Haier RDE350AW Support Question
Haier RDE350AW Support Question
Find answers below for this question about Haier RDE350AW - 6.5 Cu. Ft. Electric Dryer.Need a Haier RDE350AW manual? We have 1 online manual for this item!
Question posted by Donald3329 on January 12th, 2019
How To Replace Heating Elements I Can’t Find It
The person who posted this question about this Haier product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Answer #1: Posted by Fabulouslady on January 12th, 2019 9:03 PM
Fabulouslady
Member since:
December 15th, 2013 Points: 1,840
Member since:
December 15th, 2013 Points: 1,840
Turn off the power to the water heater at the breaker. Open the cover on the side of the tank. Disconnect the two wires on the element. Note: Make sure the water is drained below the element being replaced. Use an element puller to remove the bad element. Insert a screwdriver into the element puller to get more leverage. Remove the element Install the New ElementInsert a new element and tighten. Fill the tank with water above the new element. If there aren't any leaks, reconnect the wires. Replace the cover.
Related Haier RDE350AW Manual Pages
User Manual - Page 2
... INSTRUCTIONS 5-17 Tools and Materials Required 5 Electrical Requirements 5 Unpacking Your Dryer 6 Exhaust System Requirements 7 Gas Supply Requirements 9 Location of Your Dryer 10 Manufactured (Mobile) Home Instruction 11 Electrical Installation 12 3-Wire Cord Connections 13 4-Wire Cord Connections 14 Gas Connections 15 Replacement Parts 17 OPERATING INSTRUCTIONS 18-24 Understanding...
User Manual - Page 3
..., beauty salons, etc.
English
IMPORTANT SAFETY INSTRUCTIONS
Before beginning installation, carefully read these instructions. NOTE: The electrical service to the dryer must not be followed to minimize the risk of fire or explosion or to light any electrical switch. If you cannot reach your building. 3. Clear the room, building, or area of the...
User Manual - Page 4
...eliminate static unless recommended by the manufacturers of fire, electric shock, or injury to carry out.
9. Do ...static unless recommended by the manufacturers of the dryer.
14. Don't dry articles that have ... with controls.
8. Do not repair or replace any part of the appliance or attempt any...could ignite or explode.
3. Do not use heat to dry articles or products to the weather.
...
User Manual - Page 5
... liquids or solids, it to record the model and serial number. Always disconnect dryer from electrical supply before it is properly grounded.
19. Disconnect power cord by grasping the plug, ...This easy-to whether the dryer is used in back of flammable liquids and its intended purpose: drying clothes.
20. Model number Serial number Date of child entrapment. Replace worn power cord and/...
User Manual - Page 6
...SAVE THESE INSTRUCTIONS
Tools and materials required
• Phillips-Head and flathead screwdrivers • Channel-lock adjustable pilers • 1/2-inch open end
5 ELECTRICAL REQUIREMENTS
Electric Dryer: (RDE350AW)
Circuit Individual 30 Amp branch circuit fused with flexible plastic venting materials. All old gas connectors and gas piping should be easily crushed,and ...
User Manual - Page 7
... ends or closed loop connectors and marked for use with a three-prong grounding plug for use with clothes dryers.
This includes the foam base and all packaging material. NEMA 14-30R receptacle)
ELECTRICAL REQUIREMENTS Gas Dryer: (RDG350AW)
Circuit Individual 15 Amp branch circuit fused with a 120 Volt 3-wire power supply cord. Do not...
User Manual - Page 8
...a rigid or flexible metal duct. If your dryer. The dryer must be expelled into the interior of plastic duct or metal foil duct, replace it must not be exhausted into any gas vent, chimney... which extend into the laundry area. Explosion hazard: Do not install the dryer where gasoline or other fastening devices which has a swing-out damper hat open when the dryer is made up inside ...
User Manual - Page 9
... 0 1 2 3
Rigid Metal
90 ft. 60 ft. 45 ft. 35 ft. The more often you should be 102 mm in vent restriction.
5. Rigid Metal
60 ft. 45 ft. 35 ft. 25 ft.
In Canada, that only those foil-...
No. The vent flap should be used the more the dryer is acceptable. The total length of the dryer:
1. Certain extenuating circumstances could affect the performance of flexible ...
User Manual - Page 10
...pressure testing of 1/2 psig (3.45kPa). 7. The dryer MUST be installed in Canada, the current CAN/CGA B149.1
2. English
GAS SUPPLY REQUIREMENTS
WARNING Replace copper connecting pipe that is not plasticcoated. The ... have an individual manual shutoff valve installed within 6 feet (183cm) of the dryer in excess of the gas supply piping system at test pressures in accordance with the B149.1,...
User Manual - Page 11
...area exposed to ensure the installation provides the minimum amount of clearance required for the length of the dryer. A louvered door with a door, a minimum of 120 square inches (774.2 square cm)...Installation in a bedroom, bathroom, alcove or closet MUST be exhausted outdoors. 3. DO NOT install your dryer in contact with a solid door. 2. In an area where it will come in a closet with...
User Manual - Page 12
... exhaust system MUST terminate outside make up air. Refer to be fastened to the mobile home structure.
3. This dryer MUST be not less than twice the area of the dryer exhaust outlet.
4. When installing a gas dryer into a manufactured home, a provision must be made for other important venting requirements. 6. Metal ducting must be 4 inch...
