Home » Hayward » Pool & Spa » Hayward Power-Flo LX

Hayward Power-Flo LX Support Question

Find answers below for this question about Hayward Power-Flo LX.
Need a Hayward Power-Flo LX manual? We have 3 online manuals for this item!

Hayward Overview Questions Manuals Reviews Videos Research

Question posted by ronaldsheets on May 12th, 2013

Cord Installation

i just need to see a diagram on which color wire hooks to what pin. i needed to tape up the cord on the pump end where it goes in at because the outer coating had cracked. in doing so, two wires pulled loose from the pins. i don't know which wire goes where. do not want to burn pump up wiring wrong. it is a hayward sp1580z2. 1 h.p. 115volts 11.o amps. please help show me where they go. thanks!!!

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Hayward Power-Flo LX Manual Pages

Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 1

... be properly grounded. Turn on power and allow a reasonable time for storable pools. listed for priming. Use motor bonding lug to do not use only a properly grounded outlet. To reduce the risk of the motor. 4. All electrical wiring must be performed by a GFCI. 6. WARNING - This pump is not U.L. A permanently installed pool is constructed so that is...

Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 2

...Pump Housing Nut, No. 10-24 Hex. SPX1510-Z-1E SPX1510-Z-1XE SPX1515-Z-1E SP-1500-CP SP-1500-CP SP-1500-CP SPX1500-W SPX1500-W SPX1500-W SPX1500-RA SPX1500-RA SPX1500-RA SPX1500-LX SPX1500-LX SPX1500-LX...To order, specify motor manufacturer, HP and pump model no. special models) Strainer Shim Ring (Horizontal Outlet Pumps Only) Twist Lock Cord Set NO. NO. 1 2 3 4 5 6 7 ...

Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 3

...pump housing recess. Be sure O-ring is in handling and installing the new seal and ceramic seat assembly. Clean fiber gasket (replace if necessary) and fasten housing cover to pump housing with Twist Lock Cord... from turning. Reconnect pump to hold shaft from the pump housing. SEAL CHANGE INSTRUCTIONS Power Flo™ LX Series with eight (8) bolts and nuts. AMPS RATINGS -

Models: SP1575LXTL SP1580TL and SP1580X15TL - Page 4

... at motor (frequently caused by wear, rust, or continual overheating. C. Tighten all electric power. LOW FLOW - Motor bearings made unserviceable by undersized wiring). 3. Hayward pumps have self-lubricating motor bearings and shaft seals. Disconnect cord/electrical connections and plumbing connections. Make sure strainer cover is necessary. 3. No...

SP1575X15 - Page 1

... young children. GENERAL TIPS ON PUMP INSTALLATION STARTING AND PRIMING INSTRUCTIONS For best pump performance, locate the system below the pool water line and as close to the pool as necessary. 2. Insure that components such as the filtration system, pumps and heater be protected by applicable electrical codes. All electrical wiring must be positioned so as to...

SP1575X15 - Page 2

... SPX1500CA SPX1500W SPX1250R SPX1500P SPX1500D2 SPX1700FG SPX1500XE Motor Strainer Housing O-Ring Basket Strainer Cover O-Ring Strainer Cover Drain Plug w/Gasket Strainer Shim Ring (Horizontal Outlet Pumps Only) NO. DESCRIPTION Bolt, No. 10-24 Hex. NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 ---- Head Housing Cover Housing Gasket Impeller Seal Assembly...

SP1575X15 - Page 3

... 6. If tight, tap lightly from the pump housing. Reconnect pump to hold shaft from turning, and rotate the impeller in slot at end of non-granulated liquid-type soap. The ...pump housing with four (4) motor securing bolts. (Be sure motor base is in handling and installing the new seal and ceramic seat assembly. The spring portion of the spring seal and pull it off electrical power...

SP1575X15 - Page 4

... for blocked suction line or strainer, or air leak in open position. 2. Wiring, loose connections, etc. 2. Binding and overload. (Amperage reading) NOTE: Your Hayward pump motor is equipped with water and that pool water level is reached. Tighten all suction openings. 3. NOISY PUMP-Check for : 1. TROUBLE SHOOTING GUIDE A. The thermal overload will shut the motor...

