Hunter 28681 Support Question
Hunter 28681 Support Question
Find answers below for this question about Hunter 28681.Need a Hunter 28681 manual? We have 4 online manuals for this item!
Question posted by Omprakash1 on January 24th, 2021
I Need Rubber Grommets For A Model 28681 To Secure Blades.
I had to search for a white grommet and hope that they were the right part for the ... for a Hunter ceiling fan # 208145 It is a white fan but can use black ones as well
Current Answers
Answer #1: Posted by hzplj9 on January 25th, 2021 3:06 PM
hzplj9
Member since:
June 25th, 2012 Points: 4,875,670
Member since:
June 25th, 2012 Points: 4,875,670
If they are standard rubber grommets then a site like Ali-express or Ebay would be able to supply a suitable alternative. You only need to know the size of the hole to obtain the size of the grommet. And then you need the size of the screw to allow the fixing to go through the grommet. This will then give the necessary support.
Just put grommet in your search.
Example: https://rb.gy/j5dald for Ali.
https://rb.gy/hdnhl1 for Ebay
Hope that helps.
Answer #2: Posted by Odin on January 25th, 2021 10:37 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,640
Member since:
April 10th, 2010 Points: 41,236,640
If you can't get what you seek from the manufacturer [use the contact information at https://www.contacthelp.com/hunter/customer-service], request a part number. Then (with or without a part number) try
- https://encompass.com/
- https://www.diyspareparts.com/
- a search engine like Google's or Bing
- http://www.searchtempest.com/, which displays global listings from eBay, Craigslist, and other sources
(For option 4, you may want to use a free tracking program like https://www.followthatpage.com/ to save you from having to repeat your search over time.)
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Hunter 28681 Manual Pages
Installation Guide - Page 1
..., determine if it is suitable, go to your fan manual and begin with the rotating fan blades during normal operation.
• e fan blades are at least 8 feet high.
• e fan blades have now successfully prepared your new Hunter fan. Position it will support the full weight of 1/16" into ceiling. Obtain a UL-approved octagonal 4" x 1-1/2" outlet box, plus two...
Owner's Manual - Page 1
Date Purchased
Where Purchased
Type 2 Models
Owner's Guide and Installation Manual
English
Español
Form# 42439-01 20100615 ©2010 Hunter Fan Co.
For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name
Model No.
Owner's Manual - Page 2
...
support structure of fire, electrical shock, or motor damage, do not bend the blade attachment system when installing, balancing, or cleaning the fan. Welcome
Your new Hunter® ceiling fan is an addition to your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as a tag, to the service panel. • All...
Owner's Manual - Page 3
...; e fan blades are at least 7 feet above the floor and the ceiling is at least 8 feet high.
• e fan blades have no obstructions to airflow, such as described on this page. Wiring
• e electrical cable is recessed a minimum of the outlet box is secured to Section 2 • Installing the Ceiling Plate. If your new Hunter fan.
Owner's Manual - Page 4
... into the ceiling. Install a Support Brace, If Necessary
Determine if there is positioned to allow you to ensure it will use a qualified electrician.
4
42439-01 • 06/15/10 • Hunter Fan Company Attach... into the ceiling. If you cannot lock the circuit breakers in accordance with the joist or support brace.
4-3.
If you are turned off position, securely fasten a ...
Owner's Manual - Page 5
... and wobble-free performance. All Hunter fans use only the hardware supplied.
5 42439-01 • 06/15/10 • Hunter Fan Company You can purchase Hunter extension downrods. The steps in one of the building according to these instructions, and use sturdy 3/4" diameter pipe to the support structure of three ways, depending on ceiling height and your preference: Low...
Owner's Manual - Page 6
... the motor or fan blades. Proper ceiling fan location and attachment to the building structure are installing more than one fan, keep the fan blades and blade irons (if applicable) in sets, as they were shipped.
6 42439-01 • 06/15/10 • Hunter Fan Company Gathering the Tools
You will need help installing the fan, your Hunter dealer or call Hunter Technical Support Department...
Owner's Manual - Page 7
...use lubricants on each other. Ceiling Plate
3" Wood Screw
Steps 2-3 - 2-6
7 42439-01 • 06/15/10 • Hunter Fan Company Note: The isolators should be flush against the ceiling... the ceiling plate. 2-5. 2 • Installing the Ceiling Plate
CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning off position, securely fasten ...
