Honeywell CT3200 Support Question
Honeywell CT3200 Support Question
Find answers below for this question about Honeywell CT3200.Need a Honeywell CT3200 manual? We have 1 online manual for this item!
Question posted by sarahkc535 on September 7th, 2014
Honeywell Magicstat Thermostat Can See Display
The person who posted this question about this Honeywell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Honeywell CT3200 Manual Pages
Owner's Manual - Page 1
...MagicStat® CT3200 Programmable Thermostat
Installation and Programming Instructions
Weekday/Weekend (5-day/2-day) Programmable Heat and/or Cool Low Voltage (20 to 30 Vac) Thermostat and Mounting Plate Model CT3200... new thermostat will automatically control the temperature in your new Honeywell MagicStat® Programmable Thermostat. Registered Trademark Copyright © 2001 Honeywell •...
Owner's Manual - Page 2
...
69-0653-6 Steam A steam boiler with the CT3200, the table recommends an alternate Honeywell model.
Contact your system, visit us on the Web at www.honeywell.com/yourhome or call Honeywell Customer Relations at 1-800-468-1502.
Heat Pump Heating and cooling are removing an old thermostat that include warm air furnaces and hot water...
Owner's Manual - Page 3
...-inch drill bit
• Pencil
c. Carefully unpack your heating and cooling systems are working properly. Make sure that your new thermostat.
Required tools and supplies
Optional tools
• Two AA alkaline batteries. Honeywell recommends Energizer® • Wire cutter/stripper or sharp knife
batteries.
• Level
• Screwdriver
• Electrical tape
•...
Owner's Manual - Page 4
... it . Step 2. b. c. If the wiring meets any of the following conditions, see the wiring cross reference table on page 9. • The old thermostat is attached to the old thermostat.
If the labels do not disconnect the wires.
Using the enclosed labels, mark the wires with wires attached to the C or C1 terminals...
Owner's Manual - Page 5
Separate the mounting plate from the thermostat using a coin, as shown in drywall, gently tap the anchors that were provided into each of the drilled holes or anchors (Fig. 6). If installing in ...
Owner's Manual - Page 6
Note: This setting enables proper fan operation. Note: These screws are factory-set for the type of fuel that begin on the back of the thermostat to display the temperature in degrees Fahrenheit (°F).
b. If you can install the batteries and program your type of heating system. To install the batteries, see the...
Owner's Manual - Page 7
...the screw 360° counter-clockwise, or one turn .
Note: If the letters on the old thermostat terminals do not match the letters on the back of system Warm air, gas, or oil heating... system with the corresponding terminal on the new thermostat terminals, you might not need to connect all of the old wires to the new thermostat.
Securely tighten the terminals.
69-0653-6
END OF ...
Owner's Manual - Page 8
...of the case to program the thermostat. Press the lower edge of the thermostat (Fig. 12). b. d. b. Honeywell recommends using Energizer® batteries....thermostat
Fig. 11
Fig. 12
a. Remove the clear plastic label from the digital display. Check your progress When the batteries are installed correctly, the digital display flashes all entries once, then begins to program the thermostat...
Owner's Manual - Page 9
... multistage system.
Continue the installation procedure on page 2 for information about which programmable thermostat WILL work with your electrical circuit. Continue with the installation as instructed on page ...to insulate the wires. Tape off . Special wiring instructions
A clock thermostat with C or C1 terminals A clock thermostat has one or two extra wires attached to the C or C1 ...
Owner's Manual - Page 10
... terminal) or changeover in 5-wire systems.
10 INSTALLATION
69-0653-6
Old thermostat terminal
Connect to wire the new thermostat. REMOVE IF 5-WIRE SYSTEM
R
Rc
WY G
M20127
Old thermostat terminals that do not match new thermostat terminals Use the table below to new thermostat terminal
Description
R, RH, 4, V Rc, R W, W1, H Y, Y1, M G, F O B
C, X, B W2, H2 Y2
R* Rc* W Y G Do...
