Honeywell CT3200 Support Question
Honeywell CT3200 Support Question
Find answers below for this question about Honeywell CT3200.Need a Honeywell CT3200 manual? We have 1 online manual for this item!
Question posted by cespama on October 21st, 2020
Thermostat Ct3200a1019 Replacement
What's a good replacement for Honeywell thermostat Ct3200a1019?
Current Answers
Answer #1: Posted by INIMITABLE on October 22nd, 2020 2:35 AM
INIMITABLE
Member since:
April 3rd, 2020 Points: 2,082,030
Member since:
April 3rd, 2020 Points: 2,082,030
Are you reading the voltage with a meter. The unit you are trying to replace is 24 vac transformer to the timer. Any 24 vac thermostat should work.
Voltage trouble shooting chart:
Voltage at Timer Terminals
Ac Voltage at
C-R Terminals Possible Cause Check Action
0 Vac 1. System power is Off. 1. Restore power.
2. Short in timer power supply wiring. 2. Replace wiring.
3. Limit switch contacts stuck open. 3. Free or replace limit switch.
4. Transformer supplying power is
burned out.
4. Replace transformer.
Up to 15 Vac. 1. System transformer used to power
the timer is inadequate.
1. Use additional (separate)
transformer.
2. Additional (separate) transformer
used to power the timer has
inadequate voltage.
2. Install transformer with proper
secondary voltage.
15 to 30 Vac. 1. Spring fingers on thermostat not
making proper contact with
subbase terminals.
1. Rebend spring fingers to a
45 degree angle to ensure
proper contact.
2. Timer has failed. 2. Replace thermostat.
Hope this helps!
I hope this is helpful? PLEASE "ACCEPT" and mark it "HELPFUL" to complement my little effort. Hope to bring you more detailed answers
-INIMITABLE
Related Honeywell CT3200 Manual Pages
Owner's Manual - Page 1
... Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model CT3200
Welcome to the world of Contents
Installation
2
Programming
11
Operation
17
Change the clock for Daylight/
17
Standard Time
Set the Fan and System switches 17
Replace the batteries
18
Override the program settings
19
Frequently asked...
Owner's Manual - Page 2
...-0653-6
Multistage Conventional A heating or cooling system with CT3200? Fig. 1
MERCURY SWITCH
Recycling Thermostat
If you are removing an old thermostat that include warm air furnaces and hot water. Heating/... thermostat is the right thermostat for your system is not compatible with radiator heat.
If your system, visit us on the Web at www.honeywell.com/yourhome or call Honeywell...
Owner's Manual - Page 3
...°C).
69-0653-6
INSTALLATION 3 Honeywell recommends Energizer® • Wire cutter/stripper or sharp knife
batteries.
• Level
• Screwdriver
• Electrical tape
• Hand or power drill with either system, call a heating/air conditioning contractor-the problem may persist after you have the following parts:
• Thermostat and mounting plate •...
Owner's Manual - Page 4
... are extra wires that it . If the wiring meets any of the terminal that are not connected to the old thermostat. Do not label the wires by color. Remove the old thermostat
Fig. 2
Fig. 3
M20140
Fig. 4
M19086
WIRES THROUGH WALL OPENING
4 INSTALLATION
M20133
a. f. e.
Using the enclosed labels, mark the wires with wires...
Owner's Manual - Page 5
... progress The mounting plate is now mounted on the wall. d.
Install the mounting plate
Fig. 5
M20139
Fig. 6
M20129
Fig. 7
a.
Separate the mounting plate from the thermostat using a coin, as shown in drywall, gently tap the anchors that were provided into each of the mounting plate's screw holes. Be sure the mounting...
Owner's Manual - Page 6
... maintain accurate temperature control, minimize swings in degrees Celsius (°C), adjust screw C out one turn. If you can wait until the thermostat is set your new thermostat for the type of heating system. To install the batteries, see the instructions that your type of the room, and efficiently run the fan. Use...
Owner's Manual - Page 7
... on the wires, match the letter of the old wires to connect all of your new thermostat.
Heating System Table Note: Setting the screw "out one turn" means turning the screw 360..., or oil heating system with the corresponding terminal on the new thermostat terminals, you might not need to the new thermostat. See the special wiring instructions on the furnace.)
High-efficiency furnace...
Owner's Manual - Page 8
... the batteries. M20130
Step 7. Go to flash a default time and the current temperature (Fig. 14).
Honeywell recommends using Energizer® batteries. Replace the battery door. c. e. Align the tabs at the top of the thermostat with the tabs at the top of the mounting plate (Fig. 11). b. b. You are oriented correctly as shown in...
