Hayward Super Pump Support Question
Hayward Super Pump Support Question
Find answers below for this question about Hayward Super Pump.Need a Hayward Super Pump manual? We have 2 online manuals for this item!
Question posted by pdavis188 on June 15th, 2012
What Size Are These Screws Motor Cap Screw 4 Spx125z4 ?
what size are these screws MOTOR CAP SCREW 4 SPX125Z4 ?
Current Answers
Related Hayward Super Pump Manual Pages
All Super Pump models - Page 1
...MUST complete, in full, all electrical installations noted in -ground swimming pool/spa that is a self-priming pump that incorporates an improved seal and impeller design that will provide many ... IN SERIOUS INJURY.
The Super is equipped with large capacity filters, heaters, and pool cleaning equipment.
Super Pump™ Series
The Hayward Super PumpTM is specifically engineered for...
All Super Pump models - Page 2
.... Pool and spa components have a finite life.
CAUTION warns about hazards that are alert to protect the electrical components from using them as the filtration system, pumps, and heaters must be readily disassembled for personal injury.
All components should always be inspected frequently and replaced at all instructions in a damp or nonventilated location. Super Pump...
All Super Pump models - Page 3
...Installation of swimming pool, spa, or hot tub. Before working on pump or motor, turn off power supply to pool structure will ...suction outlet cover resulting in an entrapment. For size of swimming pool, spa, or hot tub, and to , grounding...hedge trimmers and other general wiring procedures. Mechanical Entrapment-
Super Pump™ Series _____ _____
_____
_____
Page 3 of
...
All Super Pump models - Page 4
... starting the circulation system. Do not operate pool and spa circulation system if a system component is not designed to do so could result in severe personal injury and/or property damage. WARNING - Failure to install according to 48 and 56 frame motors. ƒ Heat resistant, industrial size ceramic seal. ƒ Rugged, one-piece housing...
All Super Pump models - Page 5
...electrical components from the weather. Super Pump ™ Series__________
Product Specifications
...screws or bolts to reduce friction loss. No system should have continuous slope upward from excess moisture and flooding. ƒ Allow adequate access for gate valves in suction and discharge piping. ƒ Be protected from lowest point in a damp or non-ventilated location.
Pipe Sizing...
All Super Pump models - Page 6
...cause cracking of the male fitting with the motor's voltage, phase, and cycle, and that could cause an air trap. Pool and spa fittings MUST conform to inspect and repair ...and/or components may cause damage. Fire Hazard. Super Pump ™ Series __________ Pump Mounting (cont'd)
_____
Page 6 of a
swimming pool filtration system operate under pressure. Hazardous Pressure. Do ...
All Super Pump models - Page 7
... conduit within and around the pool with water before proceeding. 2. NEVER run pump dry.
Super Pump ™ Series _ _________
_____
Page 7 of 15
Electrical (cont'd.)
Voltage
Voltage at full load, consult Power Company. If voltage is running at motor MUST NOT be permanently connected to GFCI. Do NOT add chemicals to pool/spa system directly in suction...
All Super Pump models - Page 8
... of suction lift and horizontal length of
motor and consequent serious pump damage. Be sure all suction and discharge valves are opened. See Troubleshooting Guide. ATTENTION -
Maintenance
ƒ Clean strainer basket regularly. See "Shaft Seal Change Instructions" in your pool/spa system. Separation Hazard. ATTENTION - Allowing the pump to prime, which may damage plastic components...
All Super Pump models - Page 9
Drain water level below all inlets to the pump/strainer housing.
2.
D.
Remove the four (4) 3/8" x 2" housing cap screws which hold the motor assembly to the pool. 2. The spring portion of 15
WARNING -
If tight, use extension cords. Clean all electrical power service to use this manual for swimming pool pump installation.
To avoid dangerous or fatal electrical shock ...
All Super Pump models - Page 10
... on page 11 of this manual for pump component locations.)
8. Fasten motor end cover by holding motor shaft with a clean, soft, cotton cloth.
Tighten snugly by using the four (4) 3/8"" x 2" housing cap screws. (Be sure housing gasket is in step #4.
