Dell PowerEdge 2950 Support Question
Dell PowerEdge 2950 Support Question
Find answers below for this question about Dell PowerEdge 2950.Need a Dell PowerEdge 2950 manual? We have 8 online manuals for this item!
Question posted by Tladevraa on February 20th, 2014
How To Change The Raid Battery In A Poweredge 2950
The person who posted this question about this Dell product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Dell PowerEdge 2950 Manual Pages
Information Update - Page 9
...that was shipped with a "III", your system chassis is fully supported. Power 2950 II and PowerEdge 2950 III Systems
• If the front of your system chassis is labeled with ...than 4 GB of the hard drive. System Board Replacement - Safeguarding Encrypted Data
On PowerEdge 2950 III systems using Windows Server® 2008, you can use encryption programs, such as the BitLocker utility, to the...
Information Update - Page 10
... that supports
configuration has changed node interleaving. The system For memory configuration
runs but with the system.
The memory configuration Ensure that the memory
does not support node
modules are installed in a
interleaving, or the
configuration that node
for additional information
interleaving cannot be
for the PowerEdge 2950 III system and the probable...
Information Update - Page 15
... configuring system management settings, see "Getting Help" in the Hardware Owner's Manual. The LCD messages refer to maximum as a precautionary measure. For information on the PowerEdge 2950 III system and the probable cause for each message. You can change the system ID and name in the System Setup program.
Information Update - Page 16
LCD Status Messages (continued)
Code E1211
Text ROMB Batt
Causes
RAID battery is faulty.
Corrective Actions
Reseat the RAID battery connector. Remove and reseat the PCIe expansion cards.
See "... that resides in the Hardware Owner's Manual.
See the "RAID Battery" and see "Troubleshooting an Expansion Card" in the Hardware Owner's Manual. Table 1-2.
Check the AC power source...
Information Update - Page 21
... Update
21 When set to Distributed, interrupt routing is
(Standard default) swizzled to the DMA engine. Table 1-6. Changes take effect after the system reboots.
Table 1-6 lists the updated information on the default value of TCP receive
operation...operating system supports TPM. System Interrupts This field controls the interrupt assignment for the PowerEdge 2950 III system.
Information Update - Page 24
... included in the list of operating systems on the Server OS Install tab. You cannot save the file to specify the diskette drive or USB memory key where the test log file is supported by the PowerEdge 2950 and 2950 II systems, but not by the PowerEdge 2950 III system. This operating system is saved. System...
Information Update - Page 44
...; Deactivate TPM。
No Change TPM TPM TPM Security （TPM Off
TPM Clear
（TPM No [ 否 ]）
TPM 将导致 TPM TPM 密钥。
设置为 Yes TPM TPM Security （TPM Off
44
信息更新 System Security
表 1-7 PowerEdge 2950 III TPM。
TPM Security...
Information Update - Page 46
Microsoft Windows 2000
System Build and Update Utility Microsoft® Windows® 2000 将位于 Server OS Install PowerEdge 2950 和 2950 II PowerEdge 2950 III
Customize Log output file pathname USB
46
信息更新
Getting Started Guide - Page 6
...• Optional remote access controller (RAC) for an integrated SAS host bus adapter or an optional RAID controller card with 64 K colors; true-color graphics are supported in the following left riser card ... installed, the video resolution is 1600 x 1200 with 256 MB of cache memory and a RAID battery.
This video subsystem contains 16 MB of DDR SDRAM video memory (nonupgradable). OR
- The ...
Getting Started Guide - Page 13
... conditions and over the entire system ambient operating range, the inrush current may reach 55 A per power supply)
Wattage Voltage Heat dissipation Maximum inrush current
Batteries System battery RAID battery (optional)
one optional internal half height tape backup device
external optional USB
Two RJ-45 (for 10 ms or less. CR 2032 3.0-V lithium ion...
