Home » Hayward » Pool & Spa » Hayward Super Pump VS

Hayward Super Pump VS Support Question

Find answers below for this question about Hayward Super Pump VS.
Need a Hayward Super Pump VS manual? We have 1 online manual for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by mlgaudette on July 2nd, 2016

Error Code Xx, How Do I Fix It?

New pump worked yesterday not working today, error code is XX.

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by tfarner7 on July 2nd, 2016 11:45 AM

This answer was accepted by the poster of the original question.

tfarner7

Member since:
April 2nd, 2011

Points: 429,890

1,100
points

From the Manual... Error Code XX - Indicates that the user interface is receiving an error from the motor/drive that it does not understand. Contact Hayward Technical Service for additional assistance.

Their contact information is:

Hayward Pool Products

620 Division St, Elizabeth, NJ 07201

Phone: (908) 351-5400

www.haywardpool.com

Related Hayward Super Pump VS Manual Pages

Super Pump® VS Manual - Page 1

... REFERER AU SITE WEB HAYWARDPOOL.CA POUR LES INSTRUCTIONS EN FRANCAIS Super Pump® VS Owner's Manual IS2600VSP Rev C Model SP2600VSP Super Pump Variable Speed Pump The Hayward Super Pump VS is specifically engineered for the demanding requirements of today's inground swimming pool/spa that is a self-priming pump that incorporates an improved seal and impeller design that will provide...

Super Pump® VS Manual - Page 2

... Error Display 16 6.10. Storing Pump For Winterization 17 9. Removing the Ceramic Seat 18 9.4. Parts Diagram 19 11. General Information ...7 2.1. Pump Location 8 4.2. User Interface Summary 12 6.4. Menu Outline 13 6.5. Maintenance...17 8. Shaft Seal Change Instructions ...18 9.1. Table of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump...

Super Pump® VS Manual - Page 4

.... A storable pool is constructed so that will or can also make consumers aware of being readily disassembled for personal injury. Though this manual, look for one that it is strongly advised to its original integrity. It requires free circulation of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev...

Super Pump® VS Manual - Page 5

..., or unsecured cause severe injury and/or death due to pool structure will increase risk for bonding requirements. Before working on a routine basis. Failure to bond pump to the following entrapment hazards (symbols complements of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C Mechanical Entrapment - All components should be caught...

Super Pump® VS Manual - Page 6

... system. SAVE THESE INSTRUCTIONS Page 6 of pump components. Before servicing pool and spa water circulation system, all national, state, and local codes applicable.  Installation of water (not...could result in violent separation of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C floor or wall), must be set in the system,...

Super Pump® VS Manual - Page 7

The Super Pump VS displays power consumption in this information, you can drastically reduce the power that is also designed to Kilowatts: 370 W = 0.370 kW 0.370 kW X $0.10/kWh = $0.04 per Hour Example: Super Pump Variable Speed Pump operating at lower speeds. Primary Features Totally enclosed, permanent magnet motor Advanced hydraulic design Fully programmable with up to...

Super Pump® VS Manual - Page 8

...pump, you filter ("turnover") all local and national codes. After setting the pump speed(s), it is adequately flowing over -tightened). Pump Location Locate pump as close to water level as possible to reduce friction loss. Do NOT install pump...on equipment (e.g. Running the pump at a lower speed may require running the pump for a longer period of time in the pool at a low speed for...

Super Pump® VS Manual - Page 9

... end of Plumbing and Mechanical Officials (IAPMO) standards. 4.5. The pump suction and outlet ports have molded-in severe personal injury or death. 4.4. Pool and spa fittings MUST conform to handle the maximum flow required. When installing the Super Pump VS, care should be used between the pump suction inlet and any plumbing fittings (elbows, valves, etc.). Use...

