Hunter 44260 Support Question
Hunter 44260 Support Question
Find answers below for this question about Hunter 44260.Need a Hunter 44260 manual? We have 2 online manuals for this item!
Question posted by Anonymous-173071 on November 17th, 2022
Help Hunter Model 44260
For the pass six months having problems with the up & down buttons. Can the up n down buttons be fixed? U push them nothing happen, it's a great thermostat except for these rubber up and down arrows. Please help. Cind
Current Answers
Answer #1: Posted by SonuKumar on November 17th, 2022 8:28 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,621,300
Member since:
May 9th, 2021 Points: 16,621,300
Related Hunter 44260 Manual Pages
Owner's Manual - Page 1
Set & $ave
Programmable Thermostat
installation and operation manual
English
Form# 42711-01
20091118
©2009 Hunter Fan Co.
1
Model
44260
Owner's Manual - Page 3
Table of Contents
Important Information 5
Tools
6
Uninstalling the Existing Unit 7
Installing the Thermostat 12
installing the wall plate 12 connecting the wires 16 attaching the thermostat 18
Settings 22
Methods of Operation 26
manual operation 28 default programs 32 creating custom programs 34
Icons and Features 38
Wiring 49
Troubleshooting 52
3
Owner's Manual - Page 4
Your new Hunter thermostat will provide years of reliable service and year-round energy savings.
Set & Save
Programmable Thermostat
Model 44260
Congratulations!
Thank you for complete operation instructions.
4 Please read this manual before beginning installation and save this booklet for choosing a Hunter programmable thermostat.
Owner's Manual - Page 5
... systems:
Gas - Fired Boilers Gas - Milivolt Systems
Oil - Standing Pilot Gas - Fired Furnace
Electric Furnace Electric Air Conditioning Single Stage Heat Pump - important information
This thermostat is not designed for multi-stage heat pump systems or 110/220 V baseboard heating systems.
If you are unsure what kind of heating and cooling...
Owner's Manual - Page 6
Tools This thermostat includes two #8 slotted screws
and two wall anchors for mounting. To install your new thermostat, you will need the following supplies:
Flat-head screwdriver
Small Phillips-head screwdriver
Hammer
Electric drill and 3/16" bit
Two 1.5 Volt (AA) size alkaline batteries
6
Owner's Manual - Page 7
The wires must be labeled prior to removal to ensure proper reconnection.
7 Do not disconnect the wires from the existing thermostat before reading these instructions. NOTICE!
Owner's Manual - Page 9
... to expose the wires and mounting screws.)
9 Some models may have multiple covers, screws or other locking devices that open to the HVAC system OFF at the main power panel or at the furnace.
2. Turn the system power OFF from the wall.
(Some thermostats may be removed or disengaged.)
3. Locate, but do...
Owner's Manual - Page 10
RH / R / VR / 4
RC / VC
Y / C* / M / O
label the wire with this sticker:
24 Volt RH
24 Volt cool RC
air conditioning compressor
W / H / B G / F Y1
heating
fan heat pump compressor
Y/0 W/B
G
Y1
10 Y1 G W/B Y/0 RC RH
if your existing thermostat is marked...
Owner's Manual - Page 11
... not let the wires slip back into the wall during disconnection. uninstalling the existing unit, cont.
4. Refer to the existing terminal designation for nonbattery powered thermostats.
5.
Owner's Manual - Page 13
... the Hunter wall plate, or if there are no existing holes, visually level the wall plate and mark the wall for two holes.
13 If the existing holes do not match those on the wall and pull the labeled wires through the opening.
3. Remove the wall plate from the new thermostat by...
Owner's Manual - Page 15
... wires through the wall plate and into the holes until
they are flush with the wall. 6. Tap the plastic anchors into the anchors. installing the thermostat, cont. 4. Remove the wall plate and drill two 3/16"
holes where marked. 5.
Owner's Manual - Page 17
...Match and connect the wires from the wall to prevent interference. 17 CONNECTING THE WIRES
1. Push any extra wires should be wrapped in
2.
Note: A jumper wire has been provided, connecting... not provide both an RH and RC wire, leave the jumper in
electrical tape and carefully pushed back into the wall to the terminals as shown. Tighten each screw after the connection has ...
Owner's Manual - Page 19
.... Locate the System Type switch on the back of the thermostat. Locate the Auto Recovery switch on the back of the thermostat. If you wish to use this feature, simply change the...switch has no effect when the system is in the ENABLE position. installing the thermostat, cont. ATTACHING THE THERMOSTAT
Lift the thermostat cover and set to HG (default) for gas furnace and oil burners. ...
Owner's Manual - Page 21
... the wall plate, as the terminal pins may not work.
5. Press the thermostat onto the wall plate and press to snap the bottom tab into place properly, the unit may be damaged. Place the top of the thermostat over the two
tabs on the wall plate.
Insert two AA alkaline batteries. 6. Restore...
Owner's Manual - Page 23
... (Co):
1. Continue to Fo, press only the Reset button.
23
Press and hold the Up button. 2. To reset the unit to press the Up button, but release
the Reset button when the LCD turns on. Use a paperclip to press the Reset button. 3. NOTICE: CHANGING THIS SETTING WILL RESET THE THERMOSTAT TO FACTORY DEFAULT PROGRAMS.
(If no...
Owner's Manual - Page 25
...The AM/PM indicator will
flash) 2.
Press Day/Time. (AM/PM and current hour will be off when the thermostat is in 24 hour mode.
Press Day/Time to return to adjust the day of the
week. 5. Setting day and... 24 hour format by pressing Day/Time and then Program. The default for this thermostat setting is in a 12 hour format. You can change the format to adjust the minute
setting. 4.
Owner's Manual - Page 27
To utilize the pre-programmed settings, see pages 34-37.
27 To create custom programs, see pages 32-33. For manual operation instructions, see pages 28-31. methods of operation This thermostat gives you the ability to program up to 4 custom temperature settings per day or utilize pre-programmed settings.
Owner's Manual - Page 29
If you want to enter Manual Override mode. (Release the button
when the display flashes.)
2. Press and hold Up or Down for the current ... settings for one second to only override the current program: 1.
Press the Up or Down buttons to operate their thermostats manually, adjusting settings as desired.
29 MANUAL OPERATION
Many people prefer to adjust the temperature setting as needed.
Owner's Manual - Page 31
... Up or Down for one second to the normal display.
31 Press and release Hold/Return to return to enter Manual Override mode. (Release the button
when the display flashes.)
3. If you want to adjust the temperature setting as desired. 4. methods of operation, CONT. MANUAL OPERATION, CONT. Press the Up or...
Owner's Manual - Page 55
Visit http://www.hunterfan.com for more information. Can't I just call someone?
Sure.
They may be reached toll-free at 1-888-8301326.
55 Our Technical Support Group is available from 8 am to 5 pm CST. Is there help on the web? Yes.
Similar Questions
What Do A Blinking 4 Mean On A Hunter Thermostat 44260
44260 Hunter thermostat blinking 4 what does it mean
44260 Hunter thermostat blinking 4 what does it mean
(Posted by Rickandremodel 3 years ago)
Hunter Fan 44260 Programmable Thermostat Manual What Do The Programs Do
(Posted by stera 10 years ago)
