1999 Ford F250 Support Question
1999 Ford F250 Support Question
Find answers below for this question about 1999 Ford F250.Need a 1999 Ford F250 manual? We have 1 online manual for this item!
Question posted by acfallwell on December 7th, 2012
Stalling Out
99 v10 stalls out when i push the clutch in to stop
Current Answers
Related Manual Pages
Owner's Manual - Page 7
Instrumentation
Gearshift lever (pg. 116)
Electronic sound system (pg. 29)
VOL - PUSH ON
AM FM BASS TREB
FM1
ST
BAL
FADE AUTO SET
SEEK
VE RDRI OVE
REW
TUNE
SCAN
EJ
w
DISCS
TAPE CD
FF
1
4X4 4X4 ...
Owner's Manual - Page 15
... within the normal area (the area between the "H" and "C"). If the coolant is not at its proper level the gauge indication will not be accurate. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Owner's Manual - Page 17
... control to Engine oil in the normal range (the area between metric and English units. The appearance of status. If the gauge indicates low pressure, stop the vehicle as soon as the needle remains H in the Maintenance and care chapter). Sufficient pressure exists as long as safely L possible and switch off...
Owner's Manual - Page 22
To activate: • the ignition must be in the ON position and • the headlamp control is in a collision. High beams Push forward to turn on your headlamps under these conditions.
The Daytime Running Light (DRL) System does not activate your tail lamps and generally may result ...
Owner's Manual - Page 26
... modes except (Panel) and (Floor). Mode selector control Controls the direction of the instrument panel, as these objects may become projectiles in a collision or a sudden stop. OFF
A/C
MAX A/C
The air conditioning compressor will only function if the outside air inlet duct.
Controls and features
Do not place objects on the ground...
Owner's Manual - Page 28
... OFF position. • Don't put objects under the hood).
• If your vehicle has been parked with the climate control system in a collision or sudden stop.
28 This will reduce your climate control system. Then operate your instrument panel. These objects can fall down into the defroster outlets and block airflow...
Owner's Manual - Page 41
... switch is turned back on by using the volume/power control.
AM/FM select in radio mode This control allows you to stop tape play and begin radio play . VOL - PUSH ON
If the volume is set above a certain level and the ignition is turned off by pressing the AM/FM select...
Owner's Manual - Page 83
... is relatched into place. • Pull the seatback handle up to recline the seat. • Push the release lever down to raise or lower the front portion of the seat cushion.
83 Do not... chair (if equipped) • Lift the release bar to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright and the lap belt snug and low across the hips. ...
Owner's Manual - Page 108
... brake is set .
• If • •
Make sure the gearshift is set . Turn the key to 4 (ON) without turning the key to the floor.
3. Push the clutch pedal to 5 (START).
4 3 5 2 1
108 If starting a vehicle with an automatic transmission: • Make sure the parking brake is in P (Park). Make sure the headlamps...
Owner's Manual - Page 121
Use 2H or 4H for 4WD equipped vehicles. Disengage the clutch, apply brake and shift into N (Neutral).
1 2
3 4
D R
R 1 3 D L 2 4
121 Downshift at a stop. Driving
Maximum downshift speeds 1 6-speed transmission Shift from: Transfer case position (if equipped)2 2H or 4H 4L D (Overdrive) - 4 72 km/h (45 mph) 26 km/h (16 ...
Owner's Manual - Page 124
... a special transmission case, internal components and calibration for recommended electrical installation.
124 Driving
Removing key from ignition • Turn the ignition key until it stops. • Push the release lever forward and rotate the key towards you and remove.
Refer to the 7.3L Diesel Supplement for information on the auxiliary powertrain control...
Owner's Manual - Page 127
...high) to 2H (2WD high) Move the transfer case lever to 2H 2H (2WD High) at complete stop, disengage the locking hubs 4L (optional) by rotating the hub lock control from FREE to LOCK, then ... hubs by rotating the hub lock control from LOCK to FREE. N With the vehicle at a stop . 2. Bring the vehicle to a complete stop or any forward speed up to 4L (4WD low) 1. Place the gearshift lever in N (...
