Home » Hunter » Fans » Hunter 20182

Hunter 20182 Support Question

Find answers below for this question about Hunter 20182.
Need a Hunter 20182 manual? We have 4 online manuals for this item!

Hunter Overview Questions Manuals Reviews Videos Research

Question posted by bjmccoy on May 27th, 2012

Lights

when i turn the lights on, there is a delay of coming on. i have checked the wires and replaced the light kit. the model # is 20182

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hunter 20182 Manual Pages

Installation Guide - Page 1

...from outlet box. Step 5 Step 5 Prepare the Wiring 5-1. If you cannot check off . Choose a fan site where: • No object can come in accordance with national and local electrical codes and ... of the fan and light kit. Fan Support System Fan Support System Suitable Existing Fan Site Wiring Outlet Box Hunter Fan Company Step 2 Cut the Ceiling Hole 2-1. Preparing the Fan Site 8' ...

Owner's Manual - Page 1

For Your Records and Warranty Assistance For reference, also attach your receipt or a copy of your receipt to the manual. Model Name Model No. Date Purchased Where Purchased Type 2 Models Owner's Guide and Installation Manual English Español Form# 42626-01 20110505 ©2011 Hunter Fan Co.

Owner's Manual - Page 2

... BEFORE BEGINNING INSTALLATION. SAVE THESE INSTRUCTIONS. • Use only Hunter replacement parts. • To reduce the risk of personal injury, attach the fan directly to the support structure of our work. Before installing your fan, for installing and operating your fan, disconnect the power by turning off position, securely fasten a prominent warning device, such as...

Owner's Manual - Page 3

... joist or support brace by an approved connector. • Six inches of the fan and light kit. Fan Support System • Fan attaches directly to airflow, such as described on this page. Preparing the Fan Site Step 1 - Choose a fan site where: • No object can come in contact with joist or support brace. • e bottom of the...

Owner's Manual - Page 4

...16" into the ceiling. Check the support brace to ensure it to allow you to your ceiling fan site. Attach the outlet box... or support brace. 4-3. Make certain the wiring meets all national and local standards and ANSI...fan. 2-2. Attach the fan supply line to the service panel. 5-2. read the fan supply line through the inner holes of the fan and light kit. If you are turned...

Owner's Manual - Page 5

... fits close to these instructions, and use only Hunter speed controls. All Hunter fans use the accessories, follow the instructions included with each product. The steps in one...higher than 8 feet high CAUTION: To reduce the risk of personal injury, attach the fan directly to assure stability and wobble-free performance. Installer's Choice and Optional Accessories Support Brace...

Owner's Manual - Page 6

... and blade irons (if applicable) in ceiling. • Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. Installing Multiple Fans? Check for installing the fan: • Electric drill with 9/64" bit • Standard screwdriver (magnetic tip recommended) • Phillips-head screwdriver (magnetic tip recommended) • Wrench...

Owner's Manual - Page 7

...the center of the two 3" wood screws. 2-4. Check to orient the ceiling plate so that the two ... flat washer on the screws. Thread the supply wires from each of the ceiling plate. 2-5. do not...fan comes with the pilot holes you drilled. 2 • Installing the Ceiling Plate CAUTION: To avoid possible electrical shock, before installing your fan, disconnect the power by turning...

Owner's Manual - Page 8

... Set Screw Canopy Canopy Trim Ring Low Profile Mounting Steps 3-5 - 3-6 Low Profile Screws Green Ground Wire Canopy Trim Ring Low Profile Washer Canopy Low Profile Screw Step 3-6 (Detail) Adapter Low Profile Screw Low...low profile mounting, the downrod is replaced with the hooks on one side of the pin in the ball. 3-3. Hanging the Fan: Note: To hang the fan, you must tilt the canopy to...

Owner's Manual - Page 9

... the black wire (ungrounded) from the fan • The black/white wire (ungrounded) from the fan to the wire (ungrounded) for the wall switch Single Switch Wiring: • The black wire (ungrounded) from the ceiling to the black (ungrounded) and the black/white wire (ungrounded) from the fan CAUTION: Be sure no bare wire or wire strands are not included. Turn the...

Owner's Manual - Page 10

... 5-5. Verify that must remain engaged while swinging the canopy for the following steps could cause the fan to the top of the canopy. Note: Should you use a magnetic tip screwdriver for alignment....5-3 Canopy Canopy Trim Ring Canopy Screw 10 42626-01 • 05/05/11 • Hunter Fan Company Partially install a canopy screw between the slots in the hanger ball. Align the tabs on ...

Owner's Manual - Page 11

... tightened. Attach each blade, insert one blade mounting screw through the blade iron, and attach lightly to secure shipping blocks. 6-4. Remove the blade mounting screws and rubber shipping bumpers from the motor. For each blade to the fan). 6-1. Insert the second blade mounting screw, then securely tighten both mounting screws. If you...

Owner's Manual - Page 12

... the light fixture, you are firmly situated in the switch housing and light fixture falling. 7-5. Turn the housing counterclockwise until the housing assembly screws are installing a light fixture.... to install the light fixture, proceed with this fan model. 7-1. Feed the upper plug connector through the center opening of installing the fan with an integrated light fixture assembly and ...

Owner's Manual - Page 13

...: In compliance with US federal energy regulations, this ceiling fan contains a device that restricts its light output. Steps 7-8 - 7-10 13 42626-01 • 05/05/11 • Hunter Fan Company Shade Bulb 7 • Completing Your Installation With or Without a Multi Staked Light Fixture (Cont.) 7-6. If lights do not appear to the upper switch housing Plug...

Owner's Manual - Page 14

... and are ready to install them into the empty switch housing included with the fan. Carefully place the capacitors in the light assembly housing.) 7-17. Remove the patented breakaway connector from the multi-wire connector. 7-16. Unplug the two-wire connectors; You have a black with Step 7-6. 14 42626-01 • 05/05/11 •...

Owner's Manual - Page 15

... dampened cloth. Restart fan. 8 • Operating and Cleaning Your Ceiling Fan 8-1. The fan pull chain controls power to cool the room with a furniture polishing cloth. The light pull chain controls power.... You may use upward air flow pattern To Change Airflow Direction Turn the fan off and let it come to the opposite position. A vacuum cleaner brush nozzle can remove heavier...

Owner's Manual - Page 16

... at our Web site at the wall switch. Turn power off suddenly, but fan is properly seated. fan does not move. 1. Push motor reversing switch firmly left or right to the light socket. 2. Turn the power to the wiring the fan section. 3. Loosen canopy, check all connections according to the fan off at http://www.hunterfan.com. Problem: CFL...

Parts Guide - Page 1

...Light bulb / Bulb Switch Housing, Alternate Cap, Switch Housing Plug Button Hardware Kit Blade Grommet Blade Assembly Screw Screw, Machine, 6-32 Wire Connector Screw, Switch Housing Assembly Balancing Kit Model # 20181 20182... Thumbscrew Screw, Machine, 6-32 Hanger Bracket Assembly Blade Assembly Switch Housing Assembly Fan Parts (Not Drawn to Scale) PARTS GUIDE Using this Parts Guide, make ...