Hayward TigerShark Support Question
Hayward TigerShark Support Question
Find answers below for this question about Hayward TigerShark.Need a Hayward TigerShark manual? We have 2 online manuals for this item!
Question posted by sallyrob4 on July 16th, 2011
Cleaning Problem
Our tigershark cleans well...the problem is that it is only cleaning the side of the pool on which it is plugged. We untangle the cord when we put it in the water but it is still only cleaning the side of the pool next to the plug.
Current Answers
Related Hayward TigerShark Manual Pages
All Models - Page 1
... Address City State___________Zip Date Purchased Is this replacing another pool vacuum? Aqua Vac Pool Cleaners, Inc. 1711 Longwood Road West Palm Beach,... Purchased from City State___________Zip The size of my pool surface is___________x__________ Surface is Have you seen us on the web at www.aquavacsystems.com
Serial TigerShark (Located inside filter area)
Registration of Warranty This...
All Models - Page 3
... factory rebuilt identical or reasonably equivalent unit or part, in material and workmanship. Accordingly, Aqua Vac Pool Cleaners, Inc. This limited warranty is valid and enforceable only in the United States of America on Tigersharks that are owned and operated in this warranty will not apply and that reimbursement for the nearest...
All Models - Page 5
... Information 6 General Operating Instructions....6 TigerShark QC, Plus and 2 Plus Operating Instructions 8 Remote Control Trouble Shooting.. 9 Machine Assembly/Parts............10 Maintenance 11 Trouble Shooting 12 Specifications 13 Figures 14-17 Safety Precautions 18 Preventative Maintenance.........19 Parts Ordering Instructions........19
The World's Best Pool Cleaners For More Than 40...
All Models - Page 6
... Seek Control Logic (ASCL®) Microprocessor control optimizes cleaning routine for each use and/or operation of the TigerShark.
1. GENERAL INFORMATION
Congratulations on your purchase of 11.5 feet from any and all claims for damages to any pool plaster or vinyl liner in combination with, age, incorrect pool water chemistry, improper installation, and other factors.
All Models - Page 7
... and switch to the pump & drive motor seals, which will go into Quick Clean cycle. After the pool has been cleaned, switch OFF the power supply before starting the cleaning cycle. Remove the TigerShark from the water at the shallow end of the water using the handle, NOT the cable. Caution: When pulling the cable, reel it...
All Models - Page 8
... the General
Operating Instructions located on , and then the Full cycle can be operated at any time without disrupting the cleaning cycle.
3. The TigerShark QC pool cleaner will resume its programed operation. 8 The Full Clean cycle will be turned off and back on page 6. This is complete, the on / off power switch must be...
All Models - Page 9
... work foot in water for at least 15...not the unit. To reset depress the small black button located above the flotation cord connection on the front of the power supply may be lodged with foam rollers,... tripped. Turn cleaner off and remove from the pool. HAND HELD REMOTE CONTROL
Troubleshooting the remote control function
If the TigerShark Plus does not turn when the remote control is...
All Models - Page 11
... lock position. • Filter cleaning solution can be checked periodically for thorough cleaning. Remember: The cleaner your cleaner will then circle the pool in a dry, shady location at temperatures between the tracks (10) and wheels (11). e).
• Pull out the filter cartridge.
Storage When out of the water, store TigerShark on its side in the...
All Models - Page 12
... additional information.
12 FAQS" at our website for debris and clean if necessary. • TigerShark is out of the water. Such items can be clogged. • An optional high velocity inlet is available from your pool. c).
Check and clean if necessary following the instructions in water and reset the power. You may be sure all chemical...
All Models - Page 13
...Cleaning Cycle
3 hrs (7 hrs for TigerShark2®)
Drive System Direct Drive w/Polyurethane Drive Track & Acetal/Stainless Steel Bearing System
Power Supply Primary Voltage Secondary Voltage Rated Output Current Weight
110-120 volt AC (220-240 volts for TigerShark....3 cm)
13 Shipping Carton Dimensions Shipping Weight
Tigershark/TigerShark 2 Height 19 in. (48.3 cm) ...
All Models - Page 18
... outlet.
2. THIS CAN ALSO IMPROVE THE OPERATING LIFE OF YOUR TIGERSHARK .
3. NEVER ALLOW PLUG TO ENTER THE POOL.
8. THIS WILL DAMAGE THE MOTOR SEAL AND VOID THE WARRANTY.
9. DO NOT OPERATE THE MACHINE OUT OF WATER. REPLACE DAMAGED CORDS.
12. WARNING - DO NOT USE AN EXTENSION CORD.
After use, remove the unit and rinse with fresh...
