Hoover UH70830 Support Question
Hoover UH70830 Support Question
Find answers below for this question about Hoover UH70830.Need a Hoover UH70830 manual? We have 1 online manual for this item!
Current Answers
Related Hoover UH70830 Manual Pages
Product Manual - Page 3
... Please enter the complete model and Manufacturing Code in the spaces provided. Verification of date of purchase may be required for warranty service of vacuum)
CONTENTS
Important Safety Instructions 3 Vacuum Assembly 5
Carton Contents... CODE
(Label located on back of your sales receipt to register by phone.
MODEL
MFG. only) or to register your product online at hoover.com.
Fri 8am...
Product Manual - Page 6
... by pulling on cord, or pull cord around sharp edges or corners. Do not allow plug to whip when rewinding (cord rewind available on select models only). • Unplug before connecting Powered Hand Tool. • Do not pick up flammable or combustible liquids, such as gasoline, or fine wood sandings, or...
Product Manual - Page 10
... ridges on right back side (C) of Powered Hand Tool and pivot into clip until instruction 1.3
1.2 Insert handle section into vacuum body first. 1. VACUUM ASSEMBLY
CARTON CONTENTS
A. Wand H. Dirt Cup
1.1
A
*Varies per model) Note: Remove the screw located in the vacuum base and set aside until secure.
1.6 Place Crevice Tool into Wand and slide into...
Product Manual - Page 11
...**
1
3. Stair Cleaning Handle
5
13
10. Furniture Guard
10
18. ON/OFF Switch 21.
To turn vacuum OFF,
push switch again.
!
When red tape is visible on select models only)
2.3 Grasp the end of cord reel. Actual model may vary from cord reel until red tape is almost fully extended. 2. Headlight*
19 20
11...
Product Manual - Page 14
... .
TOOLS
IMPORTANT
Brushroll continues to "Hard Floor" setting.
• Higher settings: for upholstered furniture, draperies, mattresses, clothing, and carpeted stairs. (Tool varies per model)
C. CAUTION ! WARNING
Unplug vacuum before connecting Powered Hand Tool. REMOVING HOSE
ATTACH WAND AND TOOLS
3.2
To remove hose for reaching hard to desired height setting. Tools allow for...
Product Manual - Page 15
...Tool (Tool varies per model) for clogging - STAIR CLEANING
3.4 Lift vacuum by an authorized service representative.
Attach the plug
end to continuing use and care of your vacuum will ensure continued cleaning...,
as proper use . DO NOT submerge in upright position.
! Never leave the vacuum standing on stairs. When using tools, always ensure handle is red: with a detergent...
Product Manual - Page 18
... into place. Clear obstructions if present. 4. Do not use vacuum without dirt cup or filters in place.
4.6
4.7
A
B
9 Actual model may seal the filter and cause a reduction in Fig. ... clean the filters often. Press firmly to remove Rinsable Filter. Do not use .
Place the vacuum in place. Unplug before removing the dirt cup.
4.2
!
To reduce the risk of personal...
Product Manual - Page 19
.... 10 Replace dirt cup as described in place. Actual model may take up to Clean
! Dry filter on edge so air circulates on vacuum. What to secure into position on both sides of the...11 4.10 Dirt and debris can be replaced more often to dry completely before replacing.
Do not use vacuum without dirt cup or filters in place.
4.9
A
4.10
Remove dirt cup as described in Fig 4.5....
Product Manual - Page 22
Lay vacuum down in hortizontal position with nozzle facing down as they can cause damage.
Replace bottom ...reduce the risk of injury from images shown. To lock back into place, push hose into locked position.
4.19 B 4.20
11 Actual model may vary from moving parts -
Remove (4) screws on either side of injury from brushroll (A).
4.16 Reposition nozzle plate cover and insert (4) ...
Product Manual - Page 23
...21 Using a Phillips screwdriver, remove (2) screws as in low position. With lettering on select models only)
!
HEADLIGHT: How to make sure belt is
not twisted. Unplug before servicing.
4....800944-9200.
IMPORTANT
Rotate brushroll manually to Replace
(available on
B
A
outside of the vacuum and should be checked from time to time to Buy: Headlight
Additional bulbs may vary ...
Product Manual - Page 26
... setting is incorrect.
1. Cord reel does not retract.
5. Dirt cup not installed correctly.
1.
Rinsable and/ or Filter made with HEPA media is difficult to tool.
2. Vacuum is dirty.
1. Too much pressure being cleaned -
smell detected 2. Replace brushroll belt - Any other servicing should , has been dropped, damaged, left outdoors, or dropped into...
Product Manual - Page 27
... Hoover® Warranty Service Dealer (Depot) by the complete model number when requesting information or ordering parts. (The model number appears on the bottom of authorized service outlet locations call 1-800-944-9200; Do not send your vacuum by :
• Checking the Yellow Pages under "Vacuum Cleaners" or "Household". • Visit our website at...
Similar Questions
Discontinued Model?
is the model ch83000 discontinued or why can't I find anywhere to purchase onlin
is the model ch83000 discontinued or why can't I find anywhere to purchase onlin
(Posted by Micahcarter63 10 months ago)
Replacing The Handle Release Pedal On Windtunnel Uh70830
Does anyone know how to replace the handle release pedal? Ours broke off. Got a replacement part but...
Does anyone know how to replace the handle release pedal? Ours broke off. Got a replacement part but...
(Posted by jlbrennan 9 years ago)
How Do You Gain Access To The Belt On The Hoover Uh70830?
There seems to be no way for me to get to the belt or belts if there's more than one. I don,t see an...
There seems to be no way for me to get to the belt or belts if there's more than one. I don,t see an...
(Posted by Anonymous-131935 10 years ago)
Hoover Elite Commercial Vacuum Model 1404
I have a Hoover Elite Commercial vacuum model 1404, what hose fits this?
I have a Hoover Elite Commercial vacuum model 1404, what hose fits this?
(Posted by chenriques 11 years ago)