Hamilton Beach 908 Support Question
Hamilton Beach 908 Support Question
Find answers below for this question about Hamilton Beach 908 - 908 Commercial Bar Blender.Need a Hamilton Beach 908 manual? We have 1 online manual for this item!
Question posted by lordjim999 on July 24th, 2014
Clutch Removal
How do I remove the clutch piece. It on screws with left hand threads, but how do I keep the shaft from turning?
Current Answers
Related Hamilton Beach 908 Manual Pages
Operation Manual - Page 2
...blender. Failure to know the complete model number. We have provided many important safety messages in jar when blending. Do not remove...WARNING." Blender Safety
IMPORTANT: This operation manual should be preceded by calling your nearest Hamilton Beach Commercial Service ...Do not put hands, spoons, or other utensils in this manual. EST Friday
(www.commercial.hamiltonbeach.com)
2...
Operation Manual - Page 3
...For a complete operation manual in the "off" or O position. Replace jar and cutter assembly at www.commercial.hamiltonbeach.com or call 910-692-2223.
- If fitted with a high-pressure spray gun.
• Disconnect...a dry, level surface.
2. If blending action stops during operation, turn blender OFF, remove jar from outlet when not in use .
• Avoid contacting moving an appliance containing ...
Operation Manual - Page 4
... designed to make daiquiris or similar drinks. Note: The Blender is designed for the 901/908/909/910/918/919 Blenders are shown on this page.
Removable Filler Cap
Cover
Cutter Unit Assembly Gasket
Blades
Container
Models 908/909 On/Off Switch
HIGH/LOW Switch
Clutch
Blender Base
Model 901 On/Off Switch
Models 910/918/919...
Operation Manual - Page 5
... cord. Release the Pulse switch to "Cleaning the Blender." Refer to stop . Screw the completed blade assembly onto the container. ON/OFF/ Pulse
5. Do not remove ground. Failure to run at approximately 18,000 RPM, or OFF. Do not put hands, spoons or other utensils in the threaded collar, blades up. Slip the gasket OVER...
Operation Manual - Page 6
...blender from container cover before blending. Failure to follow these instructions can be observed: • Do not exceed 1 quart of content when blending
hot product.
Pour the liquid into the container FIRST.
• Cut solid ingredients into pieces... mixtures in liquid, then add ice. For blending hot liquids, remove filler cap from processing the product properly.
Small ice cubes or ...
Operation Manual - Page 7
...in death, fire, or electrical shock. Repeat step 3 using commercially available test strips and should consist of 1 tablespoon of household ... remaining moisture from the base, and then remove the cover. Do not put hands, spoons or other utensils in water or other...cap and run the blender on base.
3. Immerse the cover and filler cap in broken bones or cuts.
Remove the container from ...
Operation Manual - Page 8
... remove the container from the base, and then inspect the container and cutter unit assembly for the Blender
Troubleshooting Guide
Problem . . .
Unplug the blender, and then inspect the power cord insulation and power plug for repair or replacement.
Replace the container and cutter unit assembly at all times.
• Solid pieces are too large. Pieces...
Operation Manual - Page 9
...from abuse, misuse, neglect, unauthorized repair, or use this product: (motor brushes, container and cutter assembly, clutches, bristle brushes, funnel, stainless steel cup, agitators, carafes, etc.). Always use not in conformity with this product... damages, so the foregoing limitations may be presented; Commercial Customer Service
263 Yadkin Road
Southern Pines, NC 28387
5/03
9
Similar Questions
How To Remove Blades To Clean The Stem
How to remove blades from blade assembly to clean shaft
How to remove blades from blade assembly to clean shaft
(Posted by lhgordon 5 years ago)
Hamilton Beach Blender Replacement Blade
Can I get a replacement blade for my Hamilton Beach blender model #52300 Type B36?
Can I get a replacement blade for my Hamilton Beach blender model #52300 Type B36?
(Posted by spiritwolf78 11 years ago)
My Blender Is Leaking, How Can I Fix It Or Tighten It?
(Posted by pmichaelj 12 years ago)
Reset Button On A 990 Commercial Blender
Is there a reset over load button on a 990 commercial blender? if so where is it and how do you ...
Is there a reset over load button on a 990 commercial blender? if so where is it and how do you ...
(Posted by josephgariepy 12 years ago)