Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by spraver on November 2nd, 2011
I Can't Get The Battery Cover Off! Is It Hinged From Top Or Bottom?
I am afraid I will snap off something and won't be able to replace the cover. Any help would be great.
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type. Install the batteries. Install the thermostat.... Set the system. Quick Installation Guide
Installation is Easy
Your new thermostat has been ...
Owner's Manual - Page 3
RTH2310 Programmable Thermostat
Identify System Type
1. This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502.
This thermostat is compatible with the...
Owner's Manual - Page 4
... power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Contact your old thermostat in the trash if it contains mercury in a sealed tube.
MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and ...
Owner's Manual - Page 5
... wires and remove the old wallplate only after all wires are attached to a terminal marked C or C1, they will not be connected to your new thermostat. If any wires are not attached to your old thermostat or are labeled.
RTH2310 Programmable Thermostat
Identify Wires
3.
Owner's Manual - Page 6
Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Insert plastic anchors.
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 Labels don't match? RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5. If a wire does not match any excess wire back into the wall opening.
Owner's Manual - Page 9
RTH2310 Programmable Thermostat
Specify Furnace Type
6. J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 Set the Jumper J2, on the back of the thermostat, if you have connected a wire to the G terminal. HE Place the jumper to this factory-set position if you have a gas or oil furnace.
Owner's Manual - Page 10
.... You will display the ambient temperature once it is 70 °F (21 °C).
9 Afterwards, the screen displays the actual temperature. Observe the
polarity. 3) Reinstall the battery cover. After the batteries are holding the thermostat. The thermostat will hear a clicking
sound. By default, the setpoint is installed on the wall.
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
How To Change Batteries In Honeywell Thermostat Manual Th3110d1008
(Posted by bubbsim 10 years ago)
How To Change Battery In Honeywell Thermostat Manual Rth2310b
(Posted by colojw 10 years ago)
How To Change A Battery In A 7 Day Programable Thermostat
(Posted by buddy2004 11 years ago)