Harbor Freight Tools 38144 Support Question
Harbor Freight Tools 38144 Support Question
Find answers below for this question about Harbor Freight Tools 38144 - 13 in. Floor Mount Drill Press.Need a Harbor Freight Tools 38144 manual? We have 1 online manual for this item!
Question posted by Anonymous-172024 on August 5th, 2022
What Size Is The Size Of The Bevel Table Lock Screw?
The person who posted this question about this Harbor Freight Tools product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by SonuKumar on August 5th, 2022 9:44 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,641,150
Member since:
May 9th, 2021 Points: 16,641,150
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Harbor Freight Tools 38144 Manual Pages
User Manual - Page 2
... should be kept safe distance from tool before turning it on.
3.
Item 38144
MAINTENANcE Indicates a hazardous situation which it was not designed. USE RIGHT TOOL. Don't force tool or attachment to do the job ...injury. REMOVE ADJUSTING KEYS AND WRENCHES. It is the safety alert symbol. Table of checking to see that follow the warnings and instructions may result in ...
User Manual - Page 3
... SECURE WORK. Use clamps or a vise to operate tool.
13. DON'T OVERREACH. Follow instructions for best and safest performance...OpERATION
MAINTENANcE
Item 38144
For technical questions, please call 1-888-866-5797. SAFETy
SETUp
General Tool Safety Warnings (cont.)
Table A: REcOMMENDED MINIMUM.... NEVER STAND ON TOOL. CHECK DAMAGED PARTS. Before further use of parts, mounting, and any other ...
User Manual - Page 4
... V~ 3-prong plug and Outlet. Item 38144
MAINTENANcE Grounding pin
125 V~ 3-prong plug... INSTRUcTIONS:
110-120 V~ Grounded Tools: Tools with an electric cord having an...Drill press Safety Warnings
For your Own Safety Read Instruction Manual Before Operating Drill press
1. Moving guards must be NIOSH-approved for drill accessory and workpiece material.
5. Do not depress the spindle lock...
User Manual - Page 5
... vibration-related injury.
3. Let the tool do this product, but must follow OSHA guidelines.
13. Page 5 Stay alert, watch what...38144
For technical questions, please call 1-888-866-5797. WARNING: Handling the cord on the tool.
15. To reduce vibration, maintain the tool as possible (while still keeping safe control of California] to the State of it).
SAFETy
SETUp
Drill press...
User Manual - Page 6
... this product.
Item 38144
Before assembly, bolt the Base to a flat, level, solid floor location capable of supporting the weight of this manual including all text under subheadings therein before drilling or driving screws. Verify that installation surface has no hidden utility lines before set up or use of the drill press and any procedure in...
User Manual - Page 7
... the end of the Spindle Shaft (13), turning, where necessary, to within 6″ of scrap wood on the arm and secure with the Set Screws.
4. With assistance, raise the Head (1A) and locate it on top of scrap wood on the table to its housing on the table, to press the chuck into position.
2. Open...
User Manual - Page 8
... (or Figure c on page 10), and install the Belts in its mounting between the motor and spindle pulleys. SETUp
OpERATION
MAINTENANcE
Page 8
For technical questions, please call 1-888-866-5797. Item 38144 SAFETy
Installing the Drive Belts
1. Undo the Belt Tension Locking Knobs (18A) on with ease.
2. Turn the Belt Tension Lever (19A...
User Manual - Page 9
... clockwise to raise and counterclockwise to the required angle. Raise or lower the table by slackening the Bevel Table Locking Screw (E), and tilting to lower.
5. For all text under subheadings therein before performing any procedure in four directions.
1. Figure B: Drill Depth Adjustment
OpERATION
MAINTENANcE
Item 38144
For technical questions, please call 1-888-866-5797. Page 9
User Manual - Page 10
...950
1600
1900
2000
2500
2900
3600
M24 Left Belt
Figure c: Drill Speed Table
The table above shows the belt arrangements for given drill speeds (A full chart is also located on the inside the pulley... reasonable thumb pressure.
Bit Installation
M25 Right Belt
1. Item 38144
Slacken off the Belt Tension Lock Knobs (18A) on the pulley's according to the spindle which corresponds to firmly ...
