Hoover U5180-910 Support Question
Hoover U5180-910 Support Question
Find answers below for this question about Hoover U5180-910 - Mach3 Cyclonic Upright Bagless Vacuum.Need a Hoover U5180-910 manual? We have 1 online manual for this item!
Question posted by jsmtca on October 18th, 2011
Broken Part Twice Front Whheel Cariage Part # 93001674
Hi, Bought this vacuum new, use once a month in a one bedroom apt. Not mis-used. the part broke once had to replace the part-- one side pin broke off. and then it broke again same place. This should be replaced by the company. if not I will not purchase it again, the part cost me about $12.00. I will buy a new vacuum. I am upset that I have to buy the same part twice and probably again soon.
Thanks for your time,
John Snowberger
Current Answers
Related Hoover U5180-910 Manual Pages
Manual - Page 1
®
Cyclonic Upright
®
Vacuum Cleaner
hoover.com
Owner's Manual
ENGLISH § pp. 1-12 ESPAÑOL § pág 13-20 FRANÇAIS § p. 21-27
This product was designed for easy assembly (see page 3)
Review this manual before operating the cleaner.
Manual - Page 2
... cleaner before connecting the powered hand tool. • Do not use without dirt cup or filters in place. hoo ero c
C EANER/A ITREA R/A IRA ORA
MO E...Replacing Agitator Brush Roll ........9 Replacing Belt 8-9 Replacing Powered Hand Tool
Agitator Brush Roll 10 Replacing Power Hand Tool Belt ..10 Replacing...with damaged cord or plug.
Do not allow vacuum cleaner to be present. • Avoid ...
Manual - Page 3
... orange tie wrap (A) and pull until the black plug (B) comes out of ends.
After the plug ends are connected, pull on plug to the store.
1. Use caution so as NOT TO CUT the black power cord. Discard the orange tie wrap. After ends are fully connected, the orange tie wrap (A) must...
Manual - Page 4
...and pow- Dirt cup assembly
21. Stair cleaning handle: to use .
To turn cleaner ON, push ON/OFF switch once. 1-6 B
A
Position tools
D
Place smaller diameter end of wand
(A) into bottom of carpet being
...Hose handle 14.
This plug will fit in upright position, tilt cleaner back on lever to install the proper outlet.
Headlight
Operate cleaner only at top.
Manual - Page 5
... to raise and lower the nozzle for various carpet pile heights, place handle in upright position and turn knob to the next higher setting.
• Higher...use the hose and power hand tool for all types of cleaner) as shown and will continue to prevent the cleaner from falling, always place it is lowered to the desired setting. Continued § 5 Move cleaner back to cleaner. upright...
Manual - Page 6
...from hose tube and reposition hose end into place.
6
Combination tool use when handle is in warm water with a detergent.
To replace brushes, align bottom of the above the ...the upright position. Use them with a damp cloth.
To use . Crevice tool may be used in tight spaces, corners and along edges in upright position.
Floor brush (available on some models only) use ...
Manual - Page 7
...Replace dirt cup as described in Fig. 3-2. Secondary filter
How to secure into cleaner body.
3-7
A B
C
Dirt and debris can be cleaned from electrical outlet. Do not operate cleaner without dirt cup or filters in place.
3-8
D
B A
C
Remove dirt cup as described in place. When using... § 7 Cleaning filters
Cyclonic filter assembly
How to empty
Disconnect cleaner from the filter assembly by...
Manual - Page 8
...replacement
The belt on either side of socket. Replace belt if it is stretched, cut or broken. Do not attempt to buy
When purchasing new filters, ask for 24 hours before replacing frame into socket until locked in Fig. 3-13. What to remove filter (B) from frame. Using... Removing hood Press handle release pedal and place handle in good condition. Using a coin, turn the two slots (A)...
Manual - Page 9
...new belt over motor pulley (B).
3-17
3-18
3-19
E
D
F
C
Replacing agitator brush roll Insert agitator through belt and place belt in "The belt" section to motor bearings.
Installing new...
Rotate hood toward front of agitator (E) into place. Removing agitator brush roll
Remove agitator brush roll and used belt. Discard used belt. G
Replacing hood Align tabs (F) on hood with slots (G)...
Manual - Page 10
... Remove belt from hose. Insert brush roll through the top of tool.
Replace with new belt.
8. Remove agitator including end plates (C) and discard. 4. The belt...gouged or broken, it so bottom faces up. Replace belt
When replacing belt, ask for HOOVER part No. 48414088.
3-21
A
3-22
B
2.
How to pinch brush bristles in tool housing and snap into place. 5. ...
Manual - Page 11
... Sales and Service Center or Authorized Hoover Warranty Service Dealer (Depot) by using tool applying light pressure.
• Blockage in turbine channel • Remove blockage.
• Broken or worn belt • Replace belt
• Low cleaner suction • Check items under "Vacuum Cleaners Household" OR • checking the list of Sales and Service Centers...
Manual - Page 12
... will be paid one of purchase will be due to place this warranty gives you specific legal rights, you , all...at no cost to you may be required before service is used in and turn ON. Hoover Sales and Service Centers.
2.... period.
Military Exchange. Proof of the following steps to state.
Replace belt, agitator and hood. If further assistance is purchased. Refer to...
Similar Questions
My Hoover Upright Bagless Vacuum's Suction Doesn't Work.
(Posted by ljbennion50 11 years ago)
Hoover U5180-910 Mach 3 Cyclonic Upright
How do you empty the contents when full?
How do you empty the contents when full?
(Posted by bobf537 12 years ago)
How To Switch From Using Floor Clean To Using Hose On Hoover Cyclonic Upright.
I got a hoover cyclonic upright bagless vacuum used with no instructions. Is there a way to switch t...
I got a hoover cyclonic upright bagless vacuum used with no instructions. Is there a way to switch t...
(Posted by mindy 12 years ago)
Hoover Cyclonic Upright Series U5180
It blew the house circuit breaker and now won't restart. It is not clogged and filters clean. I bypa...
It blew the house circuit breaker and now won't restart. It is not clogged and filters clean. I bypa...
(Posted by dmcgee 13 years ago)