Owner's Manual - Page 11
...1 Fan switch-Selects automatic fan operation or fan on
(page 17)
9
2 Set Schedule-Puts the thermostat into programming
10
mode (page 14)
11
3 Set Clock/Day-Sets the clock and day (page 12...TEMPORARY-An arrow displays when a temporary override is made to the program (page 19)
11 Temp Warmer and Cooler-Sets the temperature warmer and cooler (page 14)
12 Run Program-Returns thermostat to normal ...
Owner's Manual - Page 12
...saving temperature higher.
The time is displayed (Fig. 18).
Fig. 18
d. Step 1.
Fig. 19
Step 2. Press
once. Learn about the programming features
Your 3200 thermostat allows you to two program periods ... higher and the energy-saving temperature lower. • The reverse is
displayed. The current time and day and the current temperature are defined on the next page.
...
Owner's Manual - Page 13
... that is programmed for this period.
Program period
WAKE
LEAVE RETURN
SLEEP
Description
The time when you get up and get ready to leave your thermostat, it will remain in effect until you are sleeping. You can set the system at a comfortable temperature for this period. The time when you reach...
Owner's Manual - Page 14
...;F (21°C)
LEAVE
8:00 AM 62°F (16.5°C)
RETURN
6:00 PM 70°F (21°C)
b.
Set the Monday-Friday WAKE time by pressing
or displayed. for your heating schedule.
Step 3. Write in the times and temperatures that you want to program for
each weekday program period. Set the Monday-Friday...
Owner's Manual - Page 15
.... 23).
k.
Set the Saturday and Sunday WAKE temperature by pressing
or
until the desired time is displayed (Fig. 24). through j. Press
to set
the program. Write in the times and temperatures that you want to display a blank schedule for your cooling schedule. Cooling Schedule
Suggested Settings
Weekday (Mon-Fri)
Weekend (Sat-Sun...
Owner's Manual - Page 16
... setting is 10°F (6°C) below room
temperature (Fig. 26). Your heating system should run after a short delay.
Press
until the setting is changed, the thermostat may delay up to COOL. Note: When the cooling setting is 10°F (6°C) below room
temperature. b. Set the System switch to 5 minutes before turning...
Owner's Manual - Page 17
...thermostat.
69-0653-6
OPERATION 17
Operation Change the clock for more efficient air cleaning.
Auto is 10°F (6°C) above room
temperature. Press
until the correct time is displayed.
The time is displayed...c. Press
once.
The current time and day and the current temperature are displayed. Switch Fan
Setting Result
Auto On
A single-speed fan turns on low...
Owner's Manual - Page 18
... lack of removing the old ones, you see page 12 to their correct orientation.
Dead
Replace the batteries immediately. However, if the display is not operating. Heat The thermostat controls your air conditioning system. Your heating/cooling system is blank, the batteries are dead or incorrectly installed and you are leaving home...
Owner's Manual - Page 21
... insert them as soon as possible. Frequently asked questions
If... Replace the batteries correctly. Display will not go lower than 45°F (7°C) or higher than the current room temperature and
the SYSTEM ON arrow is displayed, the thermostat is 45°F-88°F (7°C-31°C).
• The batteries are fresh and...
Owner's Manual - Page 22
... the current room temperature and the SYSTEM ON arrow is displayed, the thermostat is blank or says "bAt Lo," install fresh batteries...thermostat, please read and follow the instructions. If...
Press
to check the current temperature setting. Adjust the screws on the back of wires connected to 30 minutes after changing the setting before the air conditioner starts. If you call Honeywell...
Similar Questions
Where Is Reset Button Honeywell Thermostat Ct3200 Manual
(Posted by Camce 9 years ago)
Honeywell Thermostat Ct3200- Cooling Does Not Come On
(Posted by sdceasyg 9 years ago)
How To Install Magicstat Thermostat Honeywell Ct3200
(Posted by khuntjcast 9 years ago)
Diagram How To Wire Honeywell Ct3200 Magicstat Thermostat
(Posted by roy196ngar 9 years ago)
