Hamilton Beach HMD400 Support Question
Hamilton Beach HMD400 Support Question
Find answers below for this question about Hamilton Beach HMD400 - Commercial Drink Mixer.Need a Hamilton Beach HMD400 manual? We have 1 online manual for this item!
Question posted by dates on October 21st, 2012
Problem With One Of The Spinners On My 400 Hmd Shake Mixer.
Could this be that we need a new motor head or a switch? When you spinning the spindle with your hand. It start working again.
Current Answers
Related Hamilton Beach HMD400 Manual Pages
User Guide - Page 2
...8226; Inspect mixer and agitator daily.
• Replace agitators every 90 days.
• Do not operate any manner.
- When using Mixer. •...installing or removing agitator. • Do not spray or submerge mixer. • Always use metal container when mixing.
•...is damaged in this manual and on your appliance. Mixer Safety
IMPORTANT SAFETY INSTRUCTIONS
Your safety and the safety...
User Guide - Page 3
... parts and features before using the mixer.
3-Speed selector switch
Top view of controls
Pulse switch
Top view of your mixer are shown on this page. Parts and Features
The parts and features of controls
Pulse switch
3-Speed selector switch
Pulse switch
Container guide Mixing spindle Agitator Container rest
Housing plug
Pulse switch Top cover
Housing
Container guide
Mixing...
User Guide - Page 4
... lift the container up off the motor, rest a standard container on . Plug mixer into the container. NOTE: Inspect... 90 days.
Operating the Mixer
Mixing a Drink
wWARNING
Cut Hazard Always use . When the drink is used when mixing with...mixer. Set the container down from the container guide.
Mixing a Drink
You must read the "Mixer Safety" section before using the 3-speed selector switch...
User Guide - Page 5
...clockwise into the spindle and hand tighten.
Plug Mixer into the container guide holes after removing the container guide. Unplug mixer.
2. Hold ...to operate the mixer when using the mixer without the container guide and container guide pin. Use the toggle switch to note the...parts. To replace the Agitator:
1. To install the new agitator, turn the screw portion of the container guide.
...
User Guide - Page 6
... repeat mix for 5 seconds. NOTE: Inspect agitators daily.
Fill the container with sanitizing solution (1 tablespoon of household bleach per 1 gallon of the Mixer
Cleaning and Sanitizing the Container, Spindle, and Agitator
Cleaning
1. Empty sanitizing solution and rinse container.
3. DO NOT RINSE after sanitizing is completed. Failure to do so can result in...
User Guide - Page 7
...with the front screw boss in the housing. Friday www.commercial.hamiltonbeach.com
To replace the motor, follow the same procedure for illustration purposes. Loosen the...into the housing, guiding the spindle through the hole in the housing.
6. Care and Cleaning of the Mixer
Motor Replacement
Single Spindle Drink Mixer shown for Triple Spindle Drink Mixer. Replace all parts before ...
User Guide - Page 8
...year from defects in your hand or allowing agitator to hit ..., or province to province.
Commercial Technical Service 261 Yadkin Road ... is not tall enough to activate motor switch. Turn unit OFF.
Product Warranty
...agitator fastened tightly to the spindle? • Is agitator...Drink".
Hamilton Beach/Proctor-Silex, Inc. Care and Cleaning of the Mixer
Troubleshooting Guide
PROBLEM...
User Guide - Page 24
840145000 5/06
261 Yadkin Road Southern Pines, NC 28387
www.commercial.hamiltonbeach.com
Similar Questions
Parts For Hamilton Beach Hand Mixer Model 62637
Can i purchase dough hooks for hamilton beach hand mixer model 62637?
Can i purchase dough hooks for hamilton beach hand mixer model 62637?
(Posted by lisayoung3355 5 months ago)
Need Model Numbers Associated With Hamilton Beach 62670 Hand Mixer Flat Beaters
Looking for model or part numbers associated with flat beaters that will work with the Hamilton Beac...
Looking for model or part numbers associated with flat beaters that will work with the Hamilton Beac...
(Posted by ramailbox 2 years ago)
Disassemble 63100 Stand Mixer
I am trying to disassemble my stand mixer but there seems to be a screw at the back of the mixer tha...
I am trying to disassemble my stand mixer but there seems to be a screw at the back of the mixer tha...
(Posted by Claremont 3 years ago)
Please, Can U Give Me A Information About The Voltage Of This Model. Is It 120v
(Posted by manigela 9 years ago)
I Need Beater For Type M18 Model 62681 Hand Mixer; Give Cost & Supplier.
(Posted by sfowjs 12 years ago)