Dewalt DWF83PL Support Question
Dewalt DWF83PL Support Question
Find answers below for this question about Dewalt DWF83PL.Need a Dewalt DWF83PL manual? We have 1 online manual for this item!
Question posted by dmoodie5223 on April 17th, 2022
Intermittant Operation
My DWF83PL only fires about half the time. I press the points hard to the work and it may or may not shoot a nail. I'm at 120 psi and using the correct Dewalt nails.Ideas? Don
Current Answers
Answer #1: Posted by Odin on April 17th, 2022 8:20 AM
Odin
Member since:
April 10th, 2010 Points: 41,236,680
Member since:
April 10th, 2010 Points: 41,236,680
Possible causes:
- Tool not receiving air
- Valve may be frozen
- Damaged or worn o-rings
- Broken or damaged driver blade
- Lack of lubrication
- Nosepiece screws loose
- Wrong size/angle fasteners
- Dirty magazine
- Damaged/Worn magazine
- Trigger valve o-ring worn or damaged
For respective fixes, see the two pages starting at https://www.manualslib.com/manual/1239455/Dewalt-Dwf83pt.html?page=15#manual
Hope this is useful. Please don't forget to click the Accept This Answer button if you do accept it. My aim is to provide reliable helpful answers, not just a lot of them. See https://www.helpowl.com/profile/Odin.
Answer #2: Posted by SonuKumar on April 17th, 2022 8:31 AM
SonuKumar
Member since:
May 9th, 2021 Points: 16,622,390
Member since:
May 9th, 2021 Points: 16,622,390
Please respond to my effort to provide you with the best possible solution by using the "Acceptable Solution" and/or the "Helpful" buttons when the answer has proven to be helpful.
Regards,
Sonu
Your search handyman for all e-support needs!!
Related Dewalt DWF83PL Manual Pages
Instruction Manual - Page 3
... ABOUT THIS OR ANY DeWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DeWALT (1-800-433-9258)
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE
Important Safety Instructions
WARNING: Do not operate this unit until you read the manual and pay attention to
exceed 120 psi, 8.3 bar) Do not connect
1 English
BEFORE OPERATING THIS TOOL, CAREFULLY READ AND UNDERSTAND...
Instruction Manual - Page 4
... is rated for a maximum working order must never exceed 200 psi even in the event of trigger and contact trip. Bottled compressed gases such as a power source for use combustible gases or any way. (Fig. F from air supply when
not in any other
reactive gas as
FIG. Do not operate a tool if any portion of...
Instruction Manual - Page 5
... aware that the tool contains fasteners.
• Do not point the tool at co-workers or yourself at any time. A protruding nail may result. (Fig. Respect the tool as a hammer....and visitors away while operating a power tool. Be sure the work material. P of any material too hard for the fastener to the Maintenance and Repairs sections for its intended use the body of injury....
Instruction Manual - Page 6
... unintentional
double fires resulting from back of its operating range, nails can result in the presence of potential harm. Q)
• Do not use tool in impact to recontact
work areas. In "Contact Actuation Mode" if contact trip is allowed to the body, especially when nailing into walls, floors or other work surface before pressing the nailer against...
Instruction Manual - Page 7
... use tool while
tired or under the influence of
FIG. 1
obstructions can result in
serious personal injury. Your risk from chemically-treated lumber. Do not use face or dust mask
C
if operation ..., alcohol, or medication.
U)
• Stay alert, watch what you
do this type of work with approved safety equipment, such as those dust masks that are :
• lead from lead...
Instruction Manual - Page 8
...
E. b. Trigger
D. Lubricate the tool following procedures and checks before each use of 12D148 ring 12D131 ring 12D131 ring
Nail Specifications
NOTE: Use only DeWALT approved fasteners. Contact trip
B. Always wear eye and ear protection when operating this manual. For safe operation, complete the following these directions: a. Use DeWALT pneumatic tool oil or a non-detergent...
Instruction Manual - Page 9
...tool from the magazine.
5.
Check for the operator to contact the work surface to actuate the trip mechanism while keeping the trigger pulled, thus driving a fastener each time the work surface before pulling the trigger. Do not use... OPERATING MODES (FIG. 1, 4, 5)
WARNING: Disconnect air line from tool and remove fasteners from trigger when not driving fasteners to avoid accidental firing....
Instruction Manual - Page 10
...
WARNING: Always know the tool operating mode before loading fasteners, to prevent a fastener from being fired during connection.
Depress the contact trip firmly against the work surface.
2. Depress the trigger. WARNING: Keep tool pointed in pivot pin (I
1. Slide the pusher (E) to drive multiple nails in the new position. WARNING: A nail will fire each time the
trigger is depressed...
Instruction Manual - Page 11
... as possible prior to exceed 120 psi) and use .
3. Actuate the tool 5 or 6 times into scrap lumber to 80 psi or less.
5. Turn pressure up to operating level (not to use tool as excessive heat can be removed. Re-lubricate with or just above and follow these instructions to shallow or deep countersink.
Cold Weather Operation
WARNING: Read the section...
Instruction Manual - Page 12
...Lubricate tool with water and mild soap. WARNING: Never use of serious personal injury, remove nails from hoses Clean magazine, pusher, and contact trip mechanism Permits smooth operation, ... frequently in reverse order. Remove magazine. Reassemble in nosepiece, have tool serviced by an authorized DeWALT service center. never immerse any adjustments or servicing this . Slide fasteners...
Instruction Manual - Page 13
... purchase. In addition to the warranty, DeWALT tools are covered by our:
1 YEAR FREE SERVICE DeWALT will allow us to contact you for your tool are not completely satisfied with the performance of injury, only DEWALT, recommended accessories should be used with this section. For products sold in locating any time during the first year after purchase...
Instruction Manual - Page 15
...
Low air pressure
Check air supply
Lack of lubrication
Lubricate tool using DeWALT pneumatic tool oil
Damaged or worn o-rings
Replace gasket/o-rings using Framing Nailer O-Ring Repair Kit
Broken or damaged driver blade Replace driver blade
Lack of tool onto a hard surface to reset the engine.
English
TROUBLESHOOTING GUIDE
MANY COMMON PROBLEMS CAN BE SOLVED EASILY...
Instruction Manual - Page 16
... blade
Replace driver blade
Nosepiece screws loose
Tighten nosepiece screws using appropriate hex wrench
Nails not feeding properly
Ensure nails are feeding properly through the magazine and into the nose
14 FOR MORE SERIOUS OR PERSISTENT PROBLEMS, CONTACT A DeWALT SERVICE CENTER OR CALL 1-(800)-4-DeWALT.
intermittent feed Air restricted
Check air supply and couplers
Lack of...
Similar Questions
Dewalt D51276k Not Firing
gun worked, then put in storage. Now it wont fire a nail. Common problems?
gun worked, then put in storage. Now it wont fire a nail. Common problems?
(Posted by RUSSELLSECHLER 2 years ago)
Dewalt Dc628 Cordless Nail Gun Won't Cite More Than One Nail
hello, I recently acquired a like new nail gun as mentioned In title. The person I got it from said ...
hello, I recently acquired a like new nail gun as mentioned In title. The person I got it from said ...
(Posted by sethmccullough 6 years ago)
Bolt Size For Dewalt 734 Planner Tool Tray
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
I need the size of the two bolts used to attach the tool tray to a 734 DeWalt Planner.
(Posted by luklyd 8 years ago)