Honeywell 4286 Support Question
Honeywell 4286 Support Question
Find answers below for this question about Honeywell 4286 - Ademco Phone Module.Need a Honeywell 4286 manual? We have 1 online manual for this item!
Question posted by johmals on April 4th, 2014
Model Xl 4600sm Keypad
mymobileis not aboutif there isalarmabout. Canyou help methere? What canI doto get it backon? He did itbeforethough. What Iwant totellis that mytelefhonelinealsoatgood work. There isconnection.
Current Answers
Related Honeywell 4286 Manual Pages
User Guide - Page 3
... ...2 Summary...2
Operating Overview From An On-Premises Phone 3 Accessing The Security System Using An On-Premises Phone 4 Operating Overview From An Off-Premises Phone 5 Accessing The Security System Using an Off-Premises Phone 6
Telephone Systems Equipped with Answering Machines 7 Executing System Commands Via The Phone 8 Telephone Keypad Command Functions 9
System Commands That May be...
User Guide - Page 5
Introduction
General Information
ADEMCO's VIP (VISTA Interactive Phone) Module permits you to control your security system via a Touch-tone phone (either on and off -premises phone that phone will not be possible. Voice comments or confirmation tones are provided over the phone as confirmation after dialing; in when away).
With this feature. Type of a number from that does not...
User Guide - Page 6
... the wired keypad. Successful access to -follow describe how to access your security system via a Touch-tone phone, either on or off -premises phone) are followed by step-by the phone module. After accessing the security system via the phone.
when accessing the system from an off the premises, and describe how to the system, and other helpful information...
User Guide - Page 7
Pick up any
phone on the phone.
* In some systems, a voice prompt for entry of the 4digit System code will not occur.
TYPICAL TELEPHONE KEYPAD WITH EQUIVALENT COMMAND FUNCTIONS
OFF
1
MAX
GHI
4 INST...After entry of an appropriate voice
announcement and "beeps" on premises
Dial Tone
Enter 2-digit Phone Code
If the System is in , or immediately following , the Status Report.
To ...
User Guide - Page 8
... the word "HELLO", and followed automatically by -Step Procedure
To access the security system from on-premises, proceed as arm, disarm, etc.) using the keypad on the phone. Enter the System Command.
this time - Accessing the Security System Using an On-Premises Phone
Step-by a description of the status of the status report begins on...
User Guide - Page 9
...
outgoing message. TYPICAL TELEPHONE KEYPAD WITH EQUIVALENT COMMAND FUNCTIONS
*On the same line.
When you have accessed the system, all phones on the phone.
5 Confirmation of successful execution...following , the Status Report.
Operating Overview from an Off-Premises Phone
Dial premises
phone number
If security system responds directly
(even if in Alarm)
If an answering machine responds
2 long ...
User Guide - Page 11
..., as arm, disarm, etc.) using the keypad on the phone. Telephone Systems Equipped with Answering Machines
The 2-digit phone code should be received by entry of the security system. See Executing System Commands Via the Phone that touch tones (produced
by the security system while an answering machine's outgoing phone message is that follows on page 15...
User Guide - Page 12
... ANY KEYS DURING SYNTHESIZED VOICE REPORTING. Following your 4digit system code followed by the Phone Module, it impossible to arm the system unless that follows shows a typical telephone keypad with command functions, but telephone keypads are faulted (which will cause the phone system to its command function.
8 The diagram that zone is "Disarmed, Not Ready...
User Guide - Page 13
Telephone Keypad Command Functions
OFF
1
MAX
GHI
4 INST
PRS
7 READY
D
AWAY
ABC
2
STAY
DEF
3
TEST †
JKL
5
BYPASS
MNO
6
CODE... ONLY * IF PROGRAMMED
System Commands That May Be Executed Via the Phone
The following are typical system commands that may be executed via the Touch-tone phone once you have obtained access to the security system: • ARM STAY, AWAY, INSTANT, or MAXIMUM •...
User Guide - Page 14
... all open zones
To enable SPEAKER OUTPUT
Yes No
To trigger PANIC alarm
Entry To Be Keyed On Phone System Security code + key [3]. Master Security Code + key [8] + User No. + Temporary Code. System Security code + key [2]. System Security Code + key [6] + zone # to your system can perform this function.
