Honeywell RTH7000 Support Question
Honeywell RTH7000 Support Question
Find answers below for this question about Honeywell RTH7000.Need a Honeywell RTH7000 manual? We have 1 online manual for this item!
Question posted by Bobneuman59 on September 14th, 2012
Right Side Temperature Setting Side Is Blank? Heat Is Off.
The right side of the thermostat reading is blank. The heat is off and i cannot increase it because the thermostat cannot be temporarily increased. I put 2 fresh batteries but no change. Any suggestions? Thanks
Current Answers
Related Honeywell RTH7000 Manual Pages
Owner's Manual - Page 2
... Material-special handling may contain Perchlorate material. Registered Trademark. Patents pending. Need Help? All rights reserved. This manual covers the RTH7400 and RTH7500 models.
(Pull thermostat from wallplate and turn over to find model number) This thermostat contains a Lithium battery which may apply, See www.dtsc.ca.gov/hazardouswaste/perchlorate
CAUTION: EQUIPMENT DAMAGE HAZARD...
Owner's Manual - Page 3
... to status display 5
Programming & Operation Clock setting 6 Fan setting 7 System setting 8 Using program schedules 9 Program schedule overrides 13 Auto Changeover 15 Filter reminder 17 Special features 18
RTH7400/RTH7500 Series
Appendices Battery replacement 19 Customer assistance 20 In case of difficulty 21 Limited warranty 23
This thermostat is pre-programmed and ready to go...
Owner's Manual - Page 4
...comfort control keeps temperature within 1°F of the level you set. • Change/check reminder ...lets you many years of reliable service and climate control.
It has been designed to give you know when to replace furnace filter. • Large display with backlight is easy to -use thermostat. You've just purchased the world's most advanced, easy-to read...
Owner's Manual - Page 5
... go ! Program schedules: Preset to go . Select fan setting: Preset to Heat To change if needed:
1.. RTH7400/RTH7500 Series
Your new thermostat is set the time and day. Set clock See page 6
2.. This thermostat is ready to energy-saving levels while you're at any time, and manually adjust the temperature (see pages 13-14).
3
69-2222EF-03
Owner's Manual - Page 6
Schedule Press to set program schedule (see pages 11-12).
69-2222EF-03
4
M28426
Clock & More Press to set clock (see page 8).
System & Fan Press to make selections from screen menus. Operating Manual
Quick reference to controls
Arrow buttons Press to adjust temperature (see pages 11-14), or to select fan operation (see page 7) or system (see page 6) or furnace filter reminder.
Owner's Manual - Page 7
... page 8)
Mon
75 Recovery System Cool
6:01 AM
Fan Auto
Set to
75
Heat On
System & Fan
Schedule
Clock & Mode
Temperature setting
Fan setting (see page 7)
M28078
Other display messages: • Cool On: Cooling system is activated • Heat On: Heating system is activated • Aux Heat On: Auxiliary heating system is activated (heat pump systems only)
5
69-2222EF-03
Owner's Manual - Page 9
Fan setting
Press SYSTEM & FAN
System & Fan
Schedule
Clock & More
M28081
Press FAN to select mode, then press DONE
RTH7400/RTH7500 Series
Press SYSTEM & FAN, then FAN to select fan operation:
• On: Fan is always on. • Auto: Fan runs only when the heating or
cooling system is on. System Heat
System
Fan Auto Fan
Done
M28082
7
69-2222EF-03
Owner's Manual - Page 10
Compressor is locked out. Note: The Auto and Em Heat system settings may not appear, depending on the indoor temperature. • Off: All systems are off. • Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat. Operating Manual
System setting
Press SYSTEM & FAN
System & Fan
Schedule
Clock & More
Press SYSTEM to select mode, then...
Owner's Manual - Page 12
...settings, since they can reduce your heating/cooling expenses by as much as 33%. (See next page to adjust times and temperatures of each time period.)
Wake (6:00 am)
Leave (8:00 am)
Return (6:00 pm)
Sleep (10:00 pm)
Heat (Mon-Fri) Cool (Mon-Fri) Heat... 82 °
69-2222EF-03
10 Operating Manual
Energy saving settings for maximum cost savings
This thermostat is pre-set with energy saving program...
Owner's Manual - Page 13
... TUE WED THU FRI
Go Back
Period
6:00 Wake AM
M28085
Set to highlight Mon-Fri (they will share the same settings).
3. Press SELECT DAY to
62 Heat
Next Step
Done
1. Press NEXT STEP, then s or t to save & exit. Repeat steps 3-5 to set Heat temperature for selected days.
4. M28086
Select day(s) Select time Select temp
11...
