Husqvarna MZ 6128 Support Question
Husqvarna MZ 6128 Support Question
Find answers below for this question about Husqvarna MZ 6128.Need a Husqvarna MZ 6128 manual? We have 2 online manuals for this item!
Question posted by tcar011458 on September 1st, 2020
Pto Switch
I have MZ 61 & MZ 48. 61 PTO would not engage. Took PTO switch panel off terminal with blue wire was slightly melted. So to troubleshoot I took switch out of 48 and put into 61. still did not work. put switch back in 48 and it would not work. Ohmed out both clutches and got 2.2 & 3.3. It is my understanding that they should be between 2 & 4, so they should be good unless I got wrong information. Bought new switches and fixed 48. Can jump between purple wire and blue wire on PTO switch wiring harness and blades will run. Can you tell me what I am missing? I have tried to find wiring diagram for PTO switch harness so I can see what other wires go to but have not been successful. Thanks in advance for your help.
Current Answers
Answer #1: Posted by hzplj9 on September 1st, 2020 2:05 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,873,500
Member since:
June 25th, 2012 Points: 4,873,500
Go to this link and download the manual. Page 51 of the PDF of 64 pages gives you a circuit diagram of the wiring of the machine. If you check your wiring compares to this then you should be OK.
https://www.manualslib.com/manual/74127/Husqvarna-115-312526r1.html#product-MZ6128
Hope that helps, if so please mark as helpful thanks.
Related Husqvarna MZ 6128 Manual Pages
Owners Manual - Page 3
... Hour Meter 19 Tracking 19 Parking Brake 20 Blade Switch 20 Ignition Switch 20 Fuses 21 Cutting Height Adjuster 22 Fuel Shut...Pump Belt 39 V-belts 39 Cutting Blades 40 Adjusting the Mower Deck 41
Leveling deck 41 Anti-scalp rollers 42 Caster ...46 Purging Procedures 47 TROUBLESHOOTING GUIDE 48 STORAGE 50 Winter Storage 50 Service 50 WIRING DIAGRAMS 51 TECHNICAL DATA 52 Torque ...
Owners Manual - Page 5
A control panel that service and repair work are subject to change without obstacles such as stones, tree stumps, etc.... operation, maintenance, and repairs must be sure to give the operator's manual to your dealer for more information.
Lawn mowers and all who are provided with special accessories provided by persons familiar with these instructions and common sense. This manual...
Owners Manual - Page 14
...8226; Ensure that the equipment is in safe working condition.
• Never tamper with manufacturer's recommended parts, when necessary.
• Mower blades are considered to cool before restarting.
...the engine running the engine with defective or unmounted protective plates, protective cowlings, safety switches, or other debris buildup. Repair, if necessary, before storing.
• If ...
Owners Manual - Page 20
... brake is found on the control panel and is used to start the engine.
The mower blades are disengaged when the knob is placed on the left of the machine. Ignition switch 20
8058-044 8058-043 8058-043
Parking brake
Blade Switch
To engage the mower deck, pull the blade switch knob out. IMPORTANT INFORMATION The...
Owners Manual - Page 21
Ignition switch -
They are located on the left hand side of the machine. RUN position For using "accessory", turn the... pin fuses type as used in automobiles. Fuses are two fuses with ratings and functions:
1. 20 A, Primary fuse
2. 7.5 A, Mower deck coupling
Ignition switch - accessory
Fuses
8066-005
8011-420
21 CONTROLS
Release the key to the RUN position when the engine has started.
Owners Manual - Page 25
...; Perform the daily maintenance before starting
8058-044
Starting the Engine
1.
Activate the parking brake. Set mower deck to the transport position by
locking the lift pedal fully forward. 3. Activate parking brake before the... in the locked
(outer) neutral position. The blade switch for engaging the mower blades must be depressed.
2. The parking brake must be on the seat. 2.
Owners Manual - Page 26
OPERATION
4. Move the throttle to the locked (outer) neutral position. Disengage the mower blades by depressing the blade switch.
5. Place controls in neutral position
80661-012
Set the throttle
80658-050
26 Press the control for disengaging the mower deck
8058-043
6. Move the steering controls outward to the middle position.
Owners Manual - Page 29
... Select the cutting height by pulling out the blade switch.
6. Move throttle control to the neutral position (N). Cutting height selection
5. Engage the mower deck by setting the cutting height pin into the ... is running, any attempt by the rotating blades.
8058-044
WARNING! Make sure the work area is free from objects that no one is equipped with an operator presence system. ...
Owners Manual - Page 31
If the engine has been worked hard, allow it to idle at least 60 seconds to the minimum position (tortoise symbol). Move the steering controls outward.
6. Raise the mower deck by depressing the blade switch.
8058-046
Disengage the mower deck and move throttle to the stop
8061-012
31 Move the throttle to the...
Owners Manual - Page 32
... that the deck is cleaned more evenly distributed over 6" (15 cm) in height should be raised into the soft lawn, clumps build, and the grass clippings fasten under the cowling.
• Hose the mower deck underside with water after moderate growth.
• For best cutting performance, grass over the mown area. The...
Owners Manual - Page 35
...adjust the mower deck ...Engage the parking brake. • Place the Blade-switch in the disengaged position. • Turn the ignition switch... to "OFF" position and remove the key. • Make sure the blades and all moving parts have completely stopped. • Disconnect the spark plug wire from all spark plugs and place the wire...
Owners Manual - Page 36
... bands, rings, etc.
