Hunter 44550 Support Question
Hunter 44550 Support Question
Find answers below for this question about Hunter 44550.Need a Hunter 44550 manual? We have 2 online manuals for this item!
Question posted by oschool4612 on October 10th, 2012
What Does Recv Means On Therastat
The person who posted this question about this Hunter product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by quaff on October 11th, 2012 8:27 AM
quaff
Member since:
November 13th, 2011 Points: 537,590
Member since:
November 13th, 2011 Points: 537,590
The RECV indicates that the unit is running in Auto Recovery mode. What this means is that it is "transitioning" from an energy-saving setpoint to a comfort setpoint. For example, if you program the system to be at 65 starting at 11 p.m. and to be at 72 starting at 7 a.m., and the temperature drops to 65 overnight, the system will enter Auto Recovery (RECV) prior to 7 to get the temperature to 72 by 7 a.m.
I hope that this helps!
Related Hunter 44550 Manual Pages
Owner's Manual - Page 1
SINCE
®
1 8 8 6
AUTO SAVER 550
5:22
3 72
OwnerÕs Manual
Model 44550
Owner's Manual - Page 3
... assistance, call Hunter Technical Support at 901-745-9222 from 8 a.m. If you for complete instructions on installing and operating your thermostat will provide years of use. Your new Hunter electronic thermostat will pay for itself during its first season of reliable service. Central Time.
Model Information: Model Number ____4_4_5_5_0 Serial Number Date...
Owner's Manual - Page 4
Table of Contents
INTRODUCTION INSTALLATION
PROGRAMMING
OPERATIONS
Read This Before Installing Thermostat Features
What You Need Remove Old Thermostat Wire Labeling Mount Wallplate and Thermostat Selector Switches
Setting Time and Day Auto Programming Personal Program Schedule Manual Programming Weekday / Weekend Programming 7-Day Programming Reviewing Programs Reviewing the Current Temperature ...
Owner's Manual - Page 6
... temperatures from 32°F to the heating system control.
Note: At initial power-up this thermostat is below 32°F (0°C). It does not provide a delay when there are power ... Note that do not have 24-volt or millivolt control systems and
COMPRESSOR PROTECTION
5 The thermostat provides a 3.5 minute delay after shutting off the heating or cooling system before it will prevent...
Owner's Manual - Page 7
..., install 2 new AA batteries.
BATTERY WARNING
9 Fresh alkaline batteries should provide over 30 days, we recommend that you plan to change the batteries and keep thermostat's clock and program settings. Once the batteries have approximately 1 minute to be cleared except for "BATT" flashing on the display with new alkaline batteries prior...
Owner's Manual - Page 8
... Week, Last Week, or Total.
Battery Door: Frontaccess battery door allows easy battery changes. HOME TODAY: Overrides energysaving program temperatures while you can program the thermostat to allow display viewing in the dark. System Switch: System selector switch for Automatic or Continuous On fan operation. Fan Switch: Fan switch for Cool...
Owner's Manual - Page 9
...PROG
PROG DAY
MIN
DAY
AUTO PROGRAM
HOLD CLEAR
FILTER RETURN
Automatically programs the thermostat to current time and temperature. See page 17. Returns display to its ... settings.
As an ENERGY STAR® Partner, Hunter Fan Company has determined that this programmable thermostat meets the ENERGY STAR® guidelines for reviewing and changing weekday, weekend, or daily programs....
Owner's Manual - Page 10
... for screws, tabs, etc. s Slotted Screwdriver(s) s Phillips Screwdriver s Hammer s Electric drill and 3/16" bit s Two 1.5 V (AA) size alkaline batteries
Remove Old Thermostat
CAUTION: Do not remove any wiring from existing thermostat before reading the instructions carefully. Once wall mounting plate is exposed, look for mounting. Turn off the power to the back...
Owner's Manual - Page 11
...procedures correctly, you may want to tape them from the existing thermostat terminals. s If hole in Table A on this thermostat.
BEFORE DISCONNECTING ANY WIRES, APPLY THE SELF-ADHESIVE LABELS PROVIDED TO...then connect the other wire to the W terminal to non-battery powered thermostats.
This air could cause a false thermostat reading.
Table A
NOTE: Do not connect a "Common" wire (...
