Hayward SharkVAC XL Support Question
Hayward SharkVAC XL Support Question
Find answers below for this question about Hayward SharkVAC XL.Need a Hayward SharkVAC XL manual? We have 1 online manual for this item!
Question posted by puons on May 14th, 2020
Drive Sharkvac?
HelloHow Can i change drive belt on y sharkvac?
Current Answers
Answer #1: Posted by freginold on May 14th, 2020 2:55 PM
freginold
Member since:
December 20th, 2011 Points: 23,253,985
Member since:
December 20th, 2011 Points: 23,253,985
Hayward's Robotic Cleaner Troubleshooting Guide shows you how to replace the belt. (Specifically, see page 13.)
Related Hayward SharkVAC XL Manual Pages
Model: SharkVac XL - Page 2
... that are unpredictable and unsafe. It can cause minor or moderate personal injury and/or property damage and if ignored presents a potential hazard.
ISRC9740XLN Rev C
SharkVAC XL™ / e.VAC PRO™
by
Owner's Manual
Contents
Warnings 3 Information 5 Operating Instructions 7 Maintenance 11 Troubleshooting 17 Warranty Registration 22
IMPORTANT SAFETY INSTRUCTIONS
Basic safety...
Model: SharkVac XL - Page 3
...
CPSC guidelines, follow safety and operation instructions could result in violent separation of the pool/spa from the
suction outlets can result in mechanical entrapment. Body Suction Entrapment- WARNING ...:
Hair Entrapment- Do not change the filter control valve position while the pump is recommended. Separation Hazard. Before servicing pool and spa circulation system, filters manual air...
Model: SharkVac XL - Page 4
...reassembled to all electrical equipment before using. WARNING - Electrical ground all metal parts of swimming pool, spa, or hot tub, and metal piping (except gas piping), and conduit within 90 days ... warranties of purchase is in this manner, the GFCI is required for a period of swimming pool, spa, or hot tub. For assistance on how to electric supply.
WARNING - In the event ...
Model: SharkVac XL - Page 5
...CONSUMER INFORMATION AND SAFETY
Risk of warranty. DO NOT switch the pool cleaner to allow a safety distance between the power supply and the pool as
required by the current installation standard (11.5 feet minimum or...so could create an electrical hazard which could result in death or serious injury to pool users or others due to electrical shock and may cause severe damage and will create...
Model: SharkVac XL - Page 6
... the programmed cycle.
5. Dear Hayward Robotic Cleaner Owner:
Thank you a full understanding of the programmed cycle.
6. Before using your pool the entire length of the floating cable may stop in the pool, plus the depth at a minimum distance of 11.5 feet (3.5 meters) from the cleaner power supply to the wall but it...
Model: SharkVac XL - Page 7
...storage and measure out the approximate amount of cleaner cord needed for several minutes. If your pool is cleaned in the water it is released.
5. The length of the standard cleaner ... manufactured by placing the carton down . The cleaner will slowly sink to the bottom of the pool as shown. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
7 Select the nearest GFCI (Ground Fault Circuit ...
Model: SharkVac XL - Page 8
...;F (10ºC - 35ºC).
CAUTION: When removing cleaner from the shallow end of the pool by a qualified electrician according to local electrical standard (see maintenance section for less than 3 hours the...)
Store the cleaner in order to avoid a hazard.
10.
Remove the cleaner from the pool, empty the filter bucket and clean filters after each use. Should a second cleaning cycle be...
Model: SharkVac XL - Page 9
Filter Door
8. Float Assembly 12. Drive Track
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
9 Side Panel 10. Floating Cable 4. Sealed Motor Unit 13. Power Supply 2. Filter Cartridge 6. Wheel Brush and Tube 14. Filter Bucket 7. Dome Assembly 9. Handle 5. Wheel 11. 1. On/Off Switch 3.
Model: SharkVac XL - Page 13
... out of Moving Parts
WARNING: Disconnect the power supply from electrical outlet before cleaning moving parts. Inspect the venturi to
ensure free movement when changing float position. Remove any debris that no debris or hair has clogged the impeller. The impeller can be checked periodically for any cord...
Model: SharkVac XL - Page 14
... FEATURE
SharkVac-XL is the default position locating the float in the movement where the cleaner will spend more time scrubbing the pool wall along the water line or pool wall faster and benefit...
Method of the cleaner and will provide the best cleaning behavior for most swimming pools.
Float position "II" will provide an additional angle in the movement where the ...
Model: SharkVac XL - Page 16
...61623; Remove items such as elevated main drains and stair steps.
For cleaners used in the pool.
Cleaning the filter cartridges after every use maximizes the unit's performance.
Replace worn brushes...Motor Unit and the Power Supply contain no user-serviceable parts. Place cleaner away from the pool wall but do not throw the cleaner in areas that have a lot of sand the ...
Model: SharkVac XL - Page 17
...clean if necessary following the instructions in the maintenance section.
Brush roller or drive tracks may be snapped back into place, after the cleaner has run a complete cleaning cycle.
...toys. Assure that there is important to judge the performance of the cleaner by observing improved pool cleanliness after cleaning the area.
If the flotation cord gets twisted which can be ...
Model: SharkVac XL - Page 18
..., Pleated Element Cartridge Pleated Cellulose/Polyester Blend
Cleaning Routine Control Type Cleaning Cycle
Adaptive Seek Control Logic (ASCL®) Microprocessor Full Cycle 3 hours
Drive System
Direct Drive w/Polyurethane Drive Track & Acetal/Stainless Steel Bearing System
Power Supply Input Primary Voltage Output Secondary Voltage Rated Output Current Weight
110-120 VAC 24 VDC 4 A 8.3 lbs...
Model: SharkVac XL - Page 19
... REMOVE THE UNIT IMMEDIATELY FOLLOWING USE. NEVER ALLOW PLUG TO ENTER THE POOL.
8. DO NOT DRAG THE MACHINE OUT OF THE POOL AGAINST THE SIDE WALL. WARNING - USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
19... of the vacuum and inspect the electrical cord frequently for safety. ALWAYS STAY OUT OF THE POOL WHILE CLEANER IS IN OPERATION.
7. DO NOT OPERATE THE MACHINE OUT OF WATER. REPLACE DAMAGED...
Model: SharkVac XL - Page 22
... PARTS
22
AUTOMATIC SURFACE SKIMMER
Warranty Card Registration
Register online at www.hayward.com
Please Print Clearly:
Years Pool has been in a safe and convenient location for :
In Ground Above Ground
Spa
Hayward is a registered trademark of Hayward Industries, Inc. © 2011 Hayward Industries, Inc.
DETACH HERE: Fill out...
Similar Questions
Does The Non-drive Side Belt Need To Be Replaced On A Hayward, Shark Vac, Xl? An
(Posted by Willijef 1 year ago)
Replacing A Drive Belt On 1 Side Of My Sharkvac Xl
need to know how to replace belt
need to know how to replace belt
(Posted by debrass 2 years ago)
When To Replace Drive Belt On My Tiger Shark Pool Cleaner
(Posted by davso 10 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)