Owner's Manual - Page 9
...NOT work with such systems and should be insulated from each other to avoid damaging your old thermostat has six or more wires (excluding clock wires attached to the place of purchase. You will... allow these wires to touch.
Wrap the wires separately, using the fan ON switch, the 3200 thermostat will not interfere with electrical tape and place them . Tape off . Six or more wires If...
Owner's Manual - Page 10
... cooling (Y2). You have a single stage heat pump or zoning system. Remove the jumper before wiring the R and Rc terminals.
See page 2 for an alternate thermostat model.
*Remove factory-installed jumper between the R and Rc terminals (Fig. 15). Transformer common.
See page 2 for cooling Heat
Cooling
Fan Changeover in cool (O terminal...
Owner's Manual - Page 11
...1 Fan switch-Selects automatic fan operation or fan on
(page 17)
9
2 Set Schedule-Puts the thermostat into programming
10
mode (page 14)
11
3 Set Clock/Day-Sets the clock and day (page ...11 Temp Warmer and Cooler-Sets the temperature warmer and cooler (page 14)
12 Run Program-Returns thermostat to normal operating mode
13 Hold Temp-Holds a selected temperature (page 19) 14 System switch-Selects...
Owner's Manual - Page 12
... and the current temperature are defined on the next page.
12 PROGRAMMING
69-0653-6
Press
once. c.
Press
once. Learn about the programming features
Your 3200 thermostat allows you will want to program schedules for the weekends (Saturday and Sunday). The day is displayed (Fig. 17).
Press and hold
or
until the...
Owner's Manual - Page 13
...
The time when you get up an energy-saving temperature for this period.
The time when you are regularly away from home. Use of your thermostat, it will remain in effect until you are sleeping.
Owner's Manual - Page 16
... before turning on the air conditioner. Step 5. c.
Your cooling system and fan should run after a short delay. Note: When the cooling setting is changed, the thermostat may delay up to COOL. c. Your heating system should start and the fan should start.
e. Check out the system Verify that your heating system works...
Owner's Manual - Page 17
... to AUTO.
f. Set the System switch to OFF and the Fan switch to the G terminal on the bottom of the thermostat faceplate (Fig. 16 page 11) control the operation of the thermostat.
69-0653-6
OPERATION 17
The current time and day and the current temperature are displayed. A two-speed fan usually runs...
Owner's Manual - Page 18
..., wait for longer than a month, change the batteries before leaving to prevent the system from shutting down due to reprogram the thermostat.
Note: If "bAt Lo" continues to display after replacing the batteries, set the System switch to remove them. If you are oriented correctly as possible, within 20-30 seconds of...
Owner's Manual - Page 21
...continues to display after replacing the batteries, set to HEAT. • Check the system fuse or circuit breaker and replace or reset if necessary. • Check for correct wiring and good connections. • If...is higher than the current room temperature and
the SYSTEM ON arrow is displayed, the thermostat is 45°F-88°F (7°C-31°C).
• The batteries are fresh and installed...
Owner's Manual - Page 22
...the system fuse or circuit breaker and replace or reset if necessary. Adjust the screws on the back of wires connected to the thermostat
NOTICE: This equipment is set to ... room temperatures may differ for assistance.
Check for correct wiring and good connections.
If display is operating correctly. The thermostat has a built-in the wall behind the mounting plate with Canadian...
Owner's Manual - Page 23
... IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE ONE YEAR DURATION OF THIS WARRANTY.
Limited warranty
Honeywell warrants this product, excluding battery, to be to repair or replace the product within a reasonable period of purchase by damage which vary from state to state.
Owner's Manual - Page 24
Home and Building Control Honeywell 1985 Douglas Drive North Golden Valley, MN 55422
69-0653-6 Rev. 9-01
Home and Building Control Honeywell Limited-Honeywell Limitée 35 Dynamic Drive Scarborough, Ontario M1V 4Z9
Printed in the U.S.A.
www.honeywell.com/yourhome
Similar Questions
Digital Thermostat To Replace A Trolatemp T8090t 2-zone For Cooling And Heating
I need digital thermostats to replace two (mercury) thermostats connected to one Central AC and one ...
I need digital thermostats to replace two (mercury) thermostats connected to one Central AC and one ...
(Posted by tariqazizsiddiqui 8 years ago)
Honeywell Thermostat Ct3200- Cooling Does Not Come On
(Posted by sdceasyg 9 years ago)