Owner's Manual - Page 12
... until flush with those on the Hunter wallplate. Mark holes for appearance. INSTALLATION
12-13
Mount Wallplate and Thermostat
s Remove the wallplate from your thermostat by pressing the release tab on the bottom of the thermostat. (See Figure 2.)
s Position wallplate on wall and pull existing wires through large opening .
Then level for plastic...
Owner's Manual - Page 13
... AA size alkaline batteries, observing the polarity marked on the unit.
Connect Wires and Mount Thermostat Cover to Wall Plate
s Match and connect the labeled wires to the appropriate coded terminal ...(See Figure 4, 5.) Ignore any wires which were not connected to the old thermostat. Press top of the thermostat cover.
If it into hole to prevent interference with your system has an ...
Owner's Manual - Page 14
... switch to see whether the Heat and Fan come on the printed circuit board inside the thermostat. NOTE: "HG" position is for gas and most other selector switches that allow you ... s Heating system selector (HG - If you have an electric furnace, test to OFF before removing the thermostat from the wall. If Fan operation is in the "HG" position. O - There are also other systems. "HE...
Owner's Manual - Page 15
... Switches:
s F° / C° selector (Fahrenheit / Centigrade) - Switch 5 Your thermostat is pressed, the thermostat will automatically change temperature mode. NOTE: Unless the reset button is set from the factory.
... the reset button on the circuit board for a complete discussion of the thermostat with the EPA ENERGY STAR® Program. s Auto Recovery selector -
...
Owner's Manual - Page 16
... to advance
MIN
one minute at right. PROGRAMMING
16-17
Setting Time and Day
Remove the mylar label covering the LCD display window before operating thermostat.
1 2 : 0 0 M T W Th F Sa Su SET TEMP
s Initial display after a few seconds.
72
AUTO COOL HEAT TEMP
°HC
EXAMPLE: Set the...
Owner's Manual - Page 17
... weekend day can reduce your fuel bill by the Department of 4 programs.
Your Hunter thermostat is pre-programmed to meet the ENERGY STAR® guidelines for all weekdays, Monday
to... Sunday, can be programmed for energy efficiency. A U : T O AUTO s Press once. Your thermostat is easier to modify these programs than to Manual Programming on page 19 for two 8-hour periods during winter...
Owner's Manual - Page 19
... unique programs for all 4 programs set your comfort program times early.
Manual Programming
s Your thermostat can be used when entering programs for 68°F (20°C) in Heat mode and 78...Programming.
NOTE: There are used for programming.
5) After 15 seconds without a key press, the thermostat will return to normal display mode.
6) When setting the program time, note the AM / PM ...
Owner's Manual - Page 20
... shown. PROGRAMMING
20-21
Weekday/Weekend Programming (cont.)
Step 2
s Press PROG key to the other system, and repeat Steps 2 through 6 above. s After 15 seconds, the thermostat will return to change the setpoint temperature.
Step 3
Use HOUR and
MIN to normal mode automatically.
Use
and
to change the setpoint time.
Owner's Manual - Page 21
... COOL HEAT TEMP
°HC s Press to move to complete the programs for Monday. PROG
s Repeat Step 3 to programs 2, 3 and 4.
RETURN
s After 15 seconds, the thermostat will return to program the corresponding system.
7-Day Programming
Step 1
COOL OFF HEAT AUTO s Slide System Selector Switch to HEAT or COOL to normal mode...
Owner's Manual - Page 23
... M T W Th F Sa Su SET TEMP
AM
°C
PM
H
Refer to normal mode. s Press repeatedly to normal mode. s Thermostat is set to AUTO, and the heating system is on.
8 9 : 1 5 M T W Th F Sa Su SET TEMP
AM
...mode is different. s If held for 1 second or less. s After 15 seconds, the thermostat will be blank when at least one of the
weekend programs is shown above current room temperature....
Owner's Manual - Page 30
...switch on approximately 30 minutes early. Otherwise, the recovery process will be changed then the thermostat will recalculate Auto Recovery again. For example, in operation. Setpoint temperature will be about... recovery process. Auto Recovery works in Auto Recovery mode, the display will alternate "RECV" with time, and the program indicator will be canceled and change to Home Today...
Similar Questions
