Hamilton Beach HBH650 Support Question
Hamilton Beach HBH650 Support Question
Find answers below for this question about Hamilton Beach HBH650 - Bar Blender - Tempest 64oz.Need a Hamilton Beach HBH650 manual? We have 1 online manual for this item!
Question posted by tpantalo on October 26th, 2011
Leaking Oil From Top Of Base Drips From Bottom Of Jug When You Lift Jug From Bas
The person who posted this question about this Hamilton Beach product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Hamilton Beach HBH650 Manual Pages
Operation Manual - Page 2
... an appliance containing hot oil or other liquid.
9. If cutter assembly blades are sharp. Inspect container and cutter assembly daily. Hot liquids may cause injuries.
14. Always operate blender with container lid in place.
27. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Plug into blender container while operating blender.
15. Do not spray the base with all equipment...
Operation Manual - Page 3
Electrical Shock Hazard Disconnect power before cleaning blender base. Do not remove ground. Failure to follow these instructions can result...moisture from the cutter assembly. 5. Electrical Shock Hazard Plug into a grounded outlet. Empty container. 2. Place empty container on base and run on LOW speed for 2 minutes. 4. Do not use caution when blending hot contents. Do not use , ...
Operation Manual - Page 4
Your Tempest blender is designed for the Tempest blender are shown on this page. Max
Stop
High Speed Low Speed Jump Cycle ... (O)
Pulse Removable Filler Cap
Lid
64 oz.
Become familiar with all parts and features before using your blender. Polycarbonate Container
Blender Base
Reset Switch/ Circuit Breaker
Control Panel
Timer Knob*
*
= 3 Min. Parts and Features
The parts and features ...
Operation Manual - Page 5
... container on a dry, level surface.
3. Press the Power ON (I)/OFF (O) button to desired run time.
7. Adjust the timer knob to turn the blender ON (I ).
6. Place the blender on the base with ingredients and container lid in place.
5. Read Important Safety Instructions and Warnings before use.
2. Make sure the power switch is ON (I ). NOTE...
Operation Manual - Page 10
Thermal Overload Protection
1
2
3
4
5
6
00:00 Remove jar within
:03
10
00:02:00
Blender will automatically turn off after 2 minutes of low-speed "cool down cycle".
Operation Manual - Page 12
...is seated properly on the bottom of the cutter by rotating the drive end of the blender base.
Attempt to run "cool down cycle" or allow unit to see if unit is ... blown or if a circuit breaker
has tripped. • Check the integrated circuit breaker on the blender base. See "Thermal Overload Protection" for details.
12 See "Replacing the Cutter Assembly" for additional details...
Operation Manual - Page 13
...that minimal on-site maintenance cannot be performed, Hamilton Beach Commercial will be prorated based on the time period remaining on implied warranties or special, incidental or consequential damages... ALL CLAIMS FOR SPECIAL, INCIDENTAL AND CONSEQUENTIAL DAMAGES ARE HEREBY EXCLUDED. We will be based upon the date of the warranty will ship a replacement product to wear, including without...
Similar Questions
Blade Shaft Leaking
My 54615 blender blade shaft is leaking. Can I get the soft o rings or is there a way to fix or repl...
My 54615 blender blade shaft is leaking. Can I get the soft o rings or is there a way to fix or repl...
(Posted by Smarcus531999 2 years ago)
It Leaks
when u mix in the blender it leaks out of the wholes,is there something missing from tbere,
when u mix in the blender it leaks out of the wholes,is there something missing from tbere,
(Posted by gwen334 6 years ago)
My 'new' 3 Speed Blender M Leaks. There Is. Small Opening On The Side That Need
my new Hamilton Beach blender, Model 58142R leaks from the side. there is a small opening that needs...
my new Hamilton Beach blender, Model 58142R leaks from the side. there is a small opening that needs...
(Posted by Luanturner 9 years ago)
Leak At Bottom Of Glass.
is there a seal that can be replaced from base of glass.
is there a seal that can be replaced from base of glass.
(Posted by oliverwiliams 11 years ago)
Blades Not Making Contact With Base
Our blender's blades have stopped rotating due to lack of contact with the base / motor. The top con...
Our blender's blades have stopped rotating due to lack of contact with the base / motor. The top con...
(Posted by tleboeuf1 11 years ago)