All Models - Page 19
...TigerShark. matically. • Remove any questions, contact your local Service Center or call Aqua Vac Systems, 1-800-327-0141 or 561-688-0211. Laying cord, straightened out in sunlight is
functioning properly. Friday, 8:30 a.m. - 5:30 p.m. If you have any twists in the water...; Thoroughly rinse entire unit after use. • Clean filters thoroughly after each use . Replace when...
All Models - Page 3
...use with permanently-installed pools and may also have the problem corrected by a GFCI. The pump...Pool Products 620 Division Street
Elizabeth, NJ 07201
Page 3 of any electrical equipment, turn OFF power to the equipment. TigerShark Plus and TigerShark...cord to connect unit to pool structure will apply. To obtain warranty service, please contact the place of swimming pool, spa...
All Models - Page 5
... shade. Submersing by pulling the cable until the TigerShark reaches the
surface. The TigerShark will go into Quik Clean cycle. This may result in damage to minimize cord twisting.
5. After the pool has been cleaned, switch OFF the power supply before starting the cleaning cycle.
Remove the TigerShark from the pool edge (page 13 Fig. Throughout this manual reference...
All Models - Page 6
...USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
ROBOTIC POOL CLEANER
ISRC10202 REV C Page 6 of the restrictor plate. If your TigerShark's filter is still climbing too high. ...pool and observe the waterline climbing height. Restrictor insert may be corrected by placing restrictor plate in the slot and rotate clock
wise to go through
several cycles so that you can be needed if cleaner is clean...
All Models - Page 7
... initially switched on / off power switch must be selected.
For the best operation of the Remote Control.
The TigerShark QC pool cleaner will automatically shutoff in the front of the desired cleaning cycle.
2. The Full Clean cycle will resume its programmed operation. For installation, setup and general operation information refer to the General Operating...
All Models - Page 10
...cord is out of the bottom lid. • Replace the filter cartridge into lock position. • Filter cleaning solution can be checked periodically for thorough cleaning. f). • Wash the inside of the water... or may become coiled (like a telephone cord). MAINTENANCE
Clean the filter cartridge after each use: • Place the TigerShark on its service agent, or a similarly ...
All Models - Page 11
... climb pool walls: • Clean the filter. If TigerShark fails to the bottom lid. c) Clip the high velocity inlet to pick up fine or heavy debris: • Clean the filter. This part also can jam the
cleaner and cause damage to the unit and/or your pool. Page 11 of the water. Replace worn brushes (page...
All Models - Page 12
... w/auto-shutoff.
Shipping
Carton Dimensions
Shipping Weight
TigerShark Height 21 in. (53.3 cm) Width 20 in. (50.8 cm) Length 20 in different swimming pools and electrical supply outlets.
Filter
Type Media
Removable, Re-Usable, Pleated Element Cartridge Pleated Cellulose/Polyester Blend
Cleaning Routine Control
Type Cleaning Cycle
Adaptive Seek Control Logic (ASCL®) Microprocessor...
All Models - Page 15
...Clean filters thoroughly after each use-a clogged filter can decrease efficiency dramatically. • Remove any twists in the water. • Inspect belts and filters frequently. be minimal if the unit is helpful. • Avoid allowing the unit to "cool down" in the cord...HAYWARD GENUINE REPLACEMENT PARTS
ROBOTIC POOL CLEANER
ISRC10202 REV C
EST... of the TigerShark serial number and...
Similar Questions
Cleaning Flex Tubes
do i need to remove flex tubes to clean or what needs to be done to clean properly
do i need to remove flex tubes to clean or what needs to be done to clean properly
(Posted by garbopp 9 years ago)
How To Change The Impeller In My Tigershark Pool Cleaner
(Posted by moaws181 10 years ago)
Tigershark Not Goes Up The Walls Anymore
My shark doesnt claim the walls and do not clean the pool so great. What I should replace?
My shark doesnt claim the walls and do not clean the pool so great. What I should replace?
(Posted by monicamirea 10 years ago)
Tigershark Rc9950 Repair
Where can I get my TigerShark RC9950 repaired? I am in Providence, RI. Thanks.
Where can I get my TigerShark RC9950 repaired? I am in Providence, RI. Thanks.
(Posted by yswan 11 years ago)