Owners Manual - Page 1

... the potential for personal injury. ISPFSERIES Rev G PowerFlo LX™ / PowerFlo II™ / EP Pump Series Owner's Manual Contents Product Warnings 2 Installation 4 Start-Up & Operation 6 Shaft Seal Replacement...or property damage and if ignored presents a potential hazard. Hayward Pool Products 620 Division Street, Elizabeth, NJ 07207 Phone: (908) 355-7995 www.haywardnet.com...

Owners Manual - Page 2

... the flow rating as a means of the pool/spa from the suction outlets can result in evisceration/ disembowelment. Components such as the filtration system, pumps and heater must be positioned to pressure in this product. Never change filter control valve position while system pump is damaged, broken, cracked, missing, or not securely attached. To reduce...

Owners Manual - Page 3

... servicing pool and spa circulation system, filters manual air relief valve must be restored. WARNING - Also, contact a licensed electrician for use an extension cord to connect unit to a supply circuit that the circuit is not assembled properly, damaged, or missing. If the GFCI interrupts power to , grounding, bonding and other equipment. Run a continuous wire from...

Owners Manual - Page 4

... ONLY HAYWARD GENUINE REPLACEMENT PARTS 4 Self-priming PowerFlo II™ pumps may cause damage. vibration free. Pump mount must be solid - All plastic fittings must be installed below the pool water line (see Figure to plastic threads, wrap the entire threaded portion of the fitting. When applying TFE tape to right). Flexible Hose, PVC, or Reinforced...

Owners Manual - Page 5

... by code. Use green ground terminal provided under motor canopy or access place; Wiring Pump MUST be sure to seal wire opening on end of motor to local codes and regulations. Install a Ground Fault Circuit Interrupter (GFCI) in circuit; In case of a power outage, check GFCI for tripping, which will sense a short-circuit to ground and...

Owners Manual - Page 6

...pump from pump and piping system. USE ONLY HAYWARD GENUINE REPLACEMENT PARTS 6 New Installation - Start-Up & Operation Prior to pool/spa system directly in suction and outlet pipes. 3. WARNING - Running pump... 3. CAUTION - turn OFF power to suction pipe level. Storage/Winterization WARNING - CAUTION - Keep motor dry and covered during storage. Storing Pump for the mechanical shaft seal....

Owners Manual - Page 7

... the pump housing/shroud, with the eight (8) screws removed in slot at end of the motor. 8. Install strainer 'C' clip by plugging both the rotating and the stationary sections of the old seal is secure. Insert basket and fasten strainer cover. 16. Install all electrical wiring for Winterized Equipment 1. A. B. Remove the basket. Note how the steel...

Owners Manual - Page 8

...that pool water level is at full RPM's. How to determine if pump will allow the motor to automatically restart once the motor has cooled, provided the power ...Clogged or restricted strainer or suction line; Re-tighten using Teflon tape. 4. loose connections; Check voltage to check by undersized wiring or extension cord use). 3. Bypass it is felt, check for blocked suction...

Owners Manual - Page 9

....  Keep motor clean. Loose stones/debris hitting impeller could be replaced at any of chemicals causing seal damage which will sometimes prove this manual. Inspect strainer cover gasket regularly and replace as necessary.  Hayward pumps have self-lubricating motor bearings and shaft seals. DATE OF INSTALLATION INITIAL PRESSURE GAUGE READING (CLEAN...

Owners Manual - Page 10

... 17 C-Clip SPX1515C SPX1515C 18 6' Cord Set (14/3) SPX1250WA SPX1250WA 19 3' Cord Set (12/3) Twist Lock SPX1550WA1 SPX1550WA1...All Twist Lock versions for each pump have "TL" at end of model number to Part No. on 6 Impeller Original Equipment Original Equipment 7 Pump Housing SPX1500AA SPX1580AAP 8 Housing Nut...Diagram PARTS LISTING Model No. on Refer to a "2" (i.e.

Owners Manual - Page 11

...incidental or consequential damages, so the above constitutes the entire warranty of Hayward Pool Products with respect to its products to components manufactured by the respective manufacturer...(1) year from freezing, negligence, improper installation, improper use or care or any Acts of purchase is required for cartage, removal, repair or installation labor or any nature. For such products...

Owners Manual - Page 12

... Zip__________ Model Number Pool Capacity U.S. DETACH HERE: Fill out bottom portion completely and mail within 10 days of Hayward Industries, Inc. © 2015 Hayward Industries, Inc. Mail to complete warranty registration for : In Ground Above Ground Spa Hayward is a registered trademark, and PowerFlo LX, and PowerFlo II are trademarks of purchase/installation or register online...