Owner's Manual - Page 14
... is flashing, then press SELECT DAY.)
8. Repeat steps 1-6 to save & exit. Press NEXT STEP twice, then press s or t to set Cool temperature for this time period.
6. Press NEXT STEP, then s or t to set Heat temperature for this time period.
5.
M28086
Select day(s) Select time Select temp
69-2222EF-03
12 Operating Manual
To adjust program...
Owner's Manual - Page 15
The new temperature will temporarily override the temperature setting for the current time period. When the timer expires, the program schedule will resume and set the temperature to immediately adjust the temperature.
Program schedule override (temporary)
RTH7400/RTH7500 Series
Mon
62
System Heat
System & Fan
Adjust temperature
Temporary Set to
68 6:08 AM Heat On
Fan Auto
Use ...
Owner's Manual - Page 16
...
69-2222EF-03
14 This will be maintained 24 hours a day, until you manually change it, or press USE SCHEDULE to adjust temperature, then press HOLD. Operating Manual
Program schedule override (permanent)
Mon
62
System Heat
Adjust temperature
Set to
6:08 AM 68
Fan Auto
Permanent Hold
Hold
Cancel
Press s or t to cancel "Hold" and...
Owner's Manual - Page 17
... select between the cool and heat settings.
For example, if the heat temperature is raised to where it gets within 3-dgrees of the cool setting, the display will also show the thermostat is in the Auto mode, if a schedule override takes place (temporarily or permanently) the thermostat will automatically adjust the cooling and heating settings to maintain a 3-dgreee separation. RTH7400...
Owner's Manual - Page 18
...Auto Heat
Temporary Set To
74 Heat Cool
System
Hold
Cancel
M27486
The triangle indicates the cool temperature is lowering the heat setting down to maintain 3 degrees between heat and cool settings. Operating Manual
AubtooutCyhoaunrgneeowvetrhermostat
If the cool temperature is lowered to where it gets close to the heat setting, an arrow next to heat will show the thermostat is increasing...
Owner's Manual - Page 19
...
Set to
6:01 AM 70 Heat On
System
Fan Auto Heat
Reset
Schedule
Clock & More
M28089
Press MORE to reset reminder interval
60
Days
Reset
Next
Done
If activated during installation, the furnace filter reminder alerts you when it expires: 1. Press DONE to restart the timer. AFibltoeurtryeomuirndnewr thermostat
RTH7400/RTH7500 Series
Press RESET after changing...
Owner's Manual - Page 20
... allows the thermostat to "learn" how long the furnace and air conditioner take to reach programmed temperature settings, so the temperature is reached at the time you wake at least 3 degrees apart.
When the system is used in climates where both air conditioning and heating are used on screen. The heat will automatically adjust settings to maintain...
Owner's Manual - Page 21
... than a month. Even if the warning does not appear, you should replace batteries once a year, or before batteries are optional (to provide backup power) if your thermostat was wired to remove from wallplate
M28103
Batteries are depleted. Insert 2 fresh AA alkaline batteries
M28101
19
69-2222EF-03
Install fresh batteries immediately when the LO BATT warning begins flashing.
Owner's Manual - Page 23
... you have difficulty with your thermostat, please try the following suggestions. Display is blank
• Check circuit breaker and reset if necessary. • Make sure power switch at heating & cooling system is on. • Make sure furnace door is closed securely. • If thermostat is battery powered, make sure fresh AA alkaline
batteries are set to acceptable ranges:
key...
Owner's Manual - Page 24
... 18).
69-2222EF-03
22 Wait 5 minutes for the system to Cool. Make sure the temperature is set
cooling system
higher than the Inside temperature.
• Check circuit breaker and reset if necessary.
• Make sure power switch at heating & cooling system is on.
• Make sure furnace door is closed securely.
• If...
Similar Questions
Problems With The Rth7000 Working Our New 2 Stage Furnace. Doesn't Maintain Heat
(Posted by rick78358 11 years ago)
Our Thermostat Will Not Us Set Our Heat Seating Higher Than 68 Degrees. Help?
How canI "unlock" my thermostat so that I can turn the heater up higher than 68 degrees? We have a H...
How canI "unlock" my thermostat so that I can turn the heater up higher than 68 degrees? We have a H...
(Posted by morgans2004mom 11 years ago)
Why Is Thermostat Temperature Set 5 Degrees Higher Than Required
(Posted by perhar71 11 years ago)