Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by eladio62 on December 25th, 2013
Can't Get Heater System To Stay On (rth2310),
thermostat was preset by old owner, can't figure out how to reset it.
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
... for fast and easy installation. Just follow the simple step-by-step instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the wires. If the wire labels don't match. Specify the furnace type...
Owner's Manual - Page 3
... the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi-stage systems.
2 This thermostat is not compatible with or without pump • a millivolt system • a central heating and cooling system
If you are not sure of your system type...
Owner's Manual - Page 4
... your local waste management authority for instructions regarding recycling and proper disposal.
3 Do not remove wallplate yet. Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached. Contact your old thermostat in the trash if it contains mercury in a sealed tube.
Owner's Manual - Page 5
...RTH2310 Programmable Thermostat
Identify Wires
3. Do not use C or C1 wires
Identify and label each of each wire. Wrap the wires around a pencil to identify wires. IGNORE WIRE COLORS: Use terminal screw designations to prevent them from falling though the wall opening.
4 Disconnect wires and remove the old... will not be connected to your old thermostat or are labeled. Do not use...
Owner's Manual - Page 6
Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5 Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Insert plastic anchors.
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 If a wire does not match any excess wire back into the wall opening. Labels don't match...
Owner's Manual - Page 9
J2 jumper
HG Leave the jumper in this position if you have an electric furnace.
8 RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Set the Jumper J2, on the back of the thermostat, if you have connected a wire to this factory-set position if you have a gas or oil furnace. HE Place the jumper to the G terminal.
Owner's Manual - Page 10
... is normal that the displayed temperature be higher than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. The thermostat will hear a clicking
sound. By default, the setpoint is installed on the wall. Quick Installation Guide
Install Batteries
7.
1) Pull out the battery cover. 2) Install...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do I Go Clear The Setting On My Thermostat?
How do I set my Honeywell TH4210D1005 thermostat back to factory settings? Every time I go from heat...
How do I set my Honeywell TH4210D1005 thermostat back to factory settings? Every time I go from heat...
(Posted by mks901 2 years ago)
Change To Programmable Thermostat
can't hook up new programmable thermostat using the same wires as the old thermostat how do you conn...
can't hook up new programmable thermostat using the same wires as the old thermostat how do you conn...
(Posted by kikitwo 9 years ago)
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
How To Wire Rth2310 To An Oil Fired Boiler?
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
I have an oil fired boiler with three zones. I am trying to install RTH2310 Stats to control each zo...
(Posted by Grayai 12 years ago)