User Manual - Page 13
... purchased, allowing some slack in the cord. This appliance must be grounded. Check with a copper-wired receptacle. ELECTRIC Dryer (RDE350AW) GROUNDING INSTRUCTIONS
This appliance must be cut or remove the grounding prong from this manual for electric current. If the strain relief is properly installed and grounded in accordance with the circuit conductors and...
User Manual - Page 14
... on the back of the dryer with two screws. Power cord, NEMA 10-30 Type SRDT, through the strain relief.
4. Install a U.L. Tighten both screws securely. Green Ground Screw
Brass Terminal
Neutral Ground Wire
Terminal Block
Nut
Tighten Nut to the back of the dryer's upper corner.
2. English
ELECTRICAL CONNECTIONS
ELECTRIC Dryer (RDE350AW)
3-Wire Cord Connection (US...
User Manual - Page 15
English
ELECTRIC Dryer (RDE350AW)
4-Wire Cord Connections (US Models Only)
Green Ground Screw
Green Power Cord Ground Wire
Brass ...Finger tighten the nut only at this time.
3. Install a UL approved strain relief into the power cord entry hole of the dryer upper corner.
2. Typical Conductor Receptacle
Typical 4 Conductor Cord
Black 240V White Neutral Red 240V
Green Ground
14 Remove the green ...
User Manual - Page 16
...power cord.
9. Connect a 1/2 inch (1.27cm) I.D. Test all four legs. With the dryer in the gas supply line.
4. THE DRYER MUST BE LEVEL AND RESTING SOLID ON ALL FOUR LEGS.
7. Also see that nothing (such...64258;ammable vapors. Apply an approved thread sealer that the strain relief does not turn the dryer to light. Connect the exhaust duct to the cabinet with kit. 15 NOTE: check to ...
User Manual - Page 18
WARNING
The instructions in this dryer can become an airtight chamber and cause suffocation leading to ...a certified electrician to disconnection when servicing controls. Make all wires prior to install and wire the dryer.
17 English
REPLACEMENT PARTS
Replacement parts and accessories for proper operation after servicing. Wiring errors can be purchased through Haier America at ...
User Manual - Page 25
...VTFIBSTIPSBCSBTJWF cleaners, as this could damage the dryer. After cleaning, slide the filter back in the room, electric voltage, length of the
dryer door.
Tips
t'PSCFTUESZJOHSFTVMUT DMFBOUIFMJOU... unit to dry on many variables: load size, type of fabric and
moisture in it, heat and moisture in place. Remove any residue before drying next load.
The filter may be removed...
User Manual - Page 26
...PWFSESZJOH"EKVTUGPSTIPSUFSESZJOHUJNF t.JYFEXJUITZOUIFUJDTGBCSJD4PSUBOETFQBSBUFEJGGFSFOUGBCSJD t6TFBGBCSJDTPGUFOFS
25 Dryer makes noise when drying: t$IFDLGPSDPJOT MPPTFDIBOHF CVUUPOTBOEPUIFSIFBWZPCKFDUTUIBUDPVMECF
causing the noise.... t*GUIFDMPUIFTESJFTVOFWFOMZBIJHIFSESZTFUUJOHNBZCFSFRVJSFE PSDMPUIFT
in the dryer need to be replaced.
User Manual - Page 27
... united States. Labor, service transportation, and shipping charges for the cost of the part. Haier will repair or replace any product modification, alteration or adjustment not authorized by a Haier authorized service center. Second through Fifth Year. For...flood, or acts of original purchase NO OTHER WARRANTY APPLIES. Damage from incorrect electrical current, voltage or supply.
User Manual - Page 52
...FTUPVWFSUF
La sécheuse fonctionne mais ne sèche pas : t-FUBNCPVSFTUQFVUÐUSFUSPQQMFJO/FQBTSFNQMJSQMVTRVËNPJUJÏ t-FTUVZBVYEÏDIBQQFNFOUFUMFTDMBQFUTOFEPJWFOUQBTÐUSFPCTUSVÏT t-FUVZBVEÏDIBQQFNFOUEPJUÐUSFOFUUPZÏSÏHVMJÒSFNFOU...
Similar Questions
Haier Hlp140e Leaking Water After I Changed The Heating Element.
Hi there,So I just changed my heating element on my Haier HLP140E since the original one died recent...
Hi there,So I just changed my heating element on my Haier HLP140E since the original one died recent...
(Posted by simonbussiere 2 years ago)
Heating Element On Haier Dryer 2.6 Cu.ft
My dryer does not blow warm enough. When I put it at the higher setting it does not blow any hotterD...
My dryer does not blow warm enough. When I put it at the higher setting it does not blow any hotterD...
(Posted by mkgil 3 years ago)
How Do I Get Inside Of My Haier Dryer To Replace The Element Model #rde350aw
How do I get inside of my Haier dryer to replace the element.
How do I get inside of my Haier dryer to replace the element.
(Posted by emmajackson476 10 years ago)
How To Replace A Haier Dryer Heating Element
(Posted by aithaSpo 10 years ago)
Heating Element
where is the heating element located in the HAIER RDE350AW electricv Dryer
where is the heating element located in the HAIER RDE350AW electricv Dryer
(Posted by MoniqueThomas1 11 years ago)