.
O TURN ON THE DRYER Press the POWER button to page 18.
O SELECT CYCLE OPTIONS Cycle options can be added using the cycle modifier buttons as shown on all cycles.
Refer to turn on...
Use and Care Guide - Page 22
... CHECK VENT duct blockage sensing system detects and alerts you to set , the Control Lock indicator will uminate. When the dryer is turned on the conditions of the drying cycle is selected, the display will indicate the default time for maximum efficiency.
If this light blinks, it indicates that reduce exhaust flow from changing settings while the...
Use and Care Guide - Page 24
...controls can 't be turned off , the power button will tumble the clothes for a few seconds every few minutes without heat. NOTE: * Do NOT use any cycle but the controls will be turned on the rear wall just above the drum. CONTROL... CONTROL LOCK button for 90 minutes after using the RACK DRY cycle.
24
I
I
CYCLE OPTIONS AND SPECIAL FEATURES 'Your dryer features several additional cycle ...
Use and Care Guide - Page 25
... warning can build up on the control panel will blink before every cycle to avoid the risk of fire, electric shock, or injury to the dryer that could damage the door seal....by damaged, restricted, or otherwise inadequate exhaust systems is not covered by the dryer warranty. The CHECK VENT indicator signals a serious reduction in drying performance occurs, check ductwork for damage or ...
Use and Care Guide - Page 26
... is blown, circuit breaker has tripped, or power outage has occurred. Partial blockage of static electricity. Greasy or dirty spots on dried clothes could be displayed.
Drying synthetics, permanent press, or synthetic blends. Overdrying a load of laundry can be checked/cleaned immediately. Dryer does not heat Check if...
Then... Verify that clothes are working...
Use and Care Guide - Page 27
... configured and free of load you are drying a very small load, add a few extra items to dry. Heat settings, load size, or dampness of a consistent size. Clothes take longer to ensure proper tumbling action. Dryer controls are not blocked, jammed, or damaged. Lint filter needs to be necessary to dry. Light items in...
Use and Care Guide - Page 28
...pockets. Turn off the dryer and call for drying.
Remove the lint from clothes that produce high amounts of laundry can..., or use SENSOR DRY cycles.
Then,.. Display shows error code TEl or TE2 Check if... Laundry not sorted properly.
Dryer is dirty or clogged....heat setting and/or the RACK DRY, If available.
With some fabrics will shrink when dried in dryer too long after cycle ...
Use and Care Guide - Page 29
..., disconnect them from all power, water, or gas lines and from Natural Gas
(NG)to do so can cause serious accidents. Do not use the stacking kit with a gas dryer in place.
29
I
... D2617002(White) D2617008(Ginger) D2617009(ChiliPepper)
Use the side vent kit for changingthe dryer gas connections from drain ing or venting connections. Failure to follow this warning can result in...
Similar Questions
How Many Btu's Is My Kenmore Gas Dryer Model 11070702990
how many btu's is my Kenmore gas dryer model 11070702990
how many btu's is my Kenmore gas dryer model 11070702990
(Posted by donald12eck 6 years ago)
Diagnostic Testing Mode On He2 Dryer
How do u enter the diagnostic testing mode on a Kenmore HE2 electric dryer?
How do u enter the diagnostic testing mode on a Kenmore HE2 electric dryer?
(Posted by dawnmrepose 9 years ago)
Kenmore Dryer I
I have aquestion about a Kenmore dryer I juts purchased that has a flaw in it. who do I talk to?
I have aquestion about a Kenmore dryer I juts purchased that has a flaw in it. who do I talk to?
(Posted by richardlindalarson 11 years ago)
I Have A Kenmore 600 Series Dryer And I Am Going From A 4 Prond Cord To A 3 Pron
do i need to attach a 10g wire from ground screw to center white neutral wire
do i need to attach a 10g wire from ground screw to center white neutral wire
(Posted by dentonkola 11 years ago)