Super Pump® VS Manual - Page 10

... wires going to circuit. Pump MUST be careful not to pull on the motor housing and to all metal parts of swimming pool, spa, or hot tub, and to all electrical equipment, metal piping (except gas piping), and conduit within and around the pool with local codes, regulations, and the National Electric Code (NEC). Installation Procedure...

Super Pump® VS Manual - Page 11

...is discharged from pump and/or filter and proceed with water to the pool bonding system using the filter manual air relief valve, before removing pump strainer cover. If...pump to suction pipe level. Wiring Diagrams 5.1. Return to filter to close filter manual air relief valve when a steady stream of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump ...

Super Pump® VS Manual - Page 12

... length of suction pipe. NOTE - Turn on power and wait for pump to prime, which can take up the two hand knobs and turn clockwise to pool/spa system directly in front of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C See Troubleshooting Guide. 6.3. ATTENTION - See filter owner's manual for...

Super Pump® VS Manual - Page 13

...USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C Screen Buttons Used Comments  DISP/FUNC Pump software revision number will illuminate to save the new speed setting. 1. Menu/navigation buttons: The DISP/FUNC button will FLASH. 4. V1 Speed c. V3 Speed f. When a speed is experiencing an error. Preset Speed settings can be...

Super Pump® VS Manual - Page 14

... the Configuration Menu. 6.6. At this time to temporarily run the pump, however, it is in Prime Mode the Prime mode Timer will... mode ▲▼ DISP/FUNC Adjust the time of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C Configuration Menu Screen Buttons Used DISP/FUNC Comments Press & Hold button for several seconds...

Super Pump® VS Manual - Page 15

...the LED for speeds V2 and V3 is 3,000 RPM. If configuration mode is not saved, the pump will continue to run at the changed speed until the timer runs out for the speed being configured ... of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C If the new speed setting is not completely exited after 2 minutes, the controller will FLASH.

Super Pump® VS Manual - Page 16

... error codes can be displayed. To exit from the pump. Error Display Screen Buttons Used Comments Note: If an Internal Failure has been detected the pump will resume the pump. 6.10. The cause of test mode Cycle through to the next screen Note: When troubleshooting the pump it may be investigated and fixed before continuing to run the pump...

Super Pump® VS Manual - Page 17

...reset all settings back to motor before draining pump. Once the pump is fully drained of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C Maintenance  Clean strainer...Hold RUN/STOP and apply power to the pump Note: The pump may be replaced, due to freeze with water in your pool/spa system. Insure motor air vents are highly toxic...

Super Pump® VS Manual - Page 20

...basket, and refill the strainer housing with the wiring diagram on the pool wall. 3. Part No. Be sure the pump is locked firmly in the cover gasket groove. tripped circuit breakers,...Check for free movement and lack of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C Description Qty. Have a qualified repair professional open switches or ...

Super Pump® VS Manual - Page 21

... as per manufacturer's instructions; Replace the impeller including a new seal assembly.  Noisy Pump: 1. Vibration due to check by removing the skimmer basket...Super Pump Variable Speed Pump IS2600VSP Rev C filters - Air leak in pool, and unrestricted discharge return lines. Sand filters - Cartridge filters - Mount the pump on a level surface and secure the pump...

Super Pump® VS Manual - Page 22

... and resolved before continuing normal operation of 24 USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump Variable Speed Pump IS2600VSP Rev C Warranty Page 22 of the pump. 11.2. When the issue has been resolved, press the RUN / STOP key to clear the error message. Error Codes In the case that an internal failure has been detected the...

Super Pump® VS Manual - Page 24

... dealer or an experienced radio/television technician for : In Ground Spa Replacement is a registered trademark and Super Pump VS is encouraged to try to : Hayward Pool Products, 620 Division Street, Elizabeth, NJ 07207 Attn: Warranty Dept Or REGISTER YOUR WARRANTY ON-LINE AT WWW.HAYWARDPOOL.COM New Installation Installation for additional suggestions. However, there is subjected...