Hardware Owner's Manual (PDF) - Page 5
...the Fan Bracket 69
SAS Controller Daughter Card 69 Installing a SAS Controller Daughter Card 70 SAS and SAS RAID Controller Daughter Card Cabling Guidelines . . . . . 72 Removing a SAS Controller Daughter Card 74
RAID Battery 74 Installing a RAID Battery 74 Removing a RAID Battery 75
Configuring the Boot Device 76
Expansion Cards 76 Expansion Card Installation Guidelines 76 Installing an...
Hardware Owner's Manual (PDF) - Page 20
... Fan Redundancy
Causes
Corrective Actions
A 62-character string that can change the system ID
The SYSTEM NAME displays and name in the System only. Setup program. See "Getting Help" on page 147.
Specified voltage regulator has See "Getting Help" on page 147. RAID battery is See "Troubleshooting System out of acceptable range.
RPM...
Hardware Owner's Manual (PDF) - Page 27
... LCD.
when the temperature returns to a normal state but you might determine that the RAID Replace RAID battery. wait approximately ten seconds, reconnect the power cable, and restart the system. Table 1-6.... the status indicators and LCD colors to remove the message from the electrical outlet; See "RAID battery has less than 24 hours of events, and is a failing power supply. You can ...
Hardware Owner's Manual (PDF) - Page 51
...fans • Cooling shroud • Fan brackets • SAS controller daughter card • RAID battery • Expansion cards • Expansion card cage • RAC card • Optical, diskette, and... tape drives • System memory • Processors • System battery • Expansion-card riser boards • Sideplane board • SAS Backplane board •...
Hardware Owner's Manual (PDF) - Page 52
Inside the System
4
5
3
6
2
1
14 13
9
10 11 12
7 8
1 RAID battery (optional)
2 SAS controller daughter card 3 sideplane or SAS RAID controller daughter card (optional)
4 power supply bay
5 power supplies (2)
6 left riser
7 central riser
8 memory modules (8)
9 heatsinks and microprocessors (2)
10 hot-pluggable fans (4)
11 SAS backplane
...
Hardware Owner's Manual (PDF) - Page 74
... daughter card on top of the hard drive bays. 3 Insert the battery carrier and RAID battery into the battery carrier. See Figure 3-12. RAID Battery
Installing a RAID Battery
1 Insert the RAID battery into the chassis battery carrier slots and connect the battery
cable to the storage daughter card, ensuring that the battery carrier is aligned and fully seated in its tray away
from...
Hardware Owner's Manual (PDF) - Page 75
Figure 3-17. Installing a RAID Battery 3 4
2
1
1 chassis battery carrier slot (2) 2 battery cable
4 SAS RAID controller daughter card battery
3 battery carrier
Removing a RAID Battery
1 Disconnect the cable between the RAID battery and the SAS RAID controller daughter card.
Installing System Components
75 See Figure 3-17.
2 Press down and to the left on the battery carrier to disengage...
Hardware Owner's Manual (PDF) - Page 127
... or remove the bezel. Problem • Error message indicates a problem with an expansion card. • Expansion card performs incorrectly or not at all. See
"Installing a RAID Battery" on the system and attached peripherals. 9 If you have a SAS controller daughter card, see your operating system and the expansion card. See "Opening and Closing...
Hardware Owner's Manual (PDF) - Page 178
... drive blank, 57 hard drives, 57 left riser board, 98 memory, 90 memory guidelines, 89 optical drive, 82 power supply blank, 65 processor, 93, 95 RAID battery, 74
installing (continued) SAS backplane board, 104 SAS controller daughter card, 70 SAS hard drive in a SATAu drive carrier, 59 SATA hard drive in a SATA...
Hardware Owner's Manual (PDF) - Page 179
... hard drives, 57 left riser, 99 left riser board, 98 memory, 92 optical drive, 81 power supply, 63 power supply blank, 64 processor, 93, 95 RAID battery, 75 SAS backplane board, 103 SAS controller daughter card, 69, 74 sideplane board, 101 system board, 107 tape drive, 86 tape drive cable retention bracket...
