Husqvarna 372 XP Support Question
Husqvarna 372 XP Support Question
Find answers below for this question about Husqvarna 372 XP.Need a Husqvarna 372 XP manual? We have 2 online manuals for this item!
Question posted by brwilson1 on December 22nd, 2021
Top Cover Bolt Threads
I can't screw the top down on my husky 372xp. It is missing the threads. Are they replaceable?
Current Answers
Answer #1: Posted by SonuKumar on December 23rd, 2021 3:46 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
https://www.ereplacementparts.com/husqvarna-372xp-xpxtorq-chain-saw-parts-c-114486_114487_290347.html
https://www.diyspareparts.com/parts/husqvarna/fits/husqvarna-372xp-chainsaw/
https://www.ebay.com/sch/Husqvarna-372xp-Parts/85915/bn_7023394932/i.html
yes possible to replace
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Husqvarna 372 XP Manual Pages
Owners Manual - Page 1
Operator's manual
365 SPECIAL 372 XP 372 XPG
Please read the operator's manual carefully and make sure you understand the instructions before using the machine. English
Owners Manual - Page 5
...the construction of this may be necessary. In 1956, the first motor driven lawn mowers appeared, followed by chain saws in the world of products without prior notice. Think...building and construction industry. Thank you access to modify the design and appearance of forest and garden products, with repairs and service whenever this operator′s manual as our highest priority. ...
Owners Manual - Page 6
...
16 Bumper spike 17 Chain catcher 18 Clutch cover 19 Rear handle with right hand guard 20 Throttle control 21 Throttle lockout 22 Decompression valve 23 Combination spanner 24 Chain tensioning screw 25 Operator's manual 26 Transport guard 27 Switch for heated handle (Model 372 XPG) 28 Information and warning decal 29 Product...
Owners Manual - Page 7
...chain increases the risk of kickback!
English - 7 Under no circumstances may not cover damage or
liability caused by trained and qualified specialists. Your
warranty may
...8226; Please read and
understand the contents of this
operator's manual. WARNING! authorized accessories or replacement
parts.
Always wear protective glasses or a face visor to the eyes. A chain saw ...
Owners Manual - Page 8
... accidents can provide information about the use of movement.
See instructions under the heading Checking, maintaining and servicing chain saw . Work is not possible to cover every conceivable situation you with
! Machine′s safety equipment
In this section the machine's safety features and their function are available.
• Protective goggles or...
Owners Manual - Page 14
...depth gauge tool. Tighten the chain until it round freely by tightening the chain tensioning screw using the combination spanner. to find out where it is correct when you ...package for your model.
14 -
Tension the chain as tightly as you should be replaced. The risk of the cutting teeth is what? We recommend that protrudes through the ...hold the clutch cover/chain brake.
Owners Manual - Page 17
... Note: If clutch cover is correctly located in the groove in disengaged position by turning the chain tensioning screw clockwise using the combination ... remove the clutch cover (chain brake). When fitting a new chain, the chain tension has to remove, replace bar nuts, engage...edge of the chain fit correctly over the bar bolts. Fitting the bar and chain
ASSEMBLY
Tension the chain by...
Owners Manual - Page 20
... choke control in order to reduce the pressure in the choke control as soon as for starting attempts. Do not pull the starter cord all covers are fitted correctly. Immediately press and release the throttle when the engine starts. The correct choke/start a chain saw . Hold the chain saw on...
Owners Manual - Page 21
... handed, should be activated when starting. This method is very dangerous because you may lose control of the saw unless the bar, chain and all covers are fitted correctly. The engine is no risk of the
! Do not drop start. Exhaust fumes can represent a
health risk.
• Never start the...
Owners Manual - Page 23
... mild, but it for any distance.
7 When you put the chain saw on the ground, lock the saw chain using the chain brake. the clutch cover causing the chain to
jam. Never use the chain saw one piece at a time. Have control over the workpiece. General rules
1 If you . Wrap your...
Owners Manual - Page 30
... and the cylinder cover fitted. L = Low speed jet
- T = Idle adjustment screw
T
H
• The L and H-jets are adjusted during the first 10 hours. If the T-screw is turned clockwise this...be carried out by a qualified person. First adjust the Ljet, then the idling screw T and then the H-jet.
Conditions
• Before any adjustments are achieved. Any maintenance ...
Owners Manual - Page 31
... to make minor adjustments to the high speed jet. It should contact a mechanic with the T-screw. WARNING! When test run at idle. CAUTION! If the Hjet is adjusted at the same time... to the rpm when the chain starts to rotate.
This is securely anchored to the clutch cover. CAUTION! When working at most half a turn counterclockwise until the chain starts to rotate.
To...
Owners Manual - Page 35
... Lubricate the recoil spring with the pawls.
• Fit and tighten the screws that the spark plug is 0.020 inch (0.5 mm).