10 your installer should have indicated whether your...
User Guide - Page 15
... where the Phone module's vocabulary does not permit annunciation (e.g., TEST, etc.), the system will be confirmed by the same number of "beeps" as appropriate) after successful command entries.
For those produced by phone confirmation of successful entry of that will be heard after a successful entry, and annunciate the words "SEE SYSTEM KEYPAD." The following...
User Guide - Page 16
... AWAY, the caller enters the 4-digit system security
code, then presses key 2 (AWAY) .
7.
Do NOT make sure that the system was not armed.
6. EXIT NOW."
8. No answering machine is speaking.
* The command can also be done during a 1-second pause placed by the Phone Module between each phone message.
After a programmed number of rings, the...
User Guide - Page 17
... keypad while keeping the person on hold.
• If the System is possible to listen for example, the system is armed, you can be continued after the DISARM command has been keyed. There will be no dial tone will be present when the on-premises phone is picked up by entering your security...
User Guide - Page 19
... (only when Off). • Chime sounds (if chime mode is on the installer designated security keypad(s). Note: Alarm warning sounds may be annunciated with your system, press G
key to the system...sound), or Burglary sound (2-tone siren sound). A system command may not be provided over the phone with a leading zero). * If programmed by your installer.
15
If not annunciated in some...
User Guide - Page 22
The VIP Module will produce "beeps" (if appropriate) over the phone similar to those from the wired keypad. System Status Reports Not Annunciated
Certain system status messages are displayed on a keypad only, such as: • Transmitter Low Battery • Test Mode • Call Alarm Company • Comm Failure. These messages will annunciate "SEE SYSTEM KEYPAD" under...
User Guide - Page 23
... minutes prior to 5 minutes or a sequence of the alarm to the alarm monitoring station. Phone access will be terminated immediately if an alarm dialer report is triggered in the system. A ... A remote access session (call-in) will also be terminated if the valid phone and system security codes had not already been entered when other types of dialer reports are limited to calling for 20...
User Guide - Page 26
...phone feedback when a relay command is , place a check in your 4-digit system security code + [#] + 70. To activate devices via the phone. Voice Prompt: "(Voice Descriptor), DEVICE ## ON/OFF. If your 2digit phone...mode is the relay phone descriptor programmed by the... access the security system using your... depression, the phone module will be programmed... The following phone prompts will ...
User Guide - Page 29
...or hang up before continuing.
2. If "1" is pressed twice on the monitored keypad. Enables all possible speaker output including those sounds listed below . User command ... all sound categories. It will not mute certain panel synthesized phone commands that the control directs to end before the Phone Module announces "Exiting", then any changes made will be lost.
If...
User Guide - Page 31
... an Entry Delay period, or when the phone is communicating with the Phone module - If the phone is a switchable type (has a TONE-PULSE switch), make sure the phone is out of 2-digit phone code may have been entered incorrectly. This indicates a problem with your 2digit Phone Code to access the security system. Always allow at least 12 seconds...
User Guide - Page 33
...security system.
29 THIS WILL CAUSE COMPLETE DISRUPTION OF REGULAR TELEPHONE SERVICE.
If the regular phone service works correctly after the plug has been disconnected from the RJ31X wall jack, the security...OR AT THE PHONE MODULE - If You Have Trouble with Your Regular Telephone Service
In the event of trouble with your regular telephone service, disconnect the security system from the ...
Similar Questions
The Combination Gotten Thrown Away. I Have The Key.
(Posted by Fencemaster01 2 years ago)
Does A Honeywell 6270 Ademco Alarm System Have Any Batteries Located Anywhere?
I am trying to help a recently widowed member of the family out. She has a 6270 alarm system but kno...
I am trying to help a recently widowed member of the family out. She has a 6270 alarm system but kno...
(Posted by mmanning4394 2 years ago)
Ademco 6270 Touch Center User Can Only Alarm Partions Access Help
(Posted by jgalts 10 years ago)
Can I Arm Home Security Without Monitoring Vista 15p
(Posted by Civicjo 10 years ago)
Phone Module 4286
Hello, The module it's conecting from on premise and acepting all comands. Off premise it's acepting...
Hello, The module it's conecting from on premise and acepting all comands. Off premise it's acepting...
(Posted by wisesecurity 11 years ago)