Hitachi NR83A2 Support Question
Hitachi NR83A2 Support Question
Find answers below for this question about Hitachi NR83A2 - 3.25" Full Head Framing Strip Nailer.Need a Hitachi NR83A2 manual? We have 2 online manuals for this item!
Question posted by ashrafkhan94069 on October 13th, 2019
Blinking Of Red Led
My ac was not working and started blinking led. For 7 times
Current Answers
Related Hitachi NR83A2 Manual Pages
Instruction Manual - Page 3
...
IMPORTANT SAFETY INFORMATION
Read and understand tool labels and all of this Manual and... damage. next, pull the trigger to drive the nail. Never use this Nailer for applications other than those specified in death or serious injury. CAUTION indicates ... to drive the nail. An accident can often be driven each time the push lever is released and pressed again.
⅜ CONTACT ACTUATION...
Instruction Manual - Page 4
... protect your head from flying objects.
- 4 - OPERATORS AND OTHERS IN WORK AREA MUST WEAR SAFETY GLASSES WITH SIDE SHIELDS.
If fasteners are mistakenly driven, it contains fasteners or not. Never use of the above gases is dangerous, as a power source for the Nailer. Use only clean, dry, regulated compressed air. NEVER POINT TOOL AT...
Instruction Manual - Page 5
... AWAY. DRESS PROPERLY. Keep all work areas of unnecessary tools, debris, furniture, etc.
10. Check their condition periodically. and 3) keep the Nailer pointed downward.
17. PLACE NAILER PROPERLY ON WORKPIECE. NEVER DRIVE FASTENERS FROM BOTH SIDES OF A WALL AT THE SAME TIME. CHECK FOR LIVE WIRES. Never use the Nailer unless the push lever is removed...
Instruction Manual - Page 6
... not scratch or engrave signs on the Nailer. MAINTAIN NAILER WITH CARE.
Enforce the use ; 4) leaving work area; 5) moving it immediately and arrange for better and safer performance.
34. Continued
WARNING
25. Keep proper footing and balance at all remaining fasteners from the Nailer and removed all times.
26. The Nailer should never be operating unusually, making...
Instruction Manual - Page 7
...this Manual may show details or attachments that differ from those on your own Nailer. English
OPERATION
NOTE: The information contained in the safe operation of the valve... MECHANISM (Switching device: downward position)
Piston Piston O-Ring
Driver Blade
Nose
Adjuster
[ ] Only NR83A2 (with depth adjustment) Push Lever
Valve part
Trigger Switching Device
Valve Bush
Body
Cap Air Plug ...
Instruction Manual - Page 8
...head nails
Min.
.286" (7 mm)
Max.
.3" (7.6 mm)
2" (50 mm) 3-1/4" (83 mm)
.113" (2.9 mm)
.131" (3.3 mm)
ACCESSORIES
WARNING
ⅷ Accessories other nails can result in the Table below can be driven with this Nailer. STANDARD ACCESSORIES
1 Eye protection
1
2 Allen wrench for M8 screw
1
3 Allen wrench for M6 screw
1
1
23 4
4 Allen wrench for the NR83A2/NR83A2...nails (2 strips)
....
Instruction Manual - Page 9
...876212)
NOTE: Accessories are subject to the Nailer.
APPLICATIONS
⅜ Floor and wall framing. ⅜ Truss build-up, Window build-up. ⅜ Subflooring and roof decking. ⅜ Wall sheathing. ⅜ Mobile home and modular housing construction. WORKING ENVIRONMENT
⅜ Air compressors used . Use Hitachi pneumatic tool lubricant. Never use a non relieving coupler on...
Instruction Manual - Page 10
... table and the Air compressor size formula, find a compressor providing 6.3 CFM of Hitachi pneumatic tool lubricant into the air plug on the Nailer twice a day. Without proper lubrication, the Nailer will not work area MUST wear safety glasses with Hitachi pneumatic tool lubricant. ⅜ If a lubricator is operating properly.
COLD WEATHER CARE
⅜ Do not...
Instruction Manual - Page 11
...the length of nails and the hardness of workpiece. Next, point the nailer downward, pull the trigger and then wait in that is the same type to the upward position ...(SINGLE ACTUATION MECHANISM). (Set the switching device to be used in the actual application.
Ⅺ THE NAILER MUST OPERATE PROPERLY. Otherwise, it will not operate properly.)
Valve Bush
Switching Device Upward position
2 Hold...
Instruction Manual - Page 12
... figure.
(2) Insert nail strips one by one time. and 3) keep Nailer pointed downward.
(1) Pull the nail feeder back until it latches. Nail Feeder
NOTE: ⅷ Use nail strip at one from above the magazine.
