Home » Honeywell » Thermostats » Honeywell RTH2310B

Honeywell RTH2310B Support Question

Find answers below for this question about Honeywell RTH2310B.
Need a Honeywell RTH2310B manual? We have 1 online manual for this item!

Honeywell Overview Questions Manuals Reviews Videos Research

Question posted by jmgartist on June 27th, 2019

Air Condition

How do I manually set air conditioning on:Honeywell RTH2310BI do not want to program it.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by Odin on June 27th, 2019 9:02 AM

This answer was accepted by the poster of the original question.

Odin

Member since:
April 10th, 2010

Points: 41,236,670

1,100
points

See the 2 manual pages starting at https://www.manualslib.com/manual/555417/Honeywell-Rth2310.html?page=16#manual. If the issue persists or if you require further advice, you'll have to consult Honeywell: use the contact information at https://www.contacthelp.com/honeywell/customer-service.

Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.

Related Honeywell RTH2310B Manual Pages

Owner's Manual - Page 1

Quick Installation Guide RTH2310 Programmable Thermostat 69-2214EF-04

Owner's Manual - Page 2

... instructions in the following pages. 1) Identify your system type. 2) Remove your old thermostat. 3) Identify the wires. 4) Mount the new wallplate. 5) Connect the wires. 6) If the wire labels don't match. 7) Specify the furnace type. 8) Install the batteries. 9) Install the thermostat. 10) Set the system. Call 1-800-468-1502. 1 Do you need assistance? Quick Installation...

Owner's Manual - Page 3

... not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502. This thermostat is compatible with the following systems: • Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems. 2 RTH2310 Programmable...

Owner's Manual - Page 4

... the trash if it contains mercury in a sealed tube. Quick Installation Guide 2 Remove Old Thermostat 2. 1) Turn power off at the heating/cooling system. 2) Remove old thermostat, but leave wallplate with wires attached. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal. 3 Do not ...

Owner's Manual - Page 5

...the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your old thermostat or are labeled. Do not use C or C1 wires Identify and label each of these wires with electrical tape, so it cannot ... screw designations to prevent them from falling though the wall opening. 4 If any wires are not attached to your new thermostat.

Owner's Manual - Page 6

Insert plastic anchors. Pass wires through opening of wallplate and secure wallplate to the wall using provided screws. 5 Quick Installation Guide 4 Mount New Wallplate 4. 1) Remove coverplate. 2) Loosen screw (the screw remains captive on wallplate). 3) Remove thermostat. 4) Mark and drill appropriate mounting holes (or use existing holes).

Owner's Manual - Page 7

... with the terminal having the same letter. 2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws. 3) Push any terminal on the thermostat, see next page. 6 RTH2310 Programmable Thermostat 5 Connect Wires (typical wiring) 5. Labels don't match?

Owner's Manual - Page 9

J2 jumper HG Leave the jumper in this position if you have an electric furnace. 8 Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. RTH2310 Programmable Thermostat 7 Specify Furnace Type 6. HE Place the jumper to the G terminal.

Owner's Manual - Page 10

... the battery cover. It is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The thermostat will hear a clicking sound. By default, the setpoint is installed on the wall. Afterwards, the screen displays the actual temperature. Quick...

Owner's Manual - Page 11

RTH2310 Programmable Thermostat 9 Install thermostat 8. 1) Mount the thermostat on the wallplate. 2) Tighten the screw and install the coverplate. 3) Turn power back on at the heating/cooling system. 10

Owner's Manual - Page 12

... 2 See page 3 of Operating Manual. 3 Use the system switch to the next function, briefly press both and buttons simultaneously. 3) To change the setting, press the or button. Quick ...3 2, 3, 4, 5 or 6 4 Cooling cycles per hour 3 2, 3, 4, 5 or 6 5 1 Default settings are as follows: 2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-efficiency furnace), 4=15 min (gas or...

Owner's Manual - Page 13