Positive terminal must be connected first to "leak" power. 1. maintenance
Battery
Your mower is not necessary. Always wear eye protection when around batteries. Coat terminals with wire brush until shiny. 5. Carefully... Install new battery with plain water and dry. 4. FULL CHARGE -
20 min. 35 min. 48 min. 90 min. 45 min. 75 min. 95 min. 180 min. 65 min. 115 min...
Owners Manual - Page 37
... start the engine when one of these conditions is on the lever, links, or switch belonging to the parking brake. specified tires.
maintenance
Safety System
This machine is sufficient ... works by foam filled tires will stop. Faulty adjustment results in the outer, locked neutral position.
3.
Make daily inspections to 15 psi / 103 kPa / 1 bar. The mower deck is not engaged and...
Owners Manual - Page 48
... circuit.
Problem Engine will not start. troubleshooting guide
Cause
• Blade switch is engaged. • Steering controls are not locked...8226; Fouled spark plugs. • Carburetor incorrectly adjusted.
48 Starter does not turn the engine over. See Safety
System... jet. • Clogged ventilation valve on the battery terminal cable
connections. • Fuse blown. • Ignition...
Owners Manual - Page 49
troubleshooting guide
Problem Machine vibrates. Engine overheats. Battery not charging. Machine moves slowly, unevenly, or not at all.
• Poor contact with battery terminal cable connectors.
...mower deck has come loose, from the cable contact.
• The fuse has blown.
Mower deck not engaging.
• Drive belt for the electromagnetic coupling has loosened.
• The blade switch...
Owners Manual - Page 51
...
BLK
BLK
ACCESSORY
BLK
OUTLET
ENGINE GROUND PTO IN OFF POSITION
RIGHT MOTION CONTROL LEVER
YEL
LEFT MOTION CONTROL LEVER
YEL BRN
BRN
GRN
BRAKE SWITCH
GRN
WHT
WHT
YEL
TO ENGINE PIGTAIL
PUR GRY
RED/BLK
RED/BLK
B SA
L
Y
MG
20 AMP
RED
SEAT SW. WIRING DIAGRAM
51
SOLENOID YEL
NOTES: 1. SEAT...
Owners Manual - Page 57
... engine. 6. Parking brake functionality. Application areas for the mower deck. Certified:
57 Engaging the blades. 12. Check that there is in the normal position. 4. Fill with fuel and open the fuel shut off valve. 8. Effects of all wheels to both wheels. 10. Safety switch in the steering controls.
SERVICE JOURNAL
Action
Delivery Service...
Parts Manual - Page 7
...539 990053 2 WASHER ¼ INT TOOTH LK 47.. 539 990188 2 WASHER 5/16 SAE FLT 48.. 539 109554 2 WASHER ½ FLT 49.. 539 109562 1 WASHER 3/8 x ¾ 50... 1 WASHER ½" BELLEVILLE 52.. 539 104763 4 RETAINER, U TYPE 5/16-18 NOT SHOWN
576 413201 1 PIGTAIL, MZ
7 QTY.
DESCRIPTION 1.. 575 608801 1 PLATE, ENGINE w/ DECAL 2.. 574 846402 1 PLATE, IDLER SUPPORT 3.. 574 811001...
Parts Manual - Page 11
...WIRE TIE
11 IGNITION
ITEM PART NO. DESCRIPTION
1.. 574 841204 1 PLATE, CONSOLE, BLK 2.. 539 112438 1 CABLE, THROTTLE 3.. 539 131627 1 SWITCH, PTO 10 AMP 4.. 574 455401 1 SWITCH, IGNITION 5.. 539 113792 1 SWITCH, BRAKE 6.. 532 109553 2 SWITCH...1 CAP, IGNITION SWITCH NUT 18.. 539 107765 1 HOSE, FUEL 19.. 539 932956 1 HOSE, FUEL 10" 20.. 576 660602 1 HOSE 3/16 VAPOR 48" 21.. 575 ...
Parts Manual - Page 21
MOWER DECK / CUTTING DECK
ITEM PART NO. QTY. DESCRIPTION
1.. 581 505401 1 DECK w/ SAFETY DECALS 2.. 539 104335 1 BELT, DECK 3.. 510 417901 3 BLADE, 21" 4.. 539 112170 3 HOUSING ASSEMBLY ...SPRING 44.. 539 102243 1 WASHER, SUPPORT 45.. 539 990550 1 WASHER ½ STD FLT 46.. 539 107520 3 WASHER-SPACER 47.. 539 104763 8 RETAINER, U TYPE 5/16-18 48.. 539 976998 1 ZERK
21 QTY.
Similar Questions
When Is The Interlocking Clutch Cable Switch Located On Mz54
(Posted by Dsarvis58 2 years ago)
What Is A 2012 Husqvarna Hu 775l Lawn Mower In Very Good Condition Worth ?
What is a 2012 Husqvarna HU 775L lawn mower in Very good condition worth ?
What is a 2012 Husqvarna HU 775L lawn mower in Very good condition worth ?
(Posted by kpcastles 7 years ago)
The Mower Will Start The Blades Will Turn But It Wont Drive
(Posted by erickmorris89 8 years ago)
Husqvarna Mz 6128 20 Amp Fuse Keeps Blowing
Every time you would turn the Key the 20 Amp fuse blows. have replaced the switch and have check all...
Every time you would turn the Key the 20 Amp fuse blows. have replaced the switch and have check all...
(Posted by JonathanWilliams2961 9 years ago)
My Husqvarnarz4623 Lawn Mower
My husqvarna lawn mower will not start. It wont even try to turn over or click.
My husqvarna lawn mower will not start. It wont even try to turn over or click.
(Posted by teresaandbryancates 9 years ago)