Hayward Aqua Rite Salt Chlorination Support Question
Hayward Aqua Rite Salt Chlorination Support Question
Find answers below for this question about Hayward Aqua Rite Salt Chlorination.Need a Hayward Aqua Rite Salt Chlorination manual? We have 6 online manuals for this item!
Question posted by robertckerr on May 7th, 2013
Aqua Lite Salt Chlorinator ?
red light, then green, then green then goes off and no lights ?
Current Answers
Related Hayward Aqua Rite Salt Chlorination Manual Pages
AQ-RT-PRO Oct 08 & later - Page 6
... feet/ gallons and meters/liters) if pool size is usually available in low chlorine production. This is common food quality or water softener salt and is unknown.
Use the chart on and add salt directly into the pool. A low salt level will begin to give a salty taste to your pool/spa is low, determine the number of gallons...
AQ-RT-PRO Oct 08 & later - Page 7
POUNDS and (Kg) OF SALT NEEDED FOR 3200 PPM
Current salt
Gallons and (Liters) of Pool/Spa water
level
8,000 10,000 12,000 14,000 16,000 18,000 20,000 22,000 24,000 26,000 28,000 30,000 ...
AQ-RT-PRO Oct 08 & later - Page 14
... this audible indication is NOT used. the amount of salt in the pool
The filter pump timer should only take minor, infrequent adjustments.
Display Light On for 60 sec
Toggle between Always On and On for your chlorinator cell ages. This function is pressed. For pools with temperature, most people find they have to be...
AQ-RT-PRO Oct 08 & later - Page 16
... with Local and NEC codes.
120/240 VAC POWER
AQUA
RITEpro
FROM FROM POOL SPA
TO
TO
SPA
POOL
Preparing Pool/Spa Water
Refer to page 2 for outdoor mounting. Because the enclosure also acts as a heat sink (disperses heat from the pool/spa. INSTALLATION
Installation must be balanced BEFORE activating the Aqua Rite Pro. The control must be performed in a raintight...
AQ-RT-PRO Oct 08 & later - Page 17
...:
IMPORTANT: There must be purchased separately. To ensure proper operation, verify that the Aqua Rite Pro installation does not constitute a cross connection with the local potable water supply. Plumbing...front of straight pipe.
Configurations #2 and #3 allow for chlorination of both the pool and spa during spa spillover operation, but prevent overchlorination of water flow.
14 Consult...
AQ-RT-PRO Oct 08 & later - Page 18
.... It is attached to the bottom of both the pool and spa during spillover but preventing overchlorination when operating the spa only.
For Canadian models, the Aqua Rite Pro shall be bonded with the configuration jumpers in 240VAC position. For pool/spa combination systems with spillover, use the Aqua Rite Pro as a junction box. To provide safe operation, the...
AQ-RT-PRO prior to Oct 08 - Page 6
... unknown. If the level is also acceptable to use rock salt, salt with yellow prussiate of the Aqua Rite Pro and result in low chlorine production. How to Add or Remove Salt
For new plaster pools, wait 10-14 days before adding salt to allow the salt to evaporation. Salt Level
Use the chart on page 4 to determine how much...
AQ-RT-PRO prior to Oct 08 - Page 14
... during the colder periods. The Aqua Rite Pro automatically stops generating when the pool water temperatures drops below 50ºF. This is not desired, select "Disabled".
Beeper Enabled
Toggle between Enabled (default) and Disabled Beeper Move to generate enough chlorine. Reset Config. To find the ideal setting for your pool/spa and after the last key...
AQ-RT-PRO prior to Oct 08 - Page 16
... and NEC codes.
120/240 VAC POWER
AQUA
RITEpro
FROM FROM POOL SPA
TO
TO
SPA
POOL
Preparing Pool/Spa Water
Refer to the Aqua Rite Pro system. The control is designed to the pool, per manufacturer's instructions. Because the enclosure also acts as a heat sink (disperses heat from the pool/spa. Do not mount Aqua Rite Pro inside the box), it is important...
AQ-RT-PRO prior to Oct 08 - Page 17
... the pool/spa. Electrolytic Cell: Install using the unions provided. To ensure proper operation, verify that the Aqua Rite Pro ...chlorination of both the pool and spa during spillover but prevent overchlorination of water flow. Configurations #2 and #3 allow chlorination of straight pipe.
The electrolytic cell and flow switch tee fitting are designed to the pool plumbing. For pool/spa...
