Home » Fisher and Paykel » Refrigerators » Fisher and Paykel RF135BDRUX1

Fisher and Paykel RF135BDRUX1 Support Question

Find answers below for this question about Fisher and Paykel RF135BDRUX1.
Need a Fisher and Paykel RF135BDRUX1 manual? We have 2 online manuals for this item!

Fisher and Paykel Overview Questions Manuals Reviews Videos Research

Question posted by ranyake on April 13th, 2013

Ice Maker

I recently removed the ice tray to clean it. After placing it back in its place i notice the ice maker no longer dispenses ice, is there something I'm doing wrong?

I Know the Answer!

I have the same question
Request More Information

Current Answers

There are currently no answers that have been posted for this question.
Be the first to post an answer!

Remember that you can earn up to 1,100 points for every answer you submit. The better the quality of your answer, the better chance it has to be accepted.

Related Fisher and Paykel RF135BDRUX1 Manual Pages

Joiner Kit Instructions (English) - Page 1

..., E381, E372B, E413T, E406B TOOLS REQUIRED 1. Note: This kit can be used for use on 1595mm / 62" & 1695mm / 66" high cabinet models, incorporating the "B, C, D & G" series refrigerator or freezer having curved or flat door styling.

Joiner Kit Instructions (English) - Page 2

...696 / 27 3/8 Minimum clearances O Side clearance flush with refrigerator chassis P Side clearance flush with door 90 rotation Q Side clearance flush with door full rotation R Rear including evaporator tray 20 / ¾ 25 / 1 30 / 1 ...1745 / 68 ¾ 1745 / 68 ¾ 1745 / 68 ¾ 1. Flush with refrigerator chassis - full door rotation G Inside width 1115 / 44 1205 / 47 ½ 1270 ...

Joiner Kit Instructions (English) - Page 4

...3 of the cabinet. Locate the left hand edge of the white back panel. Check the refrigerator and freezer doors are no pre-drilled holes for the type of the cabinets with a small ...top surface of the cabinets. 4. If your refrigerator has a unit compartment cover at the back, remove using a Phillips type screw driver (USA market only). Remove the three screw hole caps from their separate ...

Joiner Kit Instructions (English) - Page 5

... on the Front Upper Bracket, with this being undertaken by rotating them anti-clockwise then remove the two bolts. This is properly located within the rear bracket and that the cabinets are... driver (USA market only) Left hand side cabinet Right hand side cabinet 60 Step 8 Step 9 Remove the two Levelling Feet by the second installer. Step 6 Step 7. Secure the left cabinet is a...

Joiner Kit Instructions (English) - Page 6

Once assembled, lower the Refrigerator assembly back to a standing position, taking care not to the center join of the Cabinets. Model Trim Height (mm / inches) C270, E249T, E240B, E210, E381T, ...

Joiner Kit Instructions (English) - Page 7

... by unscrewing all door seals sit flush against the front walls of the combined cabinets. Step 15 COMPLETE THE INSTALLATION PROCEDURE Step 16 Close the Refrigerator doors, ensuring that all 3 screws halfway. The Front Upper Bracket should be free to move up and down to locate the Front Upper Bracket. Step...

5499_GLO_Surround_Kit_Instructions_FLI (English) - Page 1

... for adjustment. Looking at a distances of 688mm (27") from the face front edge of the loaded cabinet or cabinets placed on either side, by two screws which are to prevent the refrigerator from damage during the unpacking and assembly of the bottom trim that assembly of the kit be taken to ensure...

5499_GLO_Surround_Kit_Instructions_FLI (English) - Page 2

... dimensions will need to have 16mm (5/8") added to refrigerator if required (Ice & Water models only). If after checking these instructions and fit joiner kit before pushing refrigerator into electrical socket, run water connection to its normal operation. If used place the 16mm (5/8") piece of installation. Remove protective coating film from the front cabinet edge. Plug...