Home » Eureka » Vacuums » Eureka WhirlWind Plus 3279AZ

Eureka WhirlWind Plus 3279AZ Support Question

Find answers below for this question about Eureka WhirlWind Plus 3279AZ.
Need a Eureka WhirlWind Plus 3279AZ manual? We have 2 online manuals for this item!

Eureka Overview Questions Manuals Reviews Videos Research

Question posted by pattiowen on August 7th, 2013

Model 3279az Gets Hot And Shuts Off.

vacuum gets hot and shuts off. Smells like something is burning.leave it for 30 minutes and it works

I Know the Answer!

I have the same question
Request More Information

Current Answers

Answer #1: Posted by TommyKervz on August 7th, 2013 12:45 PM

TommyKervz

Member since:
January 10th, 2013

Points: 17,776,813

100
points

Greetings - This vacuum cleaner has a special thermostat that protects the vacuum in case of motor overheating (which may be owing to clogging or so). Here are its pdf resources

http://www.helpowl.com/manuals/Eureka/WhirlWindPlus3279AZ/184241

Hope that is helpful.
Kervz at www.satechhelp.co.za

Related Eureka WhirlWind Plus 3279AZ Manual Pages

Owner's Guide - Page 2

... and change light bulb. How to Clear a Blockage 5 Hose blockages. Follow caution information wherever you see this information Write the model, type and serial number here: Date of purchase (keep your Eureka vacuum cleaner. How to Use Accessories 3 Telescopic self-cleaning duster, crevice tool, extension wand, dusting brush, bare floor nozzle, turbo...

Owner's Guide - Page 3

...2886 www.eureka.com 1 If vacuum cleaner is burning or smoking, such as cigarettes, matches, or hot ashes. • Do not...be present. • Store your work area well lighted. • Unplug electrical appliances before vacuuming them. • Unplug before ...place vacuum cleaner on wet surfaces. ! • Do not leave vacuum cleaner when plugged in any time. Place vacuum cleaner ...

Owner's Guide - Page 4

...; BRUSH ROLL - dry thoroughly. until it clicks. READ ALL INSTRUCTIONS BEFORE USING THIS VACUUM CLEANER. screen inside dust cup) Dust Cup Nested Crevice Tool & Extension Wand HEPA Filter...filter and replace. Debris will empty. How to Identify Parts of Vacuum Cleaner Self-Cleaning Duster (some models) Duster Activation Lever Headlight Handle Hose Turbo Nozzle Power Switch Cord ...

Owner's Guide - Page 5

... and Extension Wand Use for furniture, drapes and vents. Grasp crevice tool and wand near ridges and pull apart. Make sure vacuum is below you, pushed against the bottom step. 1) If model has additional stair hose, attach to end of hose. 2) Attach turbo nozzle to extend. Place dusting brush on end of...

Owner's Guide - Page 6

...brush roll and belt. Make sure it slides into base (Fig. 5). Fig. 5 Change Light Bulb ! Make sure vacuum is turned off and power cord is unplugged. 1) Lower handle to lower handle flat onto floor (Fig. 1). 2)...the lens and remove old bulb. Make sure vacuum cleaner is turned off and power cord is unplugged Maintain Brush Roll Motor can become hot with bulb rated 12 v., 10 w., Type ...

Owner's Guide - Page 7

...vacuum is turned off and power cord is used by unauthorized service or the use . Clear blockage from hose retainer. Warranty is granted only to the original purchaser and members of other rights, which may not apply to you. When returning parts for repair, please include the model... option, repair or replace a defective vacuum or vacuum part that require replacement under license. ...

Owner's Guide - Page 8

...-2886. No suction at least 30 minutes before attempting to reduce suction when it to maintain suction. Dust cup and filter Hose Turbo nozzle will not turn . brush roll will not turn . Make sure vacuum is turned off and power cord is replaced into outlet, try another position. Burning smell; Problem Cause Solution Motor will...

Quick Start Guide - Page 1

...Get ready to lock. to lower handle into place. Assemble the vacuum cleaner before plugging in chamber and snap into position. Tighten two screws. Place duster in power cord. Step on some models Vacuum... chamber. Adjust height for purchasing your new Eureka vacuum! Turn duster to 7:30 p.m. (CST), Monday - Moving parts! Place crevice tool & wand ...