HP P2000 Support Question
HP P2000 Support Question
Find answers below for this question about HP P2000.Need a HP P2000 manual? We have 30 online manuals for this item!
Question posted by zacki on March 6th, 2014
How To Configure Microsoft Iscsi Initiator For Mpio On Hp P2000
The person who posted this question about this HP product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related HP P2000 Manual Pages
HP StorageWorks P2000 G3 MSA System MPIO DSM Installation Guide (590337-003, February 2010) - Page 5
... MPIO DSM and the MPIO DSM included with the Microsoft iSCSI Software Initiator can be obvious and you can safely substitute what you see on your computer for managing multipathing on the same server if both HP StorageWorks P2000 G3 systems and HP StorageWorks MSA200 G1 and G2 systems, the installation instructions differ between the server and the storage device...
HP StorageWorks P2000 G3 MSA System MPIO DSM Installation Guide (590337-003, February 2010) - Page 9
... are installed. IMPORTANT: The MSA System MPIO DSM also does not apply to the HP StorageWorks P2000 G3 MSA System FC/iSCSI storage controller if the server is not supported. Connecting both iSCSI and FC ports to the same server is connected to install and configure the MSA System MPIO DSM for iSCSI. Windows Server 2003
This section describes...
HP StorageWorks P2000 G3 MSA System MPIO DSM Installation Guide (590337-003, February 2010) - Page 10
... Large Numbers of devices depends on the Installation Instructions and Release Notes
tabs before downloading and installing the software. Some operations can take several seconds per LUN per path.
1. Run the executable downloaded from http://www.hp.com/go/p2000. 2.
See "Long Failover Times When Using MPIO with a large number of LUNs, configure your product...
HP P2000 G3 1GbE iSCSI MSA and 10GbE iSCSI MSA Controller Firmware TS230R044 Release Notes - Page 3
...) • TS210R016 (For the HP P2000 G3 10GbE iSCSI MSA controller)
Product models
HP P2000 G3 MSA System controllers: • HP P2000 G3 10GbE iSCSI MSA Array System Controller (P2000 G3 10GbE iSCSI MSA
Controller) • HP P2000 G3 1GbE iSCSI MSA Array System Controller (P2000 G3 1GbE iSCSI MSA Controller)
Additional devices
HP Drive Enclosures: • HP P2000 LFF Drive Enclosure, firmware...
HP P2000 G3 MSA System CLI Reference Guide - Page 11
...guide
This guide provides information about managing an HP P2000 G3 MSA System by using this product include knowledge of: • Network administration • Storage system configuration • Storage area network (SAN) management and direct attach storage (DAS) • Fibre Channel, Serial Attached SCSI (SAS), Internet SCSI (iSCSI), and Ethernet protocols
Related documentation
In addition...
HP P2000 G3 MSA System CLI Reference Guide - Page 43
... storage system's IQN, use the show iscsi-parameters
HP P2000 G3 MSA System CLI Reference Guide 43 A storage system's secret is enabled, the record enables authentication between the originator (initiator) ...host initiator: # create chap-record name iqn.1991-05.com.microsoft:myhost.domain secret 123456abcDEF Success: Command completed successfully. -
create chap-record
Description For iSCSI, ...
HP P2000 G3 MSA System Event Description Reference Guide - Page 31
...discovery and initialization of pings that passed and the number
that failed. An iSCSI ping operation...controller module's
HIM has a Broadcom PBC.
HP P2000 G3 MSA System Event Descriptions Reference Guide 31...is used. Recommended actions • Check that the storage system's fans are running. • Check that... configuration.
Recommended actions • No action required.
311
Info...
HP P2000 G3 MSA System SMU Reference Guide - Page 13
... HP P2000 G3 MSA System FC/iSCSI User Guide • HP P2000 G3 MSA System SAS User Guide • HP P2000 G3 iSCSI MSA System iSCSI User Guide • HP P2000 G3 MSA System CLI Reference Guide • HP P2000 G3 MSA System Event Descriptions Reference Guide You can find these documents from the Manuals page of : • Network administration • Storage system configuration • Storage...
HP P2000 G3 MSA System SMU Reference Guide - Page 23
... can be added. HP P2000 G3 MSA System SMU Reference Guide 23 A storage system with read ... exposures.
• Define the CHAP secret(s) in configuring CHAP entries for new hosts. You can specify read...storage system. For example, a payroll volume could be masked for the Human Resources host and be mapped with no access through which can also be useful in the host iSCSI initiator...
HP P2000 G3 MSA System SMU Reference Guide - Page 81
...HP P2000 G3 MSA System SMU Reference Guide 81 Click Reset Host Port. A manual rescan is not working properly and you cannot determine why, you are online and leftover disks exist. To rescan disk channels 1.
For a Fibre Channel host port configured...; Resetting a host port
Making a configuration or cabling change on a host might cause the storage system to use this command, contact ...
