Hunter 44110 Support Question
Hunter 44110 Support Question
Find answers below for this question about Hunter 44110.Need a Hunter 44110 manual? We have 3 online manuals for this item!
Question posted by scnewtons on August 23rd, 2014
Hunter 44110 Continues To Run
Hunter 44110 at times continues to run past programed temp. it is not in the hold mode and I have replaced batteries. after pressing hold/return button system resets its self. problem is someone not always at home to reset and system runs and runs. starting to cost $$.
Current Answers
Answer #1: Posted by TechSupport101 on August 25th, 2014 7:55 AM
TechSupport101
Member since:
May 24th, 2013 Points: 12,171,305
Member since:
May 24th, 2013 Points: 12,171,305
Hi. The Troubleshooting tutorial here http://www.ehow.com/way_5661656_hunter-thermostat-troubleshooting.html should be able to assist much.
Related Hunter 44110 Manual Pages
Owner's Manual - Page 3
Set & $ave
Programmable ermostat installation and
operation manual
Model 44110
42707-01 3-7-06
Owner's Manual - Page 5
Table of Contents
Important Information 5 Tools 6 Uninstalling the Existing Unit 7 Installing the Thermostat 12
installing the wall plate 12 connecting the wires 16 attaching the thermostat 18
Settings 22 Methods of Operation 26
manual operation 28 default programs 32 creating custom programs 34
Icons and Features 38 Troubleshooting 49
3
Owner's Manual - Page 6
Set & Save
Programmable Thermostat
Model 44110
Congratulations!
Your new Hunter thermostat will provide years of reliable service and year-round energy savings. Thank you for complete operation instructions.
4 Please read this manual before beginning installation and save this booklet for choosing a Hunter programmable thermostat.
Owner's Manual - Page 7
IMPORTANT INFORMATION
This thermostat is not designed for heat pump systems or 110/220 V baseboard heating systems.
If you are....
5 Fired Boilers Oil - Milivolt Systems
Oil - Standing Pilot Gas - Fired Furnace
Electric Furnace Electric Air Conditioning
This thermostat is designed to work on the following heating and cooling systems:
Gas - Electronic Ignition
Gas - Fired Boilers Gas -
Owner's Manual - Page 8
To install your new thermostat, you will need the following supplies:
Flat-head screwdriver
Small Phillips-head screwdriver
Hammer
Electric drill and 3/16" bit
Two 1.5 Volt (AA) size alkaline batteries
6 TOOLS This thermostat includes two #8 slotted screws and two
wall anchors for mounting.
Owner's Manual - Page 9
Do not disconnect the wires from the existing thermostat before reading these instructions. The wires must be labeled prior to removal to
ensure proper reconnection.
7 NOTICE!
Owner's Manual - Page 11
....)
3. Some models may have doors that must be connected to the back of the wall plate. Turn the system power OFF from the wall.
(Some thermostats may have multiple covers, screws or other locking devices that open to the HVAC system OFF at the main power panel or at the furnace...
Owner's Manual - Page 13
... color should not be ignored. Refer to the chart.
(If the terminals are labeled, disconnect each wire according to the existing terminal designation for non-battery powered thermostats.
5. This wire is used . Using the provided stickers, label each wire and remove the existing wall plate.
11 If you disconnect them. Do not...
Owner's Manual - Page 15
Position the new wall plate on the bottom of the thermostat.
2. Remove the wall plate from the new thermostat by pressing the release tab on the wall and pull the labeled wires through the opening.
3. If the existing holes do not match those on the Hunter wall plate, or if there are no existing holes...
Owner's Manual - Page 17
INSTALLING THE THERMOSTAT, CONT. 4. Insert the mounting screws through the opening. Tap the plastic anchors into the anchors. Reposition the wall plate on the wall, pulling the
wires ...
Owner's Manual - Page 19
INSTALLING THE THERMOSTAT, CONT. Loosen, but do not provide both an RH and RC wire, remove this jumper. Match and connect the wires from the wall to prevent ...
