Hunter 90064 Support Question

Find answers below for this question about Hunter 90064.
Need a Hunter 90064 manual? We have 1 online manual for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by larrydameron597 on September 10th, 2020

Hunter Ellipses Lightbulb Removal

The person who posted this question about this Hunter product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by techyagent on September 10th, 2020 5:18 AM

This answer was accepted by the poster of the original question.

techyagent

Member since:
June 17th, 2014

Points: 4,799,780

1,100
points

This is one of the easiest units to replace light bulbs, which makes it great. It doesn't require unscrewing. Simply push the glass up (detaches from hinge), and slide forward approximately .5"; then it'll come right off. It uses a hinge/spring loaded removable cover instead of screws.

Thanks

Techygirl

Related Hunter 90064 Manual Pages

Owner's Manual - Page 1

Owner's Manual - Page 2

...To avoid motor bearing damage and noisy/unbalanced impellers, keep drywall spray, construction dust, etc. Gently vacuum fan, motor and interior of the housing or insert a screwdriver into wall(s) or ceiling, do not damage... over a tub or shower, it can be connected to tab) and twist screwdriver. To remove motor plate, find the single tab on the side of housing. COOKING AREA Do Not Install...

Owner's Manual - Page 3

... 1-888-830-1326 for replacements. Not Included. Before Installation 1 30 20 O FF O FF Tools Needed. (Not supplied) Estimated assembly time: 30 to 60 minutes NOTE: Remove all the parts. x5 A *B *C 3/8" Cable Connector x2 I 30 30 E O FF O FF 20 30 O FF 30 Turn off the power source. 3 41722-01 09/09/2011...

Owner's Manual - Page 4

3 4 H E Remove the motor/blower from the housing. 5 Remove packing material. 6 Remove the pre-loaded screw tip covers. 7 G Back out the pre-loaded screw tips until flush with the side of the housing. 8 F Remove the wiring cover screw. 4 41722-01 09/09/2011 Remove the wiring cover.

Owner's Manual - Page 6

... Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC In) Connect wires as shown. ...

Owner's Manual - Page 9

Pull wires through the strain relief. B17 Attach the rails onto the screws. B18 Tighten screws. B19 Fan Motor Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black...

Owner's Manual - Page 11

B27 ON OFF Test the motor. accessible from above C11 EXISTING FAN NO EXISTING FAN OR Remove an existing fan and check to make sure the opening is large enough to attach grille. B28 Go to step E1 on the power source. If the motor ...

Owner's Manual - Page 14

... plate screw. Make sure the wires are inside the box or under the wiring cover plate. C22 Fan Motor Night Light Light Black 2 Pin White 3 Pin White Red Night Light Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In...

Owner's Manual - Page 15

Test the motor. accessible only from below D11 EXISTING FAN D12 E Remove an existing fan and check to make sure the opening is large enough to step E1 OFF on the power source. If the motor does not run, check ...

Owner's Manual - Page 16

D15 D14 2 1 Attach existing ducting to be purchased. E Screw pre-loaded screws into joist or framing. D16 Fan Motor Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black...

Owner's Manual - Page 18

... plugs as shown, and screw into place. 18 41722-01 09/09/2011 E2 N Remove glass. DO NOT ALLOW THE FIXTURE TO HANG FROM THE WIRING HARNESS. E3 E4 H J L Connect wiring harness. Attaching the Grille E1 H M Remove the thumbscrews. D24 Go to step E1 on page 18 to attach grille. If the...

Owner's Manual - Page 19

... of electrical shock, all plug connections to make sure it matches the wiring diagram. Solution: • H unter Fan Bath Ventilators are secure. • C heck the wiring to be properly installed. To confirm that the fan is running, place your hand near the vents to feel the air movement. • T urn power on...

Owner's Manual - Page 20

...IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. Proof of the Hunter Fan Company Service Department, 2500 Frisco Avenue, Memphis, Tennessee 38114. THE DURATION OF ANY ...OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN RESPECT TO ANY HUNTER FAN BATH EXHAUST FAN MOTOR OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE PERIOD OF THE EXPRESS WARRANTY SET...