Hunter 90064 Support Question

Find answers below for this question about Hunter 90064.
Need a Hunter 90064 manual? We have 1 online manual for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by gillenterry on October 12th, 2019

How Does The Night Light Work

installed unit but the night light isn;t working

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on October 12th, 2019 9:42 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,700

1,090
points

See Problem: Light does not come on at https://www.manualslib.com/manual/508389/Hunter-Ellipse-90064.html?page=19#manual. (If needed, a wiring diagram is at https://www.manualslib.com/manual/508389/Hunter-Ellipse-90064.html?page=6#manual. You may need professional help.)

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Hunter 90064 Manual Pages

Owner's Manual - Page 1

Owner's Manual - Page 2

...unit, switch power off power unit. 3. Installation work and electrical wiring must be done by qualified person(s) in the housing (next to the outdoors. 7. When cutting or drilling into the slot in accordance with the exact service motor. This unit...OUT SERVICE PANEL BEFORE SERVICING UNIT PREVENTATIVE MAINTENANCE A clean fan provides better service. Gently vacuum fan, motor and interior of...

Owner's Manual - Page 3

...-01-000 F 75190-01-000 G 03242-07-133 H 95492-02-000 x2 I Extra Screws * NOTE: Strain relief cable connector must be installed. If damaged, call 1-888-830-1326 for replacements. Before Installation 1 30 20 O FF O FF Tools Needed. (Not supplied) Estimated assembly time: 30 to 60 minutes NOTE: Remove all the parts...

Owner's Manual - Page 5

Choose Installation Option For New Construction - accessible only from above go to joist A11 E A12 5/8 1/2 5/8 1/2 Position the correct depth mark at the bottom edge of the joist ...

Owner's Manual - Page 6

... wiring cover plate. 6 41722-01 09/09/2011 Tighten the wiring cover plate screw. A15 F A16 2 1 F G• Install the wiring cover plate. A14 Fan Motor Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch...

Owner's Manual - Page 9

Screws are not provided. B19 Fan Motor Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC In) Connect wires as shown. 9 41722-01 ...

Owner's Manual - Page 10

... up into position. B23 H Connect 4" duct and vent to be purchased. B24 Connect wiring from the motor to the wiring cover plate. Tape joints. B20 F 2 1 F Install the wiring cover plate. B22 B21 G• Tighten the wiring cover plate screw.

Owner's Manual - Page 11

... source. B27 ON OFF Test the motor. If the motor does not run, check the plug connection. accessible from above C11 EXISTING FAN NO EXISTING FAN OR Remove an existing fan and check to make sure the opening is large enough to mark position. 11 41722-01 09/09/2011 Existing Construction - Use...

Owner's Manual - Page 14

... sure all wiring connections are not pinched 14 between the motor and the housing. 41722-01 09/09/2011 C22 Fan Motor Night Light Light Black 2 Pin White 3 Pin White Red Night Light Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC In...

Owner's Manual - Page 15

accessible only from below D11 EXISTING FAN D12 E Remove an existing fan and check to make sure the opening is large enough to step E1 OFF on the power source. If the motor does not run, check ...

Owner's Manual - Page 16

... into joist or framing. Tape joints. If ducting does not fit securely, an adapter may need to duct connector. D16 Fan Motor Night Light Light Black 2 Pin White White Red Night Light 3 Pin Black Light *Option *Option Fan & Main Light Together Ground Green A Bare Copper Black Main Switch 1 (AC In) White Red Switch 1 (AC In) Black Switch 2 (AC In...

Owner's Manual - Page 17

... H Connect wiring from the motor to the wiring cover plate. Make sure the wires are inside the box or under the wiring cover plate. D17 2 1 F Install the wiring cover plate.

Owner's Manual - Page 19

...C heck the wiring to make sure it moves freely. Solution: • H unter Fan Bath Ventilators are secure. • C heck the wiring to make sure it is ...Install 2 Max 60 Watt A-15 bulbs (Not Included) and 1 Max 7 Watt C-7 bulb (Not Included). N Align glass and push up. Solution: • R eplace the light bulb with a new bulb. • T urn power on . Problem: Light...

Owner's Manual - Page 20

... PARTICULAR PURPOSE, IS MADE IN RESPECT OF GLASS FIXTURES OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN. THE DURATION OF ANY IMPLIED WARRANTY, INCLUDING, BUT NOT ... provided free of charge at any Hunter bath exhaust fan which were caused by repairs by persons not authorized by us, mishandling, improper installation, modifications or damage to us . IF THE ORIGINAL...