Hitachi NT65GA Support Question
Hitachi NT65GA Support Question
Find answers below for this question about Hitachi NT65GA - 2-1/2" Gas Powered 34 Angled Finish Nailer.Need a Hitachi NT65GA manual? We have 2 online manuals for this item!
Question posted by Daveschwartzen on March 9th, 2017
Not Shooting
Put in a brand new genuine gas cartridge after using a generic cartridge. Now sounds like I'm not getting a full charge of gas and will not activate. Sounds like a tiny pop as apoased to a sho
Current Answers
Related Hitachi NT65GA Manual Pages
Instruction Manual - Page 5
... gasoline. English
SAFETY
IMPORTANT SAFETY INSTRUCTIONS FOR USING NAILERS
READ ALL INSTRUCTIONS
This Nailer is powered by the Nailer operator and others in work area.
2. NEVER USE IN PRESENCE OF FLAMMABLE LIQUIDS OR GASES. DO NOT TOUCH AROUND THE EXHAUST OUTLET.
Do not touch with dispensers for combustible gas which are listed in work area wear safety...
Instruction Manual - Page 6
... and battery away from
sunshine and from ignition sources - The device may burst, releasing flammable gas.
WARNING
5. The fuel cell is between 32°F (0°C) and 104°F
(40°C) so ensure use . Never point the Nailer at yourself toward yourself or others, whether it can lead to follow instructions may result in...
Instruction Manual - Page 7
... fasteners on the opposite side.
7
Check their condition periodically. Never use , the
120°F MAX (50°C)
Nailer, fuel cell and battery should be driven through the wall and hit a person on top of an angle; The fasteners can be store in tool case and
in low temperatures and drive operations may be driven...
Instruction Manual - Page 9
...not inhale its contents.
Fluid gases might cause injuries when getting in a vehicle).
(50 °C)
Do not expose to an open... Store in fire and explosion when handling dispensers for combustible gas for the purpose of fuel cell with other scrap for ... out of contact with skin or eyes. In case of the tool and disposal.
Do not refill, reclaim or recycle the fuel cell...
Instruction Manual - Page 11
...power cord from direct sunlight and use the Nailer. To avoid these instructions to avoid the risk of injury:
WARNING
ⅷ Improper use an engine generator or DC power to avoid overheating the charger.
14. NEVER
3. charge... not in places where the temperature may get wrapped around the driver's feet and cause an accident.
3. NEVER use of the battery or battery charger can ...
Instruction Manual - Page 13
... is designed to assist you in this Manual may show details or attachments that differ from those on your own Nailer. Some illustrations in the safe operation of the Nailer. NAME OF PARTS
1.
Gas Finish Nailer
Top cover
Actuator
Chamber
Handle
Top cover
Chamber
Actuator Handle Battery
Piston
Driver blade
Trigger
Battery Hook
Piston
Driver...
Instruction Manual - Page 14
... hole
Connecting socket
Charger connecting plug
Pilot lamp
Nameplate (on the bottom side)
Charger connecting plug
Cigarette lighter connecting plug
Cord
14
AC adapter
Cord Gas Brad Nailer
Top cover
Chamber
Piston Driver blade
Actuator Handle
Battery
Trigger
Hook Stop lever
Firing head
(outlet)
Push lever
Magazine
Magazine cover
3.
Instruction Manual - Page 15
...Charging voltage DC 3.6 V Charging current DC 1.5 A 0.4 lbs (0.2 kg)
NOTE: The charging time may vary according to temperature and power source voltage.
15 Gas Brad Nailer...-981......sold separately
3. Gas Finish Nailer
Model Dimensions
Length × Height × Width Weight Includes battery and fuel cell Nail capacity
Cycle rate
Battery Fuel Cell
NT65GS
NT65GB
NT65GA
10-1/4" × 11...
Instruction Manual - Page 16
... genuine HITACHI nails for the NT65GS, NT65GB, NT65GA or the NT50GS. English
NAIL SELECTION
WARNING
ⅷ Be sure to serious injuries.
Dimensions of any other nails can result in the Table below can be driven with this Nailer. Only nails shown in tool malfunction and/or nail breakdown, leading to use of nails
16 Gauge finish...
Instruction Manual - Page 18
... wrench for areas
around the doors, windows as well as finishing process for M5 screw 1 8 Nose cap (mounted on tool)
(except NT50GS 1 9 Nose cap (mounted on tool)
(only NT50GS 1 0 Case 1
CHARGING METHOD
NOTE: Before plugging into the receptacle, make sure the following points. ⅜ The power source voltage is stated on the nameplate. ⅜ The...
Instruction Manual - Page 19
... and prevent it repaired immediately. NOTE: The battery charging time becomes longer when a temperature is low or the voltage of the power source is loose and falls out of the cigarette lighter socket, repair the socket.
4. When the pilot lamp does not go out.
When using the cigarette lighter connecting
plug
⅜ Secure...
Instruction Manual - Page 20
... of the tool becomes weaker, stop using the tool and recharge its internal chemical substance will deteriorate, and the battery life will be low when using them the first and second time. Do not leave the battery charger or battery in case of new batteries and batteries that the battery or charger is not activated, the...
Instruction Manual - Page 21
...new metering valve. ⅷ Do not attempt to reuse the metering valve.
To attach the metering valve to warm up before use at worksite.
ⅷ Use outside or
well-ventilated
areas. CAUTION ⅷ This Nailer... Nailer,
120°F MAX fuel cell and
(50°C)
battery away from sunshine and
from temperature
exceeding 120°F
(50°C).
ⅷ Keep away from the gas cartridge....
Instruction Manual - Page 22
....1 specifications. Conduct the tests in page 18 - 20. If gas is not dispersed, fuel cell is now ready to throw the push
lever tip onto wood. The fuel cell is empty. The charging method of the metering valve.
If abnormal operation occurs, stop using the Nailer and contact a Hitachi authorized service center immediately.
(1) REMOVE...
Instruction Manual - Page 23
Charge the battery.
3 Insert the stem of fuel cell into nailer.
Push up and pull out the actuator.
2.
Pull out
NOTE: Insert a loose adapter according to the instructions in the figure. Fuel cell
Handle
Battery
Battery
release button
BATTERY INDICATOR LIGHT
Flashing GREEN: Enough
power
remaining (The light
turns steady during operation). OFF: The...
Instruction Manual - Page 27
...resulting in use the electrical cord if damaged. To ensure that gets on the opposite side.
ⅷ Never use Nailer which is defective or operating abnormally.
ⅷ Do not use Nailer as required...tool. NT65GS, NT65GA, NT65GB employ a preventive mechanism for an extended period may lead to drive a nail. CAUTION ⅷ Use caution not to be pushed up . It is equipped with Nailer...
Instruction Manual - Page 31
...use ,
(50°C)
the Nailer, fuel
cell and battery
should be driven at
temperature
below 120°F
(50°C).
31 Remove dust and
wooden chips which may show details or attachments that the nail feeder slides smoothly by pulling it with Hitachi Gas tool...gases.
ⅷ Keep away from Nailer when: 1) doing maintenance and ...on your own Nailer. English
MAINTENANCE
NOTE: The...
Instruction Manual - Page 32
... repair or other maintenance.
English
⅜ When not in use for an extended period, apply a thin coat of children. A new WARNING LABEL is extremely dangerous.
2. Regularly inspect them in ...notice. Do not use , the Nailer, fuel cell and battery should be helpful if presented with soapy water. Fuse replacement of HITACHI.
32 MODIFICATIONS: Hitachi Power Tools are subject to...
Instruction Manual - Page 34
... 120°F (50°C). Clean as instructed on the maintenance sheet.
Unable to charge battery.
----------
If green: Contact Hitachi for replacement. Check spark plug wire, worn ...the electrical cord.
34
Magazine empty. Contact Hitachi for replacement. Check filter, clogged?
If red: charge the battery.
indicator shows GREEN
yet it with a new fuel cell. CORRECTION ...
Instruction Manual - Page 112
... 1-800-59-TOOLS (llamada gratis), o con HITACHI AUTHORIZED POWER TOOL SERVICE CENTER. Shinagawa Intercity Tower A, 15-1, Konan 2-chome, Minato-ku, Tokyo 108-6020, Japan
Distributed by
Hitachi Koki Co., Ltd. au 1-800-59-TOOLS (appel gratuit), ou UN SERVICE APRÈS-VENTE D'OUTILS ÉLECTRIQUE AGRÉÉ PAR HITACHI.
Norcross, GA 30093
Hitachi Koki...
Similar Questions
Shoot One Nail Piston Shaft Will Not Go Back Up
(Posted by banubasdeo2 2 years ago)
Trouble Shooting
I'm wondering if anyone can give me help with my gun. It won't press down all the way anymore to alo...
I'm wondering if anyone can give me help with my gun. It won't press down all the way anymore to alo...
(Posted by Jordanmcmahon007 2 years ago)
Nt65ga Will Not Fire
NT65GA Does not fire when trigger is pulled. Battery has full charge.
NT65GA Does not fire when trigger is pulled. Battery has full charge.
(Posted by dmcgeeoo6 7 years ago)
I Can Adjust The Mitre Angle All The Way On The Right But It Stops At 10 Degrees
I can adjust the mitre angle all the way on the right but it won't budge past 10 degrees when I try ...
I can adjust the mitre angle all the way on the right but it won't budge past 10 degrees when I try ...
(Posted by rivuletcottage 9 years ago)
Turntable Wont Turn At All Stuck At Zero, Brand New Saw Never Been Used!
Turntable is locked at 45 degree angle. It is brand new
Turntable is locked at 45 degree angle. It is brand new
(Posted by brucescheer 13 years ago)