Owner's Manual - Page 129
... HIGH position at 4X4 any shift concerns to your front hubs. Bring the vehicle to a complete stop. 2. Depress the brake. 3. LOW 2WD • Do not shift into 4x4 HIGH with the...not need 4X4 HIGH LOW 2WD to put the gearshift in N (Neutral) (automatic transmission) or depress the clutch (manual transmission).
129
Shifting between 4x4 HIGH (4WD high) and 4x4 LOW (4WD low) 1. Place ...
Owner's Manual - Page 131
... may be improved by moving your vehicle speed may stall. Once through water, determine the depth; Wet brakes do not stop the vehicle as effectively as dry brakes. avoid water...considerably, especially if you are submerged in a lower gear rather than the bottom of stalling. Driving
Sand When driving over the crest. Apply the accelerator slowly and avoid spinning the...
Owner's Manual - Page 134
...fall below the maximum shown under maximum trailer weight on the brake pedal. 134 Water may stall. Once through standing water, especially if the depth is higher than the Total Axle Reserve ...by moving your vehicle slowly while applying light pressure on the chart. Wet brakes do not stop the vehicle as effectively as you limit your vehicle can carry/tow 1. If driving through ...
Owner's Manual - Page 154
...the spare tire: • With tapered end of the jack handle into the rear bumper opening. Push against the tire to make sure it is raised to the stowed position. Lay the tire on the...up the eyebolt with the valve stem facing up. 2. Turn the jack handle clockwise until you will stop moving and you can slide the tire rearward and the cable is raised to its original position underneath...
Owner's Manual - Page 165
... gases that the cables are clear of fan blades, belts and other moving parts of an exposed metal part (to the negative (-) terminal of the stalled vehicle's engine, away from the battery and the carburetor/fuel injection system. A spark may cause an explosion of the assisting battery.
4. Roadside emergencies...
Owner's Manual - Page 204
.... 6. Make sure that the headlamp control is removed for an extended period of the plastic base until you feel a "stop." 8. Connect the electrical connector into the socket by its plastic base and do not touch the glass. Install bulb retaining ... from your hand could cause the bulb to break the next time the headlamps are aligned, push the bulb into the headlamp assembly.
Owner's Manual - Page 207
...assembly. 3. Install the bulb socket in lamp assembly by turning it from the socket and push in the new bulb. 4. see your dealer (a) Replace entire lamp assembly; Replacing license ...Headlamps (aerodynamic) 2 9007 Headlamps (sealed beam) 2 H6054 Park/turn 2 3157 Sidemarker 2 194 Tail/stop/turn and carefully pull to locate the bulb. 2. bulb is not serviceable. To change the license plate...
Owner's Manual - Page 234
... properly installed. EST, for credit card holders only To order the publications in this portfolio in the United States: Make checks payable to stumble or stall. Service Publications P.O. In addition, such systems may be damaged or their performance may be installed only by operating your vehicle. (Citizens band [CB] transceivers, garage...
Similar Questions
I Installed A Neutral Safety Switch In Our 99 F550 And It Still Wont Start..sugg
(Posted by verngrogreen 9 years ago)
I Have A To Prime And Bleed My Clutch Ever Time I Get And
I have a 1989 ford f250 and I have to prime and bleed my clutch just about ever time I get in?
I have a 1989 ford f250 and I have to prime and bleed my clutch just about ever time I get in?
(Posted by Jmf0622 11 years ago)
Ford F250 V10 Hub Bearing
How hard is it to change the hub bearing on a 2000 F250 v10 ford truck?
How hard is it to change the hub bearing on a 2000 F250 v10 ford truck?
(Posted by valkoff62 11 years ago)