Honeywell RTH7600 Support Question
Find answers below for this question about Honeywell RTH7600.Need a Honeywell RTH7600 manual? We have 3 online manuals for this item!
Question posted by ensunbu on June 16th, 2014
How To Wirea Honeywell Rth7600 To A Heat Pump With Electric Back Up /old System
has 8 wires
Current Answers
There are currently no answers that have been posted for this question.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Be the first to post an answer! Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.
Related Honeywell RTH7600 Manual Pages
Owner's Manual - Page 2
It is Easy
Label wires and remove your old thermostat
Install and wire your new thermostat
Set your new thermostat to match your heating/cooling system
- Installation is preset for wiring assistance before returning the thermostat to the store.
69-2206EF-01
ii Call 1-800-468-1502 for the most common system
We are here to help. This thermostat works with virtually all System Types
-
Owner's Manual - Page 4
Leave wallplate in place
Is there a sealed tube containing mercury? Old thermostat
Cover
69-2206EF-01
M28099 2 Remove Old Thermostat
Remove old thermostat but leave wallplate with wires attached.
If so, see back cover for proper disposal instructions.
Owner's Manual - Page 8
.... Labels don't match? Have a Heat Pump system? Call 1-800-468-1502 for wiring assistance.
69-2206EF-01
We are here to help.
See pages 22-23.
CONVENTIONAL
SCREW
INSERT WIRES THEN TIGHTEN SCREWS
LABELED WIRES CONVENTIONAL
WIRE HOLE
C
W2
WY G
G
Y2
Y
W
RC
R
R
M28070
Remove metal jumper if you have both R and Rc wires. 6 Connect Wires
Simply match wire labels.
Owner's Manual - Page 13
...match your thermostat to your system type. *Heat Pump-an air conditioner that provides cooling in the summer, and also runs in reverse in the winter to provide heating. If your... you 're done!
11 If your system type is :
q Multistage Heat and Cool q Heat Pump* without Backup Heat q Heat Pump* with Backup Heat q Heat Only q Cool Only
Continue with advanced installation
on 120/240 Volt systems...
Owner's Manual - Page 18
... air condi- tioning only.
7 Heat pump: Heat pump with central air condi-
ASSISTANCE
TROUBLESHOOTING
69-2206EF-01
16 SETUP
WIRING
Advanced Installation Guide
ASybsotuetmyosuertunpew thermostat
See page 14 to select your system
Type
type:
1 Heat/cool: Gas, oil or electric
heating with
backup or auxiliary heating.
8 Heat/Cool Multiple stages:
2 heat stages (wires on W and
W2...
Owner's Manual - Page 19
... system (system controls fan operation). 1 Electric heat: Use this setting if you have an electric heating system (thermostat controls fan operation).
0190 Heat Pump Press s/t to select whether your Changeover changeover valve is used in heating Valve (for heat or cooling: pumps only) 0 Cooling changeover valve: Use this setting if you connected a wire labeled "O" to the O/B terminal (see page...
Owner's Manual - Page 20
...
WIRING
Advanced Installation Guide
ASybsotuetmyosuertunpew thermostat
See page 14 to select your heating system: 9 Electric furnace: Electric
heating systems. 5 Gas or oil furnace: Standard
gas/oil furnace (less than 90% efficiency). 3 Hot water or high-efficiency furnace: Hot water system or gas furnace (more than 90%
efficiency).
1 Gas/oil steam or gravity
system: Steam or gravity heat...
Owner's Manual - Page 21
... to daylight
saving time (for areas that do not use the new 2007 DST calendar). Automatically turns on Heat or Cool based on room temperature.
ASSISTANCE
TROUBLESHOOTING
19
69-2206EF-01 SETUP
WIRING
ASybsotuetmyosuertunpew thermostat
RTH7600
See page 14 to daylight saving time (2007 and beyond, for areas that use the new 2007 DST...
Owner's Manual - Page 23
...
M28076
21
69-2206EF-01 If your old thermostat had 2 C or C1 wires, wrap each separately with electrical tape and do not match terminals, connect wires as shown here (see notes, below). Connect the R wire to the Rc terminal, and the RH wire to the C terminal.
SETUP
AWbiroiuntg-yocuornnveewnttiohnearml soyssttaetm
RTH7600
Alternate wiring (conventional systems)
If labels do not...
Owner's Manual - Page 24
... Aux do not match letters on new thermostat.
2.
Push any excess wire back into hole, then tighten screws.
3. SETUP
WIRING
Advanced Installation Guide
AWbiroiuntg-yohuerantepwumthpermostat
Connect wires: Heat Pump
1. SCREW
INSERT WIRES THEN TIGHTEN SCREWS
LABELED WIRES
HEAT PUMP
WIRE HOLE
HEAT PUMP
C
Aux
Aux
OYG
G
E
Y
L
O/B
RC
R
R
M28104
ASSISTANCE
TROUBLESHOOTING...
