Honeywell CT41A Support Question
Honeywell CT41A Support Question
Find answers below for this question about Honeywell CT41A.Need a Honeywell CT41A manual? We have 1 online manual for this item!
Question posted by strachanlhizz on March 4th, 2015
Switch To Auto
I am not able to switch my thermostat to auto. The arm will not go down to the auto option.
Current Answers
Answer #1: Posted by TommyKervz on March 6th, 2015 3:55 PM
TommyKervz
Member since:
January 10th, 2013 Points: 17,776,813
Member since:
January 10th, 2013 Points: 17,776,813
Sound like the arm have stacked. Do consider seeing a repairman or take it back to the shop if still under warranty. You can Call/Email/Request a call for further assistance
Related Honeywell CT41A Manual Pages
Owner's Manual - Page 1
... BIT, IF NEEDED TO DRILL HOLES IN WALL
WIRE CUTTER/STRIPPER IF NEEDED TO STRIP WIRES
MERCURY SWITCH
TYPICAL LOCATION OF A MERCURY SWITCH IN A THERMOSTAT
M10614
LEVEL, IF NEEDED TO LEVEL THERMOSTAT FOR APPEARANCE
M20551
Fig. 1. YOUR NEW CT41A THERMOSTAT
If you place a check mark in the trash. If not, return it properly. Acquire the required...
Owner's Manual - Page 2
...thermostat...thermostat matching terminals.
2 Locating heat anticipator adjustment mechanism.
❑ Loosen screws holding thermostat...thermostat for future reference.
Connect wires from the old thermostat.
move on old thermostat... Thermostat
...thermostat...THERMOSTAT TO WALL OR OUTLET BOX)
ADJUSTABLE HEAT ANTICIPATOR SETTING LEVER
MOUNTING CLIPS (FOR COVER)
FAN SWITCH SYSTEM SWITCH...
Owner's Manual - Page 3
...hole. (Move the temperature setting lever, if necessary, to 0.4A.)
CT41A HEATING/COOLING THERMOSTAT
8406
SHOWS VOLTAGE RATING
SHOWS ANTICIPATOR SETTING
V8043E 1004 4 24V 50/60CY ...Fig. 7.
Set heat anticipator at recommended rating to prevent drafts from affecting thermostat operation.
❑ Remove thermostat cover by pulling outward on your primary control at the rating printed on the...
Owner's Manual - Page 4
....
❑ Turn on . Off: heating and air conditioning systems are disconnected. CT41A HEATING/COOLING THERMOSTAT
4 CHECK OUT THERMOSTAT
The System switch controls as follows: Auto: fan operates when heating or air conditioning system operates. Cool: air conditioning system only operates. The Fan switch controls as follows: Heat: heating system only operates. Move the temperature setting...
Owner's Manual - Page 5
...power to make sure it is turned off. Thermostat setting and thermometer reading disagree. Turn furnace power switch to thermostat. Repair frayed or broken wires. System switch is in temperature greater than 2°F (1&#...period is not level. Blown fuse or tripped circuit breaker. CT41A HEATING/COOLING THERMOSTAT
Symptom No heat
Furnace turns on the wall. No air conditioning.
Replace fuse ...
Owner's Manual - Page 6
...OF COVER
THERMOMETER SHAFT
M8068
HEX HEAD WRENCH
Fig. 8. Follow this procedure: ❑ Remove thermostat cover. ❑ Set the cover on a table near an accurate
thermometer. ❑ ... the system into the thermostat shaft and turn it until the thermometers have the same reading. CT41A HEATING/COOLING THERMOSTAT
7 RECALIBRATE THERMOMETER
If the thermostat setpoint and the thermometer ...
Owner's Manual - Page 7
....
This warranty shall not apply if it is defective, (i) return it (at Honeywell's option) within the terms stated above. If the product is shown by Honeywell that the defect or... and service, for a period of one (1) year from state to be to you. CT41A HEATING/COOLING THERMOSTAT
Limited One-Year Warranty
Honeywell warrants this product, excluding battery, to state. If you may...
Owner's Manual - Page 8
Rev. 10-03
Printed in U.S.A. Honeywell Limited-Honeywell Limitée
1985 Douglas Drive North
35 Dynamic Drive
Golden Valley, MN 55422
Scarborough, Ontario
M1V 4Z9
69-0788-2 G.H.
www.honeywell.com/yourhome on recycled paper containing at least 10% post-consumer paper fibers. CT41A HEATING/COOLING THERMOSTAT
Automation and Control Solutions
Honeywell International Inc.
Similar Questions
I Can't Set Our Th6320r Thermostat In Auto Changeover Mode
as noted we have geothermal pumps controlled by th6320r thermostats. They won't enter auto changeove...
as noted we have geothermal pumps controlled by th6320r thermostats. They won't enter auto changeove...
(Posted by nstasseljunk 6 years ago)
Set Cycle Rate Switch On Ct87k Thermostat
My "SET CYCLE RATE SWITCH", both switch 1 and switch 2 are set to off. I question the supplied table...
My "SET CYCLE RATE SWITCH", both switch 1 and switch 2 are set to off. I question the supplied table...
(Posted by ptomtan 7 years ago)
Does The Thermostat Automatically Switch To Electric Heat When It Gets Cold
When to use EMHEAT and Auto setting in heat cycle.
When to use EMHEAT and Auto setting in heat cycle.
(Posted by gator74 9 years ago)
Blower Blowing Despite One Switch Is Turned To Auto And Heat/cool Switch Is Off
Why does air continue to be blow even with the system switch turned off? Is it because the batteries...
Why does air continue to be blow even with the system switch turned off? Is it because the batteries...
(Posted by beachkitty52 9 years ago)
Can Hear Switch Click For Heat, But Heat Not Started. Second Thermostat Works.
Can hear switch flip on inside thermostat, but longer and longer delay for heat to start (10 min to ...
Can hear switch flip on inside thermostat, but longer and longer delay for heat to start (10 min to ...
(Posted by Truesrv 10 years ago)