AQR - Page 6
...acid), when checking salt. Use the equations below (measurements are in the pool and add salt according to the addition of water because of splashing, backwashing, or draining (because of the Aqua Rite® and result... the main drain (use water conditioning salt pellets, however, it will begin to give a salty taste to your pool/spa is to use pool vac if there is usually available in...
AQR - Page 11
... pool/spa and after that, it is activated. Adjustment of the Aqua Rite chlorinator in addition to find the ideal setting for your filter. The Aqua Rite&#...chlorine level every few days and adjust the dial up at the peak of chlorine the Aqua Rite will be lowered accordingly. Most pools require less chlorine during cold weather: Check chlorine levels periodically. The Aqua Rite salt...
AQR - Page 13
...manufacturer's instructions. The control is suitable for recommended chemical levels. FROM FROM POOL SPA
TO
TO
SPA
POOL
Preparing Pool/Spa Water
Refer to the Aqua Rite system. INSTALLATION
Installation must be balanced BEFORE activating the Aqua Rite®. Mounting the Aqua Rite Control
The Aqua Rite is contained in accordance with the knockouts facing downward. Because the enclosure...
AQR - Page 14
...: There must be plumbed into 2" (51mm) PVC pipe. For pool/spa combination systems with the local potable water supply.
If the switch is plumbed after (downstream) all the pool equipment (filter, heater, solar, etc.). Tighten unions BY HAND for information about available chlorinator cells. The Aqua Rite is after the cell, the cell can also be...
AQR - Page 18
... all 4 red/yellow LEDs are illuminated.
Salt level too low (below 50ºF) causes Aqua Rite to stop generating (Generating LED flash- Cold water (below 2400 ppm, Check Salt LED on page 4. If salt level is low, add salt according to "normal" and chlorine tests will
use chlorine at recommended levels.
6.
Possible causes of
days before the pool returns to...
Aqua Rite & Aqua Rite XL - Page 6
... a salty taste to your pool/spa is due primarily to dissolve. A high salt level can cause the Aqua Rite® to shutdown and may take longer for 24 hours with the suction coming from the main drain (use water conditioning salt pellets, however, it will most likely decline together. The salt in low chlorine production. Salt is unknown. bags...
Aqua Rite & Aqua Rite XL - Page 10
... show the pool temperature. Salt Display
The Salt Display shows the current salt concentration of chlorine the Aqua Rite will generate:
1.
If Metric units (grams per million). With the temperature displayed, move the main switch from the pool automation display/keypad. filter time each day. the "Desired Output %" setting 3.
To find the ideal setting for your pool/spa and after...
Aqua Rite & Aqua Rite XL - Page 12
... knockouts facing downward.
This ensures a quick, troublefree transfer to page 1 for outdoor mounting. Because the enclosure also acts as a heat sink (disperses heat from the pool/spa.
FROM FROM POOL SPA
TO
TO
SPA
POOL
Preparing Pool/Spa Water
Refer to the Aqua Rite system. INSTALLATION
Installation must be balanced BEFORE activating the...
Aqua Rite & Aqua Rite XL - Page 13
...pool/spa. Electrolytic Cell:
Install using the unions provided.
Adapters (not included) can be plumbed into 2" (51mm) PVC pipe. Tighten unions BY HAND for chlorination of both the pool and spa during "spa... of the cell. For pool/spa combination systems with the local potable water supply. To ensure proper operation, verify that the Aqua Rite® installation does not ...
Aqua Rite & Aqua Rite XL - Page 18
... and inspect the cell for
service.
15 If the pool has the proper amount of salt, it is too low.
- Aqua Rite® switch in pool/spa. Salt level too low (below 50ºF) causes Aqua Rite to chart on ).
- Salt level too high (High Salt LED on cell.
- Very warm pools increase chlorine demand--increase Output %, or filter run time.
- Cold water...
Similar Questions
How To Find Manufacturing Date Code On Aqua Rite Electronic Chlorine Generator
(Posted by Salvdrw1 9 years ago)
Can An Aqua Rite Salt Generator Be Controlled From A Hayward Ecostar
(Posted by krzyJON 9 years ago)
Aqua Rite Electronic Chlorine Generator Lights Stay On Generating When Turned
off
off
(Posted by 123meta 10 years ago)
How Do I Remove The Jumper In Aqua Rite Chlorinator?
(Posted by vdanGPDHut 10 years ago)
Dual Pool Spa System But The Settings Menu Doesn't Show Pool Heater Only Spa Hea
(Posted by Anonymous-39619 12 years ago)