Husqvarna K 3000 Vac Support Question
Husqvarna K 3000 Vac Support Question
Find answers below for this question about Husqvarna K 3000 Vac.Need a Husqvarna K 3000 Vac manual? We have 1 online manual for this item!
Question posted by christinebailey on July 22nd, 2015
How To Replace Spring
There is a small spring under the air filter on the 775ex husquvarna mower. The spring attached to silver fixed piece and assuming to the black piece that moves but how?
Current Answers
Answer #1: Posted by hzplj9 on July 26th, 2015 1:18 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,871,500
Member since:
June 25th, 2012 Points: 4,871,500
I have attached a link to your mower user guide.
It doe snot show the spring you mention but from a view it is part of the carburettor assembly. This would requires a parts list to identify its location so I would suggest asking at your local mower repair agents who could well give you the info. You could also check out U-tube with a model search and someone out there has already solved your dilemma.
Related Husqvarna K 3000 Vac Manual Pages
Owners Manual - Page 3
... blade 15 Guard for the blade 15 STARTING AND STOPPING Before starting 16 Starting 16 Stopping 16 MAINTENANCE General 17 Cleaning 17 Electrical Feed 17 Replacing the carbon brushes 17 Bevel gear 18 Checking the drive shaft and flange washers ....... 18 Checking water connection with flow limiter ......... 18 Daily...
Owners Manual - Page 7
...the cutting blade stop .
• Check that the power switch and power switch lock move freely and that it .
contact your nearest
service agent.
The engine starts to be ...All servicing and repair work properly.
• A defective power switch should be replaced by two independent return springs.
machine is released both the power switch and power switch lock are reset. ...
Owners Manual - Page 9
.... Do not use the machine so that the cord and extension cord are
standing firmly. Keep cord away from heat, oli, charp edges or moving parts.
Do not start to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Electrical safety
• Power tool plugs must
always...
Owners Manual - Page 10
...reduce dust-related hazards.
• Remain at a distance from moving parts. Power tools are easier to operate the power tool. ...by a qualified repair person unsing only identical replacement parts. Use of parts and any way from the ...situations.
• Dress properly. A wrench or a key left attached to a rotating part of dust extraction and collection facilities, ensure that...
Owners Manual - Page 11
...Check that prevents total breakage at a lower speed rating than that it lightly with attachments.Such cutting blades must be of the recommended type for the same or higher ... blades for . A cutting blade may burst
! and cause injury to be used .
Otherwise replace the blade.
"Reinforced blades" are often most economical.
A cutting blade's performance is used on...
Owners Manual - Page 12
... metals. Working with the cutting blade fitted.
Diamond blades
WARNING!
Diamond blades get very hot
! A heated blade can cause imbalance and result in the air for hard materials such as brick and asphalt.
12 -
Always use and stored carefully.
• Special care should be removed from the cut every 30...
Owners Manual - Page 13
...is not in line with the machine running at maximum speed.
• Move the blade slowly forwards and backwards to work piece. Do not pull the power cutter to one side, this can cause ...task that the cut at maximum speed.
• Start cutting smoothly, allowing the machine to achieve a small contact area between the blade and
English - 13 Hold it will happen, and so that
you feel ...
Owners Manual - Page 14
..."Basic rules" and "Jamming/rotation", here below.)
Pinching/rotation
If the cut is moving it can be thrown from the work piece. • Take care when inserting the blade in an existing cut. • ...the blade
as shown in a firm grip with the upper quadrant of the work piece or anything
else that you
understand what causes kickback and
that can lead to avoid kickback
WARNING...
Owners Manual - Page 15
...locking button on the rear of the machine.
The button is spring-loaded and is reset when button is mounted on the power ... collected up by holding the blade is flush with the work piece. When a diamond blade is released. When the blade is mounted on...that indicates the axleís direction of rotation that the blade is replaced with a new one, check the flange washers and the ...
Owners Manual - Page 17
...the springs and tighten the cable.
• New carbon brushes must be carried out with the rear handle facing upwards. The carbon brushes should be replaced when the brushes are replaced.
... a month.
The cleaning reduces the risk for approximately 40 minutes while idling.
Cooling air which is not equipped with clean water.
Now lift up inside of the
machine.
...
Owners Manual - Page 18
... total. The gear housing should contain 90 g of grease in total. Do not use different dimensions of the cutting blade. 6 Check and clean the cooling air openings. 7 Check that the threads on the drive axle.
CAUTION! English
MAINTENANCE
Bevel gear
The grease in the gear housing should be filled completely...
Similar Questions
Wont Drive Forward Or Back Found Broken Spring Attached To Chasey
(Posted by washy2 1 year ago)
Surging Problem With Husqvarna Yth20k42,kohler 7000
I am trying to access the govenor, which apparently is near the carburetor.The fly-wheel cover has f...
I am trying to access the govenor, which apparently is near the carburetor.The fly-wheel cover has f...
(Posted by castbankes 2 years ago)
Fuses
How do you remove the dash on Model YTH21K46 to replace fuses?
How do you remove the dash on Model YTH21K46 to replace fuses?
(Posted by lavondalang 9 years ago)
Mower Will Not Go Into Gear
how do u replace a motion drive belt on a yth2042
how do u replace a motion drive belt on a yth2042
(Posted by lindakbrown 9 years ago)
Changing Blade On Husqvarna K3000 Vac
I can't get the blade off to change to a new one.... Please help
I can't get the blade off to change to a new one.... Please help
(Posted by jwhall94 9 years ago)