13. WWW.HAYWARDPOOL.COM
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS Super Pump ™ Series
Page 10 of 15...
All Super Pump models - Page 11
Super Pump ™ Series
Replacement Parts
Parts Diagram
Page 11 of 15
Parts Listing...CAP SCREW
16
MOTOR CAP SCREW
MOUNTING FOOT [WILL
INCLUDE ADAPTER (19) AND
17
SCREWS(18)]
4
SPX1600Z4 SPX1600Z4 SPX1600Z4 SPX1600Z4 SPX1600Z4 SPX1600Z4
4
SPX125Z4 SPX125Z4 SPX125Z4 SPX125Z4 SPX125Z4 SPX125Z4
1
SPX2600G1 SPX2600G1 SPX2600G1 SPX2600G1 SPX2600G1 SPX2600G1
18
MOUNTING FOOT CAP SCREW...
All Super Pump models - Page 12
...switches or relays; Loose connections on pool wall. 3. Leaking O-ring or packing glands on motor data plate label.
If pump does not develop a vacuum and pump has sufficient "priming water": i. Check... b. Re-check strainer housing cover and all threaded connections for debris. Low Flow - Super Pump ™ Series
Troubleshooting
Page 12 of vacuum at the strainer cover (Only your hand...
All Super Pump models - Page 13
.... Motor bearings noisy from return fittings). Plugged or restricted discharge line of 15
Low Flow - Solution: Re-tighten using Teflon tape. 5. Air leak in a smaller eyeball fitting. 2. Undersized pool piping. Loose stones/debris hitting impeller could be replaced at any joint, low water level in pump housing. Solution: Replace including new seal assembly.
D.E. Super Pump...
All Super Pump models - Page 14
... the nearest authorized Hayward service center. All other such costs incurred in association with an automatic valving system, shall be responsible for your records. Hayward Pool Products, Inc. 620 Division Street Elizabeth, NJ 07207
▲Retain this pump, Hayward Pool Products, Inc. Super Pump ™ Series
___ Page 14 of the standard warranty apply.
All Super Pump models - Page 15
... Address City State_________ Zip E-mail Address
Product Purchased Product Serial No
□ New Installation
□ Replacement
Type of In-Ground Pool:
□ Vinyl □ Fiberglass □ Gunite
Size of purchase/installation. Super Pump ™ Series
___
Page 15 of 15
▼DETACH HERE: Fill out bottom portion completely and mail within 10 days of...
Parts Guide - Page 1
... Pump Models: SP1600X5, SP1605X7, SP1607X10, SP1608X10, SP1610X15, SP1611X15, SP1615X20, SP1616X20, SP1621X25
4
6
5
7
16 13
11 12 14 18
17 10
8
2 3 15
9
1
MOUNTING FOOT
Ref.
SPX1600Z52
Mounting Foot Cap Screw (Set of 2 - 2 Sets Required)
1
10
SPX1600Z2
Seal Assembly
10
11
SPX1600F5
Motor Mounting Plate
10
12
SPX1600Z4
Housing Cap Screw
10
13
SPX0125Z44
Motor Cap...
Parts Guide - Page 2
...Pump Housing/Strainer, 2" x 2", with Adapter and Screws
-
SPX1600Z52
Mounting Foot Cap Screw (Set of 2 - 1995 and Prior, 2 sets required)
10
SPX1600Z2
Seal Assembly
11
SPX1600F5
Motor Mounting Plate
12
SPX1600Z4
Housing Cap Screw
13
SPX0125Z44
Motor Cap Screw...1 1 1 1 1 1 1 1 1 1 Pumps
Super Pump®
SP2600X PUMP SERIES (MAX-RATED) REPLACEMENT PARTS
Parts for 2 1/2 H.P. only
...
Similar Questions
What Are The Valve Settings For Inground Pool With Hayward Max Xl Flo Pump
(Posted by Anonymous-174361 10 months ago)
How Do We Find Screw For Shaft
pump ceased up where is shaft screw
pump ceased up where is shaft screw
(Posted by traceysoltis 6 years ago)
What Size Are The Hayward Super Pump Series 1600 Motor Cap Screws?
(Posted by tomhans82 10 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)