Owner's Manual - Page 20
Thermostat
T
Cover
AM 4
HEAT
System Switch
DISABLE
RECOVERY
ENABLE
HG HE
W/B Y/O RH RC G
18
Owner's Manual - Page 25
Continue to F, press only the R button.
23 To reset the unit to press the U button, but release the
Reset button when the LCD turns on. Use a paperclip to Celcius (Co): 1. Press and hold the U button. 2. SETTINGS The default setting of the thermostat is Fahrenheit (Fo).
(NOTICE: CHANGING THIS SETTING WILL RESET THE THERMOSTAT TO FACTORY DEFAULT PROGRAMS.)
To change to ...
Owner's Manual - Page 27
... display.
25 You may also press Hold/Return at any time to return to adjust the setting. 3.
Setting day and time: 1.
You can change the format to adjust the day of the week. 5.
Press D/T again to 24 hour format by pressing D/T and then Program. Press D/T...
Owner's Manual - Page 37
... set in increments of 1o
F (1o C). • After 15 seconds of inactivity during programming,
the thermostat will return to Normal Display mode. • When setting the program time, note the AM/PM
indicator. • Press Hold/Return at any time to exit Program mode. • If no button is pressed for 5 seconds, the unit will
begin to flash)
35 Slide the to HEAT or...
Owner's Manual - Page 43
... your system is RESET, the span cycle will decrease your cycle time by allowing the system to run longer; Down will revert to adjust the system ON/OFF cycle rate. When batteries are installed, or the unit is cycling too fast or too slowly. Press and hold both the U and D buttons until the...
Owner's Manual - Page 50
Compressor Protection After the system stops running in cooling mode, there will be a 3.5 minute delay before it can be restarted to prevent compressor damage due to the original factory settings, press the reset button
with a paperclip.
(This will erase any user-programmed settings.)
48 Resetting the unit
reset
To restore the thermostat to rapid cycling.
3. Temperature Range
30o F (...
Owner's Manual - Page 53
Replace unit.
8. How do I just operate my thermostat manually?
9 a. Replace unit.
9. Manual operation instructions are on pages 28-31.
51 My system continues to operate when the thermostat
is in the off position.
7 a. TROUBLESHOOTING 7. The LCD screen permanently reads HI, LO, or ERR.
8 a.
Owner's Manual - Page 1
...
terminal on the
bottom of the thermostat body to snap it will not function when the thermostat is wired correctly. ■ Be sure to your existing thermostat is no hot or cold air can be damaged. TH PM
3 HEAT TEMP
HEAT OFF COOL FAN ON AUTO
DAY/TIME PROGRAM
RESET
HOLD/RET
Battery Compartment: Front access allows easy insertion...
Owner's Manual - Page 2
... switches on front of the thermostat with a small pin and hold your system Off.
Note: The thermostat will remain shut-off in the "HG" position. Error Mode If the thermostat is pressed, the thermostat will enter Error Mode. Next, use a paper clip to press the RESET button next to enter time and day setting
M
mode. Replace Batteries
1. Friday
Saturday - NOTE: "HG...
Similar Questions
How Do I Run My Air Conditioner Automatically Without Scheduling It
How do I run my ac automatically with out scheduling it
How do I run my ac automatically with out scheduling it
(Posted by zaracox40 2 years ago)
Hunter 44110 Span 3 Flashing
My boiler heats up but my radiators are cold and my thermostat is flashing 3
My boiler heats up but my radiators are cold and my thermostat is flashing 3
(Posted by mazziequad 4 years ago)
Reprogram A Hunter 44110 Programmable Thermostat
I am having trouble permenatly over riding the thermostate. Any suggestions?
I am having trouble permenatly over riding the thermostate. Any suggestions?
(Posted by rktk 8 years ago)
In Our Warehouse The Hunter 44110 Screen Was Blank So We Changed Batteries But I
It now shows "0" and we cannot change it ? Help
It now shows "0" and we cannot change it ? Help
(Posted by Johnsarrail 9 years ago)