Eureka AirSpeed Zuum AS5203A Support Question
Eureka AirSpeed Zuum AS5203A Support Question
Find answers below for this question about Eureka AirSpeed Zuum AS5203A.Need a Eureka AirSpeed Zuum AS5203A manual? We have 2 online manuals for this item!
Question posted by L69999 on April 26th, 2015
Noisy Hoover
My Airspeed Zuum seems very noisy from the bottom part of the Hoover. There doesn't appear to be anything trapped, the noise is still there after removing the cylinder, and the belt appears free and moves freely. It does seem to still suck up, but just sounds like its about to take off (as the wife describes it)Any help would be greatly appreciate
Current Answers
Answer #1: Posted by sabrie on April 26th, 2015 12:38 PM
sabrie
Member since:
May 23rd, 2013 Points: 3,306,778
Member since:
May 23rd, 2013 Points: 3,306,778
check out the video on the link below, it will give you the troubleshooting instructions.
www.techboss.co.za
Related Eureka AirSpeed Zuum AS5203A Manual Pages
Owner's Guide - Page 2
... to clear a blockage, clean brush roll, maintain brush roll, and replace U belt. Eureka Customer Service HELPLINE 1-800-282-2886
www.eureka.com
Inspection: Carefully unpack and inspect your product visit www.eureka.com and click on the underside of vacuum cleaner 2 Maintenance information 2
Dust cup and filters. Table of contents
Important safeguards...
Owner's Guide - Page 3
... airflow.
• This vacuum cleaner creates suction and contains a revolving brush roll. Turn off all parts of dust, lint,
hair, and anything that may cause damage. keep free of body away from
heated...or hot ashes.
• Do not use without dust cup and filter in place.
• Belt pulleys can become hot during normal use to a service center before unplugging.
• Do not ...
Owner's Guide - Page 4
... clicks. Moving parts! Lift latch to release screen from cyclone. HEPA filter HF16 U belt
Twist and remove collar to open cover.
Remove dust cup. Replace HEPA filter and cover.Turn to release bottom lid. Replace worn, cut or out of vacuum cleaner
Maintenance information
Handle
Clean as needed to maintain suction Replace within 6 months...
Owner's Guide - Page 5
...wand. Push crevice tool onto end of wand (Fig. 5). Make sure vacuum is in upright position to raise vacuum to highest carpet setting.
ENGLISH
TOOLS
How to use accessories
CAUTION
When ...• Pull handle to release hose (Fig. 2).
• Press power switch to turn when vacuum is turned on carpet, carpeted stairs, furniture or fringed rugs when using accessories. FLOOR
AIR PATH SELECTOR...
Owner's Guide - Page 6
.... 6).
Fig. 3
Fig. 5
• To reinstall hose, align tabs with notches and set into hose;
Twist collar to remove hair and threads from brush roll (Fig. 7). Use scissors to lock (Fig. 2). Clean brush roll
Turn vacuum face down on cover (Fig. 3).
Fig. 1
Fig. 2
• Squeeze and pull cover off and power cord is...
Owner's Guide - Page 7
...free from the date of the vacuum. You may vary by the Warranty Station. under normal use of the vacuum...Remove 4 screws from brush roll periodically. When returning parts for normal household use.
Fig. 1
Fig. 2
• Remove brush roll and belt...community You must return the vacuum or vacuum part along with normal use of brush roll to center belt.
• Replace brush ...
Owner's Guide - Page 8
... as follows: 1) Push the power switch to another setting. Vacuum is hard to 'FLOOR'
setting. Make sure filter, screen and dust cup are installed properly.
• Remove clogs from the hose that restrict the airflow. Page 3.
• Replace a worn, cut or out of shape belt. Page 3.
• Check stair and upholstery brush for...
Quick Start Guide - Page 1
... AIR PATH SELECTOR
FLOOR
TOOLS
To vacuum floors, turn air path selector to help! Plug in the carton
1 screw Extra belt
OWNER'S GUIDE
Important safeguards
2STEP
Vacuum cleaner
Dust cup
Handle
Hose with screw...
FLOOR
TOOLS
To use .
Pull handle to higher position. pull out wand. If vacuum is hard to push, adjust carpet height selector
to release hose; AS5200 Series
QUICK START ...
Similar Questions
Belt For Eureka As5203a
What is the model # of the belt used with the Eureka AS5203A?
What is the model # of the belt used with the Eureka AS5203A?
(Posted by melakian 8 years ago)
Motor Wiring Guide/assistance
I have fixed the motor previously; however this time I failed to record the location/connections for...
I have fixed the motor previously; however this time I failed to record the location/connections for...
(Posted by mbondfusion 8 years ago)
Does This Vacuum Have A Reset Button
(Posted by adenaellenreeves09 8 years ago)
I Have An Eureka Airspeed Zuum And The Brush Has Stopped Turning. How Do I Fix?
(Posted by Petulapendula 9 years ago)
Air Speed Zuum As5203a Model And Want To Know If The Filters 'hepa
will the filters, if filled with dirt, stop the vacum from starting? I haven't checked the micro swi...
will the filters, if filled with dirt, stop the vacum from starting? I haven't checked the micro swi...
(Posted by stampajoey 9 years ago)