Owner's Manual - Page 25
SETUP
WIRING
Wiring-heat pump
RTH7600
Alternate wiring (for help .
If L terminal is used, C terminal wire must be
5 connected (contact a contractor if there is attached to the C terminal, stop now and contact a qualified contractor for help . If your old thermostat had separate O and B wires, attach the B wire to each have a wire
6 connected, use a small piece of wire to connect
them ...
Owner's Manual - Page 27
... Function 0190: Heat Pump sues cool air in cool (see page 17). ing system does Make sure the temperature is set lower
than the Inside temperature.
Make sure the temperature is on the screen
Compressor protection feature is closed
securely.
mode
ASSISTANCE
TROUBLESHOOTING
25
69-2206EF-01 SETUP
WIRING
Troubleshooting
RTH7600
Heating or cool- Make...
Owner's Manual - Page 30
... a sealed tube. US Patent No. 6,595,430; 7,114,554; 7,274,972; 7,225,054 and other patents pending. © 2008 Honeywell International Inc. 69-2206EF-01 M.S. 06-08
Registered Trademark. Contact your old thermostat in the trash if it contains mercury in U.S.A. Perchlorate Material-special handling may contain Perchlorate material. on recycled paper containing...
Operation Manual - Page 2
.... For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502
Read and save these instructions.
® U.S.
This manual covers the RTH7600 model.
(Pull thermostat from wallplate and turn over to find model number) This thermostat contains a Lithium battery which may apply, See www...
Operation Manual - Page 5
RTH7600
This thermostat is ready to go ! Set clock See page 6 2. Your new thermostat is set the time and day.
Then check the settings below and change , see page 7 3. Program schedules: Preset to energy-saving levels
while you're... at 6 am, leave at 8 am, return at 6 pm and go to do is pre-programmed and ready to go . Select fan setting: Preset to Heat To change if needed:
1.
Operation Manual - Page 7
... AM
Fan Auto
Set To
75
Heat On
Temperature setting
System setting (see page 8)
System & Fan
Schedule
Clock & Mode
Fan setting (see page 7)
M27526
Other display messages: • Cool On: Cooling system is activated • Heat On: Heating system is activated • Aux Heat On: Auxiliary heating system is activated (heat pump systems only)
5
69-2207ES-05
Operation Manual - Page 10
... system. • Auto: Thermostat automatically selects heating or cooling depending on how your thermostat was installed.
8 Note: The Auto and Em Heat system settings may not appear, depending on the indoor temperature. • Off: All systems are off. • Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat.
Compressor is locked out.
Operation Manual - Page 17
... compressor damage, do not use Auto Changeover if the outside temperature drops below 50°F (10°C).
15
69-2207ES-05 RTH7600
Auto Changeover
If the cool temperature is lowered to where it gets close to the heat setting, an arrow next to heat will show the thermostat is increasing to maintain a 3-degree separation.
Quick Start Guide - Page 1
...169; 2012 Honeywell International Inc. 69-2721-01 M.S. 05-12 Printed in place
Is there a sealed tube containing mercury? Quick Start Guide
Touchscreen Programmable Thermostat
RTH7600 Series
69-2721-01
5 Mount Wallplate
Mount the new wallplate using the supplied wire labels as you disconnect them, then remove the old wallplate.
2 Remove Old Thermostat
Remove old thermostat but leave wallplate...
Quick Start Guide - Page 2
....
0320 Temperature Format 0 Fahrenheit
(°F/°C)
1 Celsius
0330 Daylight Saving Time 0 Off: No adjustment for help .
5
If your old thermostat had 2 C or C1 wires, wrap each have an electric heating system (thermostat controls fan operation).
0190 Heat Pump
0 Cooling changeover valve: Use this setting if you must be connected
5 (contact a contractor if there is on and off to...
Similar Questions
Honeywell Rth7600 Thermostat Does Not Turn On Heat Pump
(Posted by wisgriff 10 years ago)
How To Wire Honeywell Rth7600 Thermostat For Heat Pump
(Posted by YOLOst 10 years ago)
Any Advice On Where To Connect A W2 Wire From An Old Thermostat For A Heat Pump?
I'm using this model to replace an old mercury thermostat. We have a heat pump system that services ...
I'm using this model to replace an old mercury thermostat. We have a heat pump system that services ...
(Posted by gkendall73 11 years ago)
When The Thermostat Stops Working Will The Unit, Ac/heat Pump, Stop Also.
The thermostat went blank and nothinf responds; the fan, ac, nor heat pump, will work.
The thermostat went blank and nothinf responds; the fan, ac, nor heat pump, will work.
(Posted by jimbodawg 12 years ago)