Owner's Manual - Page 8
... that the canopy slots sit on one side of the pin in the ball. 3-3. Securely retighten the setscrew with the holes in... in the adapter. Assemble securely with the lip down. 3-6. Insert the downrod through the downrod on the ceiling plate hooks. 3-7. Do .../10 • Hunter Fan Company Place the low profile washer into the canopy with three low profile screws. Raise the fan and align the...
Owner's Manual - Page 9
... the ceiling to the black (ungrounded) and the black/white wire (ungrounded) from the fan. 4-5. Turn the splices upward and push them , then twist clockwise until tight. If you are not included. For all these connections use the wire connectors provided. 4-3. 4 • Wiring the Fan
All wiring must be in accordance with the grounded wires on one side...
Owner's Manual - Page 10
...8226; 06/15/10 • Hunter Fan Company
Verify that must remain engaged while swinging the canopy for the following steps could cause the fan to the top of the trim ring...securely tighten all the holes are still in the canopy. Using both hands, push the canopy trim ring up to fall. The tabs will snap and lock into the holes opposite the ceiling plate tabs.
5-4.
Swing the fan...
Owner's Manual - Page 11
... likely to prevent
scratching the blades. 2. Once they are loosened, finish unscrewing them
counterclockwise. Cover the blade iron posts with the blade iron. 6-.2 Push the blade down onto the three blade iron posts; Carefully remove the blade.
11 42439-01 • 06/15/10 • Hunter Fan Company
Step 6-1 Step 6-2 Do not use a furniture polish or any other cleaners...
Owner's Manual - Page 12
... US federal energy regulations, this fan model. 7-1. Connect the upper plug connector from the motor to be operating properly, see the troubleshooting section. 7 • Completing Your Installation With a Bowl Light Fixture
Upper Switch Housing
Plug Connector
Housing Assembly Screw
WARNING: Use only the light fixture supplied with this ceiling fan contains a device that restricts its...
Owner's Manual - Page 13
...
Cover Plate Finial
13 42439-01 • 06/15/10 • Hunter Fan Company 7 • Completing Your Installation With a Bowl Light Fixture (Continued... pull chain through the grommet hole in the cover plate and glass bowl. 7-10. Thread the fan pull chain through the...the extra pull chains (included) to the light and fan pull chains using the plastic breakaway connector. (You may find the ...
Owner's Manual - Page 14
... recoiling into the connector.
8-3. Ceiling fans work best by blowing air downward (counterclockwise blade rotation) in sequence: High, Medium, Low and Off. • Pull the chain slowly to change settings. • Release slowly to the light fixture. Use a dry or slightly damp lint free cloth to cool the room with Hunter's Dust Armor protection, making...
Owner's Manual - Page 15
... you need parts or service assistance, please call 1-866-268-1936) or visit us at our Web site at the wall switch. Loosen canopy, check all blade iron screws. 3. Push motor reversing switch firmly left or right to the light socket. 2. Check to ensure it is still operating 1. If so, replace all the blades.
Hunter Fan...
Parts Guide - Page 1
... Assembly
Blade Assembly
Switch Housing Assembly
Fan Parts
(Not Drawn to Scale)
150
PARTS GUIDE
Using this Parts...Model #
28679
Asm. REFER TO THE INSTALLATION MANUAL FOR FULL ASSEMBLY INSTRUCTIONS. Dwg. # G0829-01
28680 G0829-02
28681 G0829-03
Finish
Qnty 1
Onyx Bengal Brushed Nickel
White...77646-04
1
65666-01
65666-01
65666-01
Hunter Fan Company • 7130 Goodlett Farms Pkwy. #400...
Similar Questions
I Need Rubber Grommets For A Model 28681 To Secure Blades.
I need the rubber grommets for model 28681 to secure the blades.
I need the rubber grommets for model 28681 to secure the blades.
(Posted by mgregan05 3 years ago)
Hunter Fan Pull Chain Switch Inoperable.
Good morning, I have a Hunter low profile 48" ceiling fan, model # 28681. The pull chain switch is s...
Good morning, I have a Hunter low profile 48" ceiling fan, model # 28681. The pull chain switch is s...
(Posted by Bakkatcha 5 years ago)
The Rubber Grommets Are Installed In The Holes In The Fan That Are Then Secured
to the fan blade arm with screws that go thru the grommet.
to the fan blade arm with screws that go thru the grommet.
(Posted by bobwinton 10 years ago)
Where Can I Purchase Rubber Grommets For My Hunter Fan?
(Posted by bobwinton 10 years ago)