Hayward Power-Flo Support Question
Hayward Power-Flo Support Question
Find answers below for this question about Hayward Power-Flo.Need a Hayward Power-Flo manual? We have 1 online manual for this item!
Current Answers
Answer #1: Posted by Odin on July 28th, 2018 12:47 PM
Odin
Member since:
April 10th, 2010 Points: 41,236,700
Member since:
April 10th, 2010 Points: 41,236,700
There are various Hayward products with the name Power-Flo in the title. If, for example, you have the Power-Flo LX, the instructions are at https://www.manualslib.com/manual/410399/Hayward-Power-Flo-Lx.html under STARTING AND PRIMING INSTRUCTIONS. If that's not your model [and if those instructions don't seem to apply], choose from the manuals listed at https://www.manualslib.com/h/hayward+pow- flo.html.
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Related Hayward Power-Flo Manual Pages
Model: ALL - Page 1
...
HAYWARD POOL PRODUCTS, INC.
Corporate Headquarters: 620 Division Street Elizabeth, NJ 07207
U.S.A: 1 Hayward Industrial Drive Clemmons, NC 27012
2935 Sidco Drive Nashville, TN 37204
2875 Pomona Blvd. WARNING -
C
OWNER'S MANUAL
INSTALLATION, OPERATION, & PARTS
Power-Flo LX™ / Power-Flo II™ Pump Series
The Hayward® Power-Flo LX™ and Power-Flo II™ Pump Series...
Model: ALL - Page 2
...and to all metal parts of swimming pool, spa, or hot tub, and to all times. Do NOT use , it rains. A storable pool is constructed so that will not flood... Power-Flo LX™ / Power-Flo II™ Pump Series' are intended for storage and reassembled to pool structure. Though this
product. Use a solid copper conductor, size or larger. Power-Flo LX™ / Power-Flo II™ Pump Series...
Model: ALL - Page 3
... covers. WARNING - If your supplier. Failure to bleed air from lawn mowers, hedge trimmers and other
equipment/components of the pool or spa.
Power-Flo LX™ / Power-Flo II™ Pump Series __________
____________
NOTE: The National Electrical Code (NEC) permits use the pool or
spa if a drain cover is damaged, cracked, missing, or not securely attached.
CAUTION -
Model: ALL - Page 4
...fitting an additional 1 ½ turns. The pump suction and outlet ports have molded-...Power-Flo II™ pumps may be installed up to force hose connector fitting past this stop.
Do NOT attempt to four (4) feet above the pool water line. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions
Pump Location
The Power-Flo LX™ pump MUST be installed below the pool...
Model: ALL - Page 5
...the power source. it becomes dangerous to electrical power ...Pool and spa fittings MUST conform to pool structure.
WARNING - Match supply voltage to circuit. For size of swimming pool, spa...Fault Circuit Interrupter (GFCI) in pool or double suction (skimmer and ...fatal electrical shock, turn OFF power to
motor before ...Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions...
Model: ALL - Page 6
... water. Small children using pool MUST always have close adult supervision. Power-Flo LX™ / Power-Flo II™ Pump Series
Installation Instructions (cont.)
Electrical (cont.)
Wiring (cont.)
In case of suction pipe.
NOTE: Tighten strainer cover by hand only (no wrenches) ¼ turn clockwise to Start-Up
Fill strainer housing with "Jack's 327" each time it...
Model: ALL - Page 7
...before beginning shaft seal replacement. Securely mount pump to proper water level. 6. Install all water from pump and piping when expecting freezing temperatures or when storing pump for reactivation of severe injury or death to instructions. Contact your pool/spa
system. Power-Flo LX™ / Power-Flo II™ Pump Series
Storage/Winterization
WARNING -
Follow filter manufacturer...
Model: ALL - Page 8
...Low voltage at end of seal in place onto the motor shaft. Make certain motor shaft turns freely before heat damage can contribute to seal leakage. 10. Check For:
1. If you... Check For:
1. Power-Flo LX™ / Power-Flo II™ Pump Series
Shaft Seal Change Instructions (cont.)
Exercise extreme care in handling both the skimmer outlet port and return port to pool. If assembly is ...
Model: ALL - Page 9
Centrifugal switch stuck in pump. 2. a. b. Clogged or restricted strainer or suction line; backwash as... for line blockage. Air leak in pool, and
unrestricted discharge return lines. Power-Flo LX™ / Power-Flo II™ Pump Series
Troubleshooting (cont.)
Motor Hums, But Does NOT Start - Pump Won't Prime
1. Make sure pump/strainer housing is at the strainer cover...
Model: ALL - Page 10
SP1540C
Model No. on Original Equipment
7 Pump Housing
SPX1500AA
SPX1580AAP
8 Housing Nut, No. 10-24 Hex Head SPX1500Y2 (7 Req'd.) SPX1500Y2 (8... 1780
SPX1500N2 (6 Req'd.) SPX1705B SPX1580Z1 SPX1500H SPX1500KA
Refer to Part No.
Description
Model No. Power-Flo LX™ / Power-Flo II™ Pump Series
Replacement Parts
Parts Diagram
Parts Listing
Ref.
SPX1510Z2E)
Model No.
Model: ALL - Page 11
...: Fill out bottom portion completely and mail within 90 days of the receipt of purchase. Power-Flo LX™ / Power-Flo II™ Pump Series
HAYWARD® LIMITED WARRANTY
This pump was inspected before shipment from Hayward:
□ Pump □ Filter □ Automatic Pool Cleaner □ Light □ Chlorinator □ Skimmer □ Heater Parts which fail or become...
Similar Questions
Looking For Centrifugal Switch For Hayward Power Flox 1hp Motor
(Posted by witt7229 2 years ago)
Connection Of New Pump
Does the sp1580 power flow LX pump come assembled as pictured ? It shows the outlet for the filter i...
Does the sp1580 power flow LX pump come assembled as pictured ? It shows the outlet for the filter i...
(Posted by Dk12962 9 years ago)
Where Is The Centrifugal Switch On Hayward Power Flo Lx Pump
(Posted by furktol 10 years ago)
I Have A Power Flo Xl Pump . I Replaced The Owing On The Basket Top On The Pump
I have a power flo xl pump . I replaced the o-ring on the basket top on the puman it when the pump i...
I have a power flo xl pump . I replaced the o-ring on the basket top on the puman it when the pump i...
(Posted by Reallyneatdecks64 10 years ago)