HP P2000 G3 MSA System SMU Reference Guide - Page 83
... of a vdisk by deleting the vdisk. If the task succeeds, verify that the storage system supports. Before starting a vdisk expansion, read the white paper "HP P2000 G3 MSA Best Practices" at a time.
NOTE: If an iSCSI port is connected to a Microsoft Windows host, the following event is recorded in write cache to disk.
To perform...
HP StorageWorks P2000 G3 FC and FC/iSCSI MSA Controller Firmware Release Notes (631269-003, December 2010) - Page 11
...serial number is now correctly displayed. • show configuration-Information about all types of system volumes; HP StorageWorks P2000 G3 FC and FC/iSCSI MSA Controller Firmware Release Notes 11 If the bus...topic at http://technet.microsoft.com/en-us/library/dd163558.aspx.
• Failover time is affected by restart sc both followed by the number of attached storage enclosures is now ...
HP StorageWorks P2000 G3 iSCSI MSA System Controller Firmware Release Notes (635662-001, November 2010) - Page 4
... to use the IQN setup to remove a host that is addressed by the iSCSI Software Initiator, but must have firmware 2.18 installed. Workaround: Access 128 LUNs or less via the Qlogic iSCSI HBA when using a Qlogic iSCSI HBA in boot-from -storage configuration. Issue: One host remains when three or more than 128 LUNs using the...
HP P2000 G3 MSA Systems Installation Instructions - Page 1
Install hardware options" (page 1)
"Step 3. Configure the MSA" (page 6)
Step 2. The following controllers:
• HP P2000 G3 Fibre Channel MSA Controller
• HP P2000 G3 Combo FC/iSCSI MSA Controller
• HP P2000 G3 SAS MSA Controller
• HP P2000 G3 10GbE iSCSI MSA Controller
• HP P2000 G3 iSCSI MSA Controller
Installing an HP P2000 G3 MSA System includes:
"Step 1. ...
HP P2000 G3 MSA Systems Installation Instructions - Page 6
... panel and select Tools > Update Firmware. Using the Storage Management Utility (SMU), right-click the system in the P2000 G3 MSA array controller.
Configure the MSA
See the HP P2000 G3 MSA System User Guide, HP P2000 G3 MSA System Reference Guide, and HP P2000 G3 MSA System Cable Configuration Guide for the Safety and Disposal guide located on the...
HP StorageWorks MSA System MPIO DSM Installation Guide (590337-005, September 2010) - Page 5
... Array (iSCSI), the required MPIO DSM is support for information on the same server if both HP StorageWorks P2000 G3 systems and HP StorageWorks MSA200 G1 and G2 systems, the installation instructions differ between the server and the storage device.
In all covered by -side on how to verify installation is included, although no further configuration is required...
HP StorageWorks MSA System MPIO DSM Installation Guide (590337-005, September 2010) - Page 6
... 20 for HP
StorageWorks P2000 G3 systems" on page 8. If you are installing for HP P2000 G3 storage, open a command prompt window and run the following steps to install and configure the native MPIO DSM included with a large number of LUNs, configure your Windows Server Registry to use a larger PDORemovePeriod setting. • If you are using an iSCSI connection...
HP StorageWorks MSA System MPIO DSM Installation Guide (590337-005, September 2010) - Page 10
The Microsoft iSCSI Software Initiator includes the MPIO DSM that is not supported. However, both iSCSI and FC ports to the host. NOTE: The time it takes to complete MPIO DSM installation, initial scan, and detection of devices depends on the complexity of the system configuration, the number of LUNs, and the number of devices connected to the same server is...
HP StorageWorks P2000 G3 FC MSA Dual Controller Small Business SAN Starter Kit Installation Overview (617351-001, June 2010) - Page 2
...cost to initially configure the switch and storage array.
Access the Storage Management Utility (SMU) for the array enclosure to P2000 G3 array enclosure. 7. Key System information
Record the following key configuration tasks:
• Setting the switch IP address. • Setting the switch password. • Configuring switch zones and performing device selection. • Configuring system...
HP BladeSystem Deployment Guide for Solutions with 6Gb SAS Switches and External SAS Storage - Page 45
... displayed as a boot device for HP BladeSystem and HP MSA2000sa on the MSA. The WWNs of installing the BladeSystem solution are complete. If the MSA is used in the SMU or CLI when granting hosts access to the storage. Enter P2000 G3 SAS MSA Array system parameters. ("Configuring the system" in the HP P2000 G3 MSA System SMU...
Similar Questions
Hp P2000 G3 Iscsi How Many Mib
(Posted by ghoENG 9 years ago)
I Need Drive For Hp 2000 G3 For Win2003 X64 For Hp P2000 G3 Fc\scsienclosure Dev
I need drive for hp 2000 G3 for win2003 x64 for hp p2000 g3 fc\scsienclosure device?
I need drive for hp 2000 G3 for win2003 x64 for hp p2000 g3 fc\scsienclosure device?
(Posted by MUNEEB 12 years ago)