User Manual - Page 11
... Cord into the workpiece.
or align the table so that the drill will result not only in its power supply after use a drill press vise. If the drill bit grabs and spins the workpiece, do not attempt to be drilled.
10. To prevent accidents, turn the drill press off the tool and disconnect its center is sufficient for the...
User Manual - Page 12
...Drill Speed on page 10. SAFETy
Maintenance and Servicing
procedures not specifically explained in this manual must be performed only by a qualified service technician.
WARNING!
TO pREVENT SERIOUS INJURy FROM AccIDENTAL OpERATION: Turn the power Switch of the tool off and unplug the tool... power tool is damaged, it must be replaced only by a qualified technician.
Item 38144 If ...
User Manual - Page 13
... outlet. Press reset button on page 3. Tool operates slowly.
4. Internal damage or wear. (Carbon
brushes or bearings, for example.)
Extension cord too long or wire size too small...shown for its length and load.
Carbon brushes worn or damaged. 1. Item 38144
For technical questions, please call 1-888-866-5797. Eliminate use one with ...See Table A on page 3. 1.
Page 13
User Manual - Page 14
...parts List and Diagram
Part # 1a 1b 2 3 4 5 6 7 8 9 10 11 12 13
Description "V" Belt M24 "V" Belt M25 Pulley Nut Spindle Pulley Pulley Insert Ball Bearing Spacer Retaining Ring ...Arbor Chuck Chuck Key Wedge Drift Ball Bearing Idler Pulley Idler Pivot Knot Pan Head Screw Pulley Cover Washer HD Screw Foam Washer Chuck Guard
1a
Code 1503007 1503009A 1503010A 1503008 60202 1505006-02 1705007 1505008...
User Manual - Page 15
...OpERATION
MAINTENANcE
REV 12f
Item 38144
For technical questions, please call 1-888-866-5797.
Nut Washer Motor Cable Hex Screw Belt Tension Lock Knob Belt Tension Lever Roll Pin Head Lock Set Screw Depth Lock Screw Knob
Code 1302001A 1502014A ... trim Cable Clamp Pan Head Screw Bolt Adjusting Lever Motor Support Bracket Motor Support Bracket Motor Mount Lock Washer Nut Motor Pulley Skt.
User Manual - Page 16
...Screw Set M6 Bevel Table Lock Screw Table Clamp Arm w/ scale Table Arm Locking Handle Helical Gear Worm Collar Belt Tension Lever
Code 1301003 1301010 M10x12 1301002 M10x40 1301001 1501004 1001009 1501007 M6x10 M16x35 1501013 1301005 1601014 1501012 1501006 1501008 1501011 1502004
Limited 90 Day Warranty
Harbor Freight Tools...accompany the merchandise. Base and Table
Note: All part numbers shown ...
Similar Questions
Connecting Bar Screw Size
can I pick up screw at a hardware store, what is the proper thread size and proper length
can I pick up screw at a hardware store, what is the proper thread size and proper length
(Posted by jdias4146 2 years ago)
Do You Sell The Key Chuck For The Central Machinery 61484?
I need to purchase a drill chuck for my Central Machinery #61484.Do you sell them?
I need to purchase a drill chuck for my Central Machinery #61484.Do you sell them?
(Posted by kbback 2 years ago)
Need Replacement Parts For 16 Speed Floor Drill Press Model 43389
need Item 15 Locking Switch 02A0549Item 18 Switch KeyItem 19 Switch Plate CoverSonney 760-300-5377
need Item 15 Locking Switch 02A0549Item 18 Switch KeyItem 19 Switch Plate CoverSonney 760-300-5377
(Posted by hp25years 5 years ago)
What Is The Size Of The Pulley Nut?.
There is a nut that holds the pulley to the spindle, listed in the manual as 1302025. I have tried m...
There is a nut that holds the pulley to the spindle, listed in the manual as 1302025. I have tried m...
(Posted by douglasklinkerman1 6 years ago)
What Size Bushing To Replace On Inside Of Wheel?
What is the replacement size of the bushing needed on the wheel 15.5" X 4" for the 20 ton HF log spl...
What is the replacement size of the bushing needed on the wheel 15.5" X 4" for the 20 ton HF log spl...
(Posted by larryshultz 9 years ago)