Dell PowerConnect 6224 Support Question
Dell PowerConnect 6224 Support Question
Find answers below for this question about Dell PowerConnect 6224.Need a Dell PowerConnect 6224 manual? We have 5 online manuals for this item!
Question posted by jakesambla on December 25th, 2013
What Information Are Needed To Initially Configure A Powerconnect 6200 Series
switch with easy setup wizard
Current Answers
Related Dell PowerConnect 6224 Manual Pages
Command Line Interface Guide - Page 154
... or exit command. Starting the CLI
To begin running the CLI, perform the following configuration on the console line only.
The wizard configures one privileged user account during the setup.
Easy Setup Wizard
The Easy Setup Wizard guides the user in the basic initial configuration of a newly installed switch so that it can be managed over a direct connection to add users later. The...
Command Line Interface Guide - Page 158
...also choose to allow all IP addresses to configure the initial values as defined above . After the switch completes the POST and is configured. SNMPv3 is disabled.
• The ... or default gateway. After the user completes the wizard, the system is configured as defined above .
Example Session
This section describes an Easy Setup Wizard session. NOTE: In the example, the possible user...
Command Line Interface Guide - Page 159
... can use Dell Network Manager or other SNMP accounts. (For more information on setting up and running as quickly as possible. You can skip the setup wizard, and enter CLI mode to manually