Honeywell T4700 Support Question
Honeywell T4700 Support Question
Find answers below for this question about Honeywell T4700.Need a Honeywell T4700 manual? We have 1 online manual for this item!
Question posted by kathiethornton on February 16th, 2014
Honeywell T4700 Overload
The thermostat has been functioning fine for the past four years and there have been no changes to the electrical system in the house, but now it shuts itself off and we get an overload message on the thermostat. I have reset it and it seems to run fine for hours, then shuts off in the middle of the night. What should I be looking for?
Current Answers
Related Honeywell T4700 Manual Pages
Owner's Manual - Page 1
All Rights Reserved
69-1396-2 T4700 Chronotherm™ Electronic
Programmable Line Voltage Thermostat
OWNER'S GUIDE
® U.S. Registered Trademark Copyright © 2003 Honeywell International Inc.
Owner's Manual - Page 2
... 29 percent of the energy used to heat a controlled zone.
• Offers up to a 12 percent energy saving during comfort periods compared with conventional bimetallic electric heating thermostat, according to the Electric Power Research Institute.
69-1396-2
2
Owner's Manual - Page 3
... you to awake (or return home) to Honeywell Customer Assistance at 1-800-468-1502. When you with your home. Your new T4700 Chronotherm™ Programmable Electronic Line Voltage Thermostat is designed to Another Day ....... 9 Overriding a Program 10 Programming Additional Functions ........ 10 Checkout 12 Troubleshooting 12 Customer Assistance 13 One-Year Limited Warranty 14
3
69-1396...
Owner's Manual - Page 4
... mm) stranded copper
leadwires, suitable for connection to 95 percent
RH, non-condensing.
Switching: Patented CoolSwitch®.
69-1396-2
4 Factory set at 240V, 60 Hz. Electrical Ratings (Noninductive):
3800W, 16A maximum; 500W, 2A minimum at 16°C (61°F). makes heating circuit on temperature fall . Humidity Ratings: 55 to aluminum wiring...
Owner's Manual - Page 5
... and then undergoes a self-test - Table 1.
the internal checkout is complete and the thermostat is turning on the baseboard heater, press the (+) key until the setpoint displayed exceeds the...schedule for warmth in the display.
while 00E displays for 7-days. Programming Thermostat
Initial Powerup
When the thermostat is followed by the display flashing (1:00 PM); The (°) symbol is...
Owner's Manual - Page 6
...can set for an energy-saving temperature while you get up. This resets only the clock; The thermostat is the time the thermostat turns on the equipment after an energy saving period. When deciding what... is complete, the device reverts to the (+) key with you arrive home.
Thermostat Reset
The T4700 can be programmed to program your lifestyle. Four time periods are away at work...
Owner's Manual - Page 7
Setting the Current Day and Time. Press This Key
Display Shows
Description Displays day of the week.
2
Displays changed day of the week.
3
Displays hour of the day.
4
Displays changed hour of the day.
5
Displays minute of the day.
6
Displays changed minute of the
day.
7
69-1396-2 Step 1
Table 2.
Owner's Manual - Page 8
... time in
ten-minute increments.
4
Displays WAKE setpoint
temperature.
5
Displays changed WAKE setpoint
temperature.
6
Displays LEAVE time.
NOTE: Continue through the display shows the first day to program, beginning with Monday. To easily copy one day ...
Owner's Manual - Page 9
... display reverts to Run mode, or 2) during the programming session, after five minutes elapsed time with no program change any of the programmed steps. Copying Schedules to be copied; Simply keep pressing the Prog key until you arrive at the desired mode.
9
69-1396-2
...
Owner's Manual - Page 10
...the HOLD temperature.
Hold (HOLD) Mode
Changes to TEMPorary mode and controls at the HOLD temperature indefinitely.
Table 5. Changes from the HOLD mode to 7-day or ...Key Display Shows
Description
Temporarily Overriding a Program
Temporary (TEMP) Mode
Indefinitely Overriding a Program
Changes to HOLD mode and controls at a new temperature until the next scheduled event (for ...
Owner's Manual - Page 11
... both the Prog and Func keys. Press Prog key a second time to Run mode.
Convert 5-1-1 to 51-1 programming). Press (+) key to change any of the programmed steps.
Programming Additional Functions. Initially a random fourdigit/letter display occurs (for three seconds and the display returns to Run mode, or 2) during the programming session, after...
Owner's Manual - Page 12
... complete, the display flashes (1:00 PM) and the thermostat is turning on the baseboard heater.
2. Display Code Oload
Cause
Connected load exceeds 3800W.
06E
Power failure
detected. Push Reset key to clear and reset clock.
Push Reset key to clear and reset clock.
If problem persists, call Honeywell Customer Response Center at 1-800-468-1502.
69...
Owner's Manual - Page 13
Central time.
13
69-1396-2 Customer Assistance
Please direct any questions about the operation of this thermostat to Honeywell Customer Assistance at 1-800-468-1502, Monday-Friday, 7:00 a.m. - 5:30 p.m.
Owner's Manual - Page 14
... from which occurred while the product was in the workmanship or materials, under normal use and service, for a period of one (1) year from defects in the possession of a consumer. Honeywell's sole responsibility shall be free from the date of purchase by damage which you .
69-1396-2
14 If, at any time during...
Owner's Manual - Page 15
... A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you may have any questions concerning this warranty, please write Honeywell Customer Assistance Center, 1985 Douglas Dr, Golden...
Owner's Manual - Page 16
Rev. 1-03
Printed in U.S.A.
Automation and Control Solutions
Honeywell International Inc. on recycled paper containing at least 10% post-consumer paper fibers. www.honeywell.com/yourhome Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North
35 Dynamic Drive
Golden Valley, MN 55422
Scarborough, Ontario
M1V 4Z9
69-1396-2 G.H.
Similar Questions
Honeywell Thermostat Wont Run Fan In Auto
(Posted by triTerr 9 years ago)
Honeywell Tb8220u I Cannot Get The Thermostat To Run The Sunday Program.
Everytime I set the Sunday program the system uses the Saturday setttings instead. Any suggestions?
Everytime I set the Sunday program the system uses the Saturday setttings instead. Any suggestions?
(Posted by travismuse 10 years ago)
My Thermostat Functions Fine But There Is A Clicking Noise That Occurs On And Of
(Posted by mcgrath2005 11 years ago)
I Have No Manual And Do Not Understand How To Operate
Trying to turn on heat with Honeywll Thermostat T4700B1014
Trying to turn on heat with Honeywll Thermostat T4700B1014
(Posted by Thommy 12 years ago)