Use of air &#...plug first before taking off the air filter cover.
When refitting make sure that the electrode gap...light oil. Contact your dealer for a long time cannot be replaced. Then slowly release the starter cord so that the recoil ...
Owners Manual - Page 36
...guide plate. 3 Fins on the flywheel. 4 Cooling fins on the cylinder. 5 Cylinder cover (directs cold air over the cylinder).
5
The clutch drum has a needle bearing on the output shaft.... needle bearing must be lubricated regularly (once a
week). Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow.
2
1
Clean ...
Owners Manual - Page 37
... the following : All air to increase the temperature these changes must be reversed before the machine is used in cold weather or powder snow, a special cover is available, which is a risk of the carburettor can occur when using the machine in the carburetor.
It is off in position "0", supplies current to...
Owners Manual - Page 39
...4-21 0,89/0,42 Automatic
13,2/6,0
15"/38 15-28"/38-71 14-27"/35-69 3/8" /9,52 0,058/1,5 Rim/7 20,7
372 XP
4,31/70,7 1,97/50 1,42/36 2700 3,9/ 5,3 @ 9600
NGK BPMR 7A/ Champion RCJ 7Y 0,02/0,5
1,63/0,77 ...4-21 0,89/0,42 Automatic
13,4/6,1
15"/38 15-28"/38-71 14-27"/35-69 3/8" /9,52 0,058/1,5 Rim/7 21,4
372 XPG
4,31/70,7 1,97/50 1,42/36 2700 3,9/ 5,3 @ 9600
NGK BPMR 7A/ Champion RCJ 7Y 0,02/0,5
1,63...
Owners Manual - Page 41
...
The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your small nonroad engine for... on the date small nonroad engine is under warranty. WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or replacement of two years. WARRANTY COMMENCEMENT DATE
The warranty period begins on...
Owners Manual - Page 42
... STATEMENT
EMISSION CONTROL WARRANTY PARTS LIST
1 Carburetor and internal parts 2 Intake pipe, airfilter holder and carburetor bolts. 3 Airfilter and fuelfilter covered up to maintenance
schedule. 4 Spark Plug, covered up to maintenance schedule 5 Ignition Module 6 Muffler with catalytic converter
MAINTENANCE STATEMENT
The owner is responsible for...
Parts List - Page 5
...
581 10 07-01 CARBURETTOR
2
503 11 75-01 SCREW
3
522 92 35-01 PUMP COVER
4
503 11 72-01 GASKET PUMP
5
544 89 72-01 DIAPHRAGM PUMP
6
501 46 87-01 SCREW
7
504 79 07-01 LEVER
9
501 66 61-01...503 63 58-01 DIAPHRAGM ASSY
41
505 31 67-02 COVER
42
503 10 87-01 SCREW
43
502 52 92-01 GASKET KIT
44
577 69 97-01 CHECK VALVE ASSY
372XP X-TORQ, 2013-09
Remark Walbro RWJ-4B
Set of gaskets...
Parts List - Page 17
...BOLT
3
501 27 08-01 GUIDE BUSHING
4
530 02 61-19 CHECK VALVE
5
537 40 35-01 FILTER
6
503 96 70-01 BUSHING
7
503 75 18-01 PIN KNEE-JOINT
8
501 27 08-01 GUIDE BUSHING
9
503 21 28-10 SCREW...SCREW
13
503 62 72-01 GASKET CRANKCASE
14
503 85 73-01 COVER...01 STÖTTA FÖRGASARE
38
537 09 54-01 GROMMET
372XP X-TORQ, 2013-09
Remark
Qty Kit 1 11 11 11 11 11 11 11 1 1 1...
Similar Questions
Spark Plug Females Thread On St 227p
Factory plug is a Torch F6RTC, I need to tap the female thread, what is the tap size?
Factory plug is a Torch F6RTC, I need to tap the female thread, what is the tap size?
(Posted by craigmcneil660 4 years ago)
No Spark No Start
Have a Husqvarna riding lawn mower that won't start, there's no spark even after replacing spark plu...
Have a Husqvarna riding lawn mower that won't start, there's no spark even after replacing spark plu...
(Posted by hipolitomary005 6 years ago)
Muffler Bolts,k970
Having trouble with muffler bolts coming loose on Husqvarna K970 concrete saws. Do you know the torq...
Having trouble with muffler bolts coming loose on Husqvarna K970 concrete saws. Do you know the torq...
(Posted by denniswalters 7 years ago)
Need Starter Cover Screw That Attaches Brake On Husqvarna 372 Xp
(Posted by Gmpm511 8 years ago)
Drve Sprocket
my older 372 xp recently had a crank kit and seal rebuild ( about 10 cord ago) it appears to have fa...
my older 372 xp recently had a crank kit and seal rebuild ( about 10 cord ago) it appears to have fa...
(Posted by jamesstrout 11 years ago)