Two strips can be loaded at least 5 nails remaining.
ⅷ Set heads of nails overlapped as shown in work area MUST wear safety...
Instruction Manual - Page 13
... 5 Remove finger from firing head when using. ⅷ Do not drive nails on the workpiece with Nailer at too steep of Operation" below. ⅷ Before starting work to be driven through the ...with a nailer operation switching device. English
WARNING
ⅷ NEVER point tool at the same time. A FULL SEQUENTIAL ACTUATION MECHANISM KIT (SEQUENTIAL TRIP MECHANISM KIT) is not in work area. ...
Instruction Manual - Page 14
...is less likely to drive an unwanted nail if you or others in work area.
ⅷ Keep hands and body away from the Nailer; 3) supply 5 - 10 drops of nails have been driven, remove...driven, completely release the trigger and lift the tool off the workpiece. 3 Depress the push lever against the workpiece to
drive a nail. 4 Move the Nailer along the workpiece with all warnings and instructions ...
Instruction Manual - Page 15
... constant
(regulator is installed and working properly), and 2) the Nailer is reached for the adjuster.
- 15 -
ALWAYS WEAR EYE PROTECTION. Perform a nailing test.
5 DISCONNECT AIR HOSE FROM NAILER. 6 Choose a suitable position for a nailing test.
4 Connect the air hose. ADJUSTING THE NAILING DEPTH
[Only NR83A2 (with depth adjustment)]
WARNING
ⅷ Disconnect the air hose from...
Instruction Manual - Page 16
... trained by Hitachi, distributor or employer shall repair the Nailer.
ⅷ Use only parts supplied or recommended by an...Nailer. If not smooth, nails can be carried out by Hitachi for an extended period, apply a thin coat of Hitachi Power Tools must be helpful if presented with the tool to incorporate the latest technological advancements.
Lubricate it with Hitachi pneumatic tool...
Instruction Manual - Page 17
... lubricator filled. Keep push lever working properly.
Supply 5 - 10 drops of moisture and dirt.
PROBLEM Nailer operates, but does not drive ...damaged?
Ribbon spring weakend or damaged?
--- Use Hitachi pneumatic tool lubricant. Clean magazine and feeder mechanism. Drain air compressor. Keep the Nailer operated properly.
Skipping nails. Check air pressure. Driver blade worn...
Parts List - Page 2
...(F)
1
7 877-328 EXHAUST PIECE
1
8 877-854 GASKET (C)
1
9 884-110 EXHAUST VALVE (ORANGE)
1
10 877-307 HEAD CAP AND GASKET SET
1 INCLUD. 8
11
877-368 O-RING (1AP-48)
1
12 877-323 PISTON
1
13 877-316 O-...WASHER
1
22 877-310 CYLINDER GUIDE
1
23 877-327 GASKET (G)
1
24 884-069 WARNING LABEL
1
25 883-506 BODY ASS'Y
1 INCLUD. 38
26 877-315 CYLINDER O-RING (I.D 63.9)
1
27 883-511...
Parts List - Page 4
... 6MM
502 944-459 HEX.
DESCRIPTION
601 881-768 GRIP TAPE (A)
602 880-407 TAPE
603 877-153 PNEUMATIC TOOL LUBRICANT (30CC)
604 874-042 PNEUMATIC TOOL LUBRICANT (120CC)
605 876-212 PNEUMATIC TOOL LUBRICANT (1L)
606 317-918 GREASE (ATTOLUB NO.2) 500G
NO. USED
1 1 1 1 1 1
REMARKS
NR 83A2
OPTIONAL ACCESSORIES
ITEM NO. CODE...
Similar Questions
My Hitachi Split Ac 6years Old Red Light 7 Times Blinking Kindly Help Any One
(Posted by rameshchithirai651 4 years ago)
Hitachi Framing Nailer Nr83a
My framing nailer fires two nails at a time . What can I do to solve the problem?
My framing nailer fires two nails at a time . What can I do to solve the problem?
(Posted by rahundl 5 years ago)
My Hitachi Ac's Is Not Working. Red Led Is Blinking 7 Times. What's The Problem?
(Posted by arunamozhi 9 years ago)
What Is The Difference Between Hitachi Nr90ad(s) & Nr90adpr?
What is the difference between Hitachi Nr90AD(s) & Nr90ADPR?
What is the difference between Hitachi Nr90AD(s) & Nr90ADPR?
(Posted by justinvella30 10 years ago)
Hitachi Gas Strip Nailer
I AM TRYING TO FIND A PART CALLED A ,FUEL CELL ADAPTER
I AM TRYING TO FIND A PART CALLED A ,FUEL CELL ADAPTER
(Posted by scottmacaulay987 11 years ago)