Hoover FH40010B Support Question
Hoover FH40010B Support Question
Find answers below for this question about Hoover FH40010B.Need a Hoover FH40010B manual? We have 1 online manual for this item!
Question posted by selfsh77 on June 15th, 2011
Assembling The Spin Brushes
when I try to assemble the spin brushes, it says that the brushes "snap" in. I exchanged the 1st machine & the 2nd one still doesn't snap in. the clips that are supposed to hold the brushes in, do not. if the machine moves to much, they fall out. is this due to how the machine is made, or 2 bad machines?
Current Answers
Related Hoover FH40010B Manual Pages
Manual - Page 1
... or concerns? All rights reserved. #960009623 ID100507-R0
página E1
FloorMate™ SpinScrub® Hard Floor Cleaner
www.hoover.com
IMPORTANT: READ CAREFULLY BEFORE ASSEMBLY AND USE. Owner's Manual
Operating and Servicing Instructions
Español -
Manual - Page 2
... Sequence 10 Cleaning Floors 10 Picking Up Spills 10 Maintenance...11 Nozzle...11 Brushes...12 Storage...12 Lubrication...12 Troubleshooting...13 Service...14 Cleaning Products...15 Warranty...16... under cleaner)
Contents
Important Safeguards 3 Cleaner Assembly...5
Carton Contents 5 Attach Handle...5 Install Brushes and Nozzle 5 Unfold Handle...6 How to this product to speak with ...
Manual - Page 3
...openings. Keep cord away from heated surfaces. • Always disconnect cord from openings and
moving parts. • Do not pick up chlorine bleach, drain cleaner, gasoline or any time...clean over cord. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS
When using recommended chemicals with this machine, be present. • Avoid picking up operation. • Close supervision is ...
Manual - Page 4
...conductor (C) and grounding plug (A). The plug must be used to connect this machine.
Do not expose machine to freezing temperatures. • Do not use with a qualified electrician or ...chemicals used with all local codes and ordinances. tion. This appliance is for machine applica- • Do not use a flammable or combustible liquid to whether the outlet...
Manual - Page 5
... cleaner. Align middle section (D) of nozzle.
1.6
DE C
1.7 While holding nozzle in place, slide latches inward to lock in place.
1.3
C D B
1.5
1.7
5 NOTE: Phillips screwdriver needed for assembly. Attach handle
1.2 Rotate bottom handle support (A) up to snap into hole.
1.5 Press brush assembly firmly to the upright position until a snap is felt.
1.3 Align control rod (B) on the
floor...
Manual - Page 6
ON/OFF Switch 3. Mode Selector Dial: turns brushes
3
ON for wet washing and OFF for household use.
18. Clean Water Solution Tank
5
...pedal (A) to lower handle to turn cleaner ON. Upper Handle Release Button
This cleaner is intended for
drying and vacuuming
5. Push switch again to operating position. HOW TO USE
Cleaner Description
1. Clean Water Solution Tank
Release
6
8. ...
Manual - Page 7
...section for complete cleaning instructions.
2.6
2.7
A
VACUWUAMSDHRY
7
In this position, the brushes will not rotate and are raised off .
2.7 For dry debris pickup, turn...Mode selector dial (A) turns the brushes on and off the floor surface. Refer to "How to the WASH position.
For wet pickup, turn the dial to the VACUUM position.
Transporting
2.4. To move your cleaner from room to the ...
Manual - Page 8
The Clean Water Solution Tank holds detergent and water that can normally be dispersed onto the surface being cleaned. Rotate cap clockwise until latch snaps in place.
2.8
2.10
2.12
E
2.14
! CAUTION !
Fill tank to Fill
Place carpet cleaner handle in place. DO NOT use one cup (2 oz.) HOOVER® Hard ...
Manual - Page 9
... outlet. Replace lid onto Dirty Water Tank, pressing down firmly until snapped in place.
Dirty Water Tank (lower tank)
Automatic "Shut Off"... and must be cleaned by tapping the filter or gently brushing using your hand. Dry or loose debris will change. The...is low or reduced.
2.17
How to be emptied after dry vacuuming and before wet operation. Check the Clean Water Solution Tank also....
Manual - Page 10
... The cleaner's suction will provide light agitation to the VACUUM position. Repeat cleaning motion. The Mode selector dial turns the brushes on handle release pedal and lower handle to WASH position...To greatly enhance drying of these conditions exist. Ensure that have been sealed with water. Simply move the Mode selector dial between wet cleaning and wet pickup, it is a loss of suction...
Manual - Page 11
... and release the trigger. MAINTENANCE
Familiarize yourself with removable brushes for easier assembly of your cleaner will ensure continued cleaning effectiveness.
Align ...holding nozzle in place, slide latches inward to lock in the upright position for easy cleaning.
! CAUTION !
Cleaner should be in place.
4.1
A
4.3
4.5
4.2
B A
4.4
EF D
C D
11 Remove debris from moving...
Manual - Page 12
...; Do not store cleaner on cleaner.
4.10 While holding nozzle in place, slide latches inward to lock in the upright position.
Remove nozzle.
How to Replace
4.8 To replace brushes, align post (C) on brush block with hole (D) on floor.
4.7 Push two brush release buttons (B) and remove the brush assembly. Replace nozzle, making sure latches (E) are out. Set...
Manual - Page 13
... recommended detergents to reduce foaming.
2. Dirty Water Tank not in place.
3. Make sure Filter and Filter lid are locked in place. Cleaner solution won't dispense
Brushes won 't run
1. Check fuse or breaker in home. Wrong detergent used.
1. Empty dirty water tank. Check fuse or breaker in home. Dirty Water Tank full...
Manual - Page 14
... This will only result in Glenwillow for service. Do not send your vacuum by :
• Checking the Yellow Pages under "Vacuum Cleaners" or "Household". • Visit our website at hoover.com (U.S....AB T5W 2P2, Phone: 1-800-263-6376, Mon-Fri 8am-7pm EST. Always identify your vacuum to find the service outlet nearest you need further assistance: To speak with a customer service ...
Manual - Page 15
...: pollen, pet dander, dirt, and dust.
2 When cleaning a hard surface, the Hoover® hard surface attachment below must be used (optional if not included): 5 Brush/Dual Brush Hoover® part # 48417008. ClLeEaAnNiInNG pPrRoOdDuUCtTsS
WARNING: To reduce the risk of fire and electric shock due to internal component damage, use only Hoover®...
Manual - Page 16
...NEGLIGENCE, TORT OR STRICT PRODUCTS LIABILITY OR ARISING FROM ANY CAUSE WHATSOEVER. 8. Military Exchanges and Canada.
This warranty does not cover pick up, delivery, transportation or house...OR visit Hoover® online at www.hoover.com. However, if you specific rights; Military Exchange and outside a U.S. ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR ...
Similar Questions
Is The Clip That Holds The Nozzle To The Vacuum Cleaner Repairable
(Posted by Taylorspecialk 1 year ago)
Hoover Fh40010b Floormate Spinscrub Wet/dry Vacuum Won't Stay On.
Floormate keeps shutting off. I checked all the seals and cleaned everything, but it still shuts off...
Floormate keeps shutting off. I checked all the seals and cleaned everything, but it still shuts off...
(Posted by 0rosie 10 years ago)
What Brands Of Cleaning Solution Are Safe To Use In A Hover Fh40010b ?
I just purchased a Hoover FH40010B floor cleaner and want to know what other brand names of cleaning...
I just purchased a Hoover FH40010B floor cleaner and want to know what other brand names of cleaning...
(Posted by gbalbach 10 years ago)
How Do You Remove Handle On Hoover Spin Scrub Fh40010b
The handle snaps in place when installing. But I need to know how to take it back off.
The handle snaps in place when installing. But I need to know how to take it back off.
(Posted by jim606 12 years ago)
Spin Brushes Stopped Spinning. Is There A Belt Which Needs To Be Replaced?
(Posted by RYurchak 12 years ago)