Honeywell RTH2310 Support Question
Honeywell RTH2310 Support Question
Find answers below for this question about Honeywell RTH2310.Need a Honeywell RTH2310 manual? We have 1 online manual for this item!
Question posted by cdtenglish on December 14th, 2011
Factory Defaults
I can not program the thermostat. Is it possible to set it back to factory defaults? If so, how?
Current Answers
Related Honeywell RTH2310 Manual Pages
Owner's Manual - Page 1
Quick Installation Guide
RTH2310
Programmable Thermostat 69-2214EF-02
Owner's Manual - Page 2
...instructions in the following pages.
Identify your system type. Remove your old thermostat. Identify the wires. Mount the new wallplate. Connect the ...batteries. Install the thermostat. Set the system.
Do you need assistance? Quick Installation Guide
Installation is Easy
Your new thermostat has been designed for fast and easy ...
Owner's Manual - Page 3
...
If you are not sure of your system type or if you have any other questions, call us toll-free at 1-800-468-1502.
This thermostat is compatible with the following systems:
• Gas, oil or electric furnace • Central air conditioner • a hot water system with heat pumps or multi...
Owner's Manual - Page 4
... wallplate yet. MERCURY NOTICE: Do not put your local waste management authority for instructions regarding recycling and proper disposal.
3
Quick Installation Guide
Remove Old Thermostat
2.
1) Turn power off at the heating/cooling system.
2) Remove old thermostat, but leave wallplate with wires attached.
Owner's Manual - Page 5
...cannot touch and short other wires. Wrap the wires around a pencil to your old thermostat or are labeled. Do not use non-connected wires.
Disconnect wires and remove the ...will not be connected to prevent them from falling though the wall opening.
4
RTH2310 Programmable Thermostat
Identify Wires
3.
IGNORE WIRE COLORS: Use terminal screw designations to identify wires. Wrap...
Owner's Manual - Page 6
Insert plastic anchors. Quick Installation Guide
Mount New Wallplate
4.
1) Remove coverplate.
2) Loosen screw (the screw remains captive on wallplate).
3) Remove thermostat.
4) Mark and drill appropriate mounting holes (or use existing holes). Pass wires through opening of wallplate and secure wallplate to the wall using provided screws.
5
Owner's Manual - Page 7
... with the terminal having the same letter.
2) Loosen the terminal screws using a screwdriver, insert the wires, then tighten the screws.
3) Push any terminal on the thermostat, see next page.
6 RTH2310 Programmable Thermostat
Connect Wires (typical wiring) 5.
Owner's Manual - Page 9
Set the Jumper J2, on the back of the thermostat, if you have an electric furnace.
8 J2 jumper
HG Leave the jumper in this factory-set position if you have connected a wire to this position if you have a gas or oil furnace.
HE Place the jumper to the G terminal.
RTH2310 Programmable Thermostat
Specify Furnace Type
6.
Owner's Manual - Page 10
... than the ambient temperature if you are installed, the thermostat performs a series of tests for approximately 5 seconds. After the batteries are holding the thermostat. It is installed on the wall. Afterwards, the screen displays the actual temperature. The thermostat will hear a clicking
sound. By default, the setpoint is 70 °F (21 °C).
9 Observe the...
Owner's Manual - Page 11
RTH2310 Programmable Thermostat
Install thermostat
8.
1) Mount the thermostat on the wallplate.
2) Tighten the screw and install the coverplate.
3) Turn power back on at the heating/cooling system.
10
Owner's Manual - Page 12
... per hour 3
2, 3, 4, 5 or 6 4
Cooling cycles per hour 3
2, 3, 4, 5 or 6 5
1 Default settings are shown in bold and underlined.
2 See page 3 of Operating Manual.
3 Use the system switch to switch between the two... parameters.
4 For optimal heating control, use the setting that matches your system as follows: 2=30 min (steam, gravity), 3=20 min (hot ...
Owner's Manual - Page 13
Guide d'installation rapide
RTH2310
Thermostat programmable 69-2214EF-02
Similar Questions
How Do You Reset A Honeywell Thermostat Model Number Rth2310
(Posted by mietsacre 9 years ago)
Hello, Our Honeywell Thermostat Display Settings Have Stopped Working. The Model
(Posted by mbuklerewicz 10 years ago)
Why Is Thermostat Temperature Set 5 Degrees Higher Than Required
(Posted by perhar71 11 years ago)