Eureka SuctionSeal AS1101A Support Question
Eureka SuctionSeal AS1101A Support Question
Find answers below for this question about Eureka SuctionSeal AS1101A.Need a Eureka SuctionSeal AS1101A manual? We have 2 online manuals for this item!
Question posted by Jenniferlouks on November 10th, 2013
Brush Roller Not Rotating?
the brush roller on my vacuum will not rotate. i checked the switch at the top of the vacuum and it is set to floors and i also checked the switch at the bottom and it is also set to floors so i dont know why its not rotating? i noticed the suction isnt as great when its not rotating...
Current Answers
Answer #1: Posted by BusterDoogen on November 10th, 2013 1:19 AM
BusterDoogen
Member since:
October 30th, 2011 Points: 28,565,407
Member since:
October 30th, 2011 Points: 28,565,407
Two possibilities; the brush roller motor has failed or the drive belt could be off the drive shaft or locked up due to fibers & hair that can stop the bar from rotating or is broken.
I hope this is helpful to you!
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful. Please feel free to submit further info for your question, if a solution was not provided. I appreciate the opportunity to serve you!
Related Eureka SuctionSeal AS1101A Manual Pages
Owner's Guide - Page 2
... for assembly and use accessories 3
Automatic cord rewind, brush roll lever, wand, crevice tool, dusting brush, turbo nozzle and stair hose. Inspection: Carefully unpack and inspect your vacuum cleaner 4
How to clear a blockage and maintain brush roll.
Follow caution information wherever you start your product visit www.eureka.com and click on the middle...
Owner's Guide - Page 3
... risk of fire, electric shock, or injury:
• Do not use in areas where
they may reduce airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Turn off the switch and unplug the electrical cord when not in this appliance has a polarized plug (one way. Do not use extension cords...
Owner's Guide - Page 4
...
Align tabs on back side of dust cup.
! Periodically check hose for cover to lock. Exhaust / HEPA filter EF6 ...air restriction.
Replace worn, cut or out of vacuum cleaner
Handle
SPECIAL FEATURES Available on some models
Hose
... 2
Stair hose
Crevice tool
Dusting brush
Cord rewind switch
Height adjustment knob Brush roll cover
Power switch Brush roll lever Handle release
Cord clip ...
Owner's Guide - Page 5
...
Fig. 2
FLOORS
Fig. 4 Wand 1
Wand 2 (on back of wand (Fig. 5).
• Short wand: Push hose release button to retract cord (Fig. 4). WAND 2
• Longer wand: Slide off position and put vacuum in upright position and move brush roll lever to... Turn air path selector knob to 'tools' (Fig. 3).
• When finished vacuuming, press switch to remove wand 1. Do not pull past red line (Fig.1).
Owner's Guide - Page 6
...Replace 3 screws (Fig. 6). Set air path knob to replace brush roll
• Lay vacuum with normal use. Snap hose end back up and lift off. Remove debris. Maintain brush roll
Motor pulley can become ... to maintain your vacuum cleaner
Make sure vacuum cleaner is turned off and power cord is unplugged. How to 'floors.' Pull out on floor. How to remove connector. Rotate brush roll plate up...
Owner's Guide - Page 7
... over brush and lift off cover (Fig. 1).
• Push up belt cover (Fig. 2).
• Remove old belt from wheel first, then from motor shaft (Fig. 3).
• Place new belt around motor shaft; Remove 1 screw.
• Rotate lower part of cover down over top of wheel (Fig. 4).
• Rotate wheel and belt toward vacuum front...
Owner's Guide - Page 8
... smell; Rotating brush
Vacuum height setting Belt Belt
Cord tangles
• Step on power switch to maintain suction. Brush roll will not turn off
This vacuum cleaner has a special thermostat that restrict the airflow. Make sure filter, screen and dust cup are installed properly.
• Turn selector knob to page 2 for filter maintenance. Page 4
• Check turbo nozzle...
Quick Start Guide - Page 1
...
Power switch is designed to turn brush roll lever off dust. Store dusting brush and crevice tool on some models
WAND 1
WAND 1
Turbo nozzle
WAND 2
WAND 2
Turbo cover
Vacuum cleaner
Handle...view our "How to Assemble" demo, visit www.eureka.com/suctionseal/assembly
If you assemble your vacuum
Air path knob
TOOLS
FLOORS
Pull out cord to lower handle into place. Helpline Hours: ...
Similar Questions
Turn On The Brush Roller
How do I turn on the brush roller, this was a gift and it does not spin with the vacuum on. Is there...
How do I turn on the brush roller, this was a gift and it does not spin with the vacuum on. Is there...
(Posted by Lsfish 3 years ago)
How Do I Replace Belt And Brush Roller For Eureka Quick Up 169g
How do I replace belt and brush roller on Eureka Quick Up 169G
How do I replace belt and brush roller on Eureka Quick Up 169G
(Posted by cphiller 5 years ago)
I Accidently Caught Sofa Cover In Vaccum, Now The Brush Roller Won't Start,
(Posted by bcsp15 10 years ago)
What Do I Do When It Stops Sucking To Vacuum The Floor?
(Posted by traceevarnell 10 years ago)
Brush Roller Will Not Rotate. How Can I Fix This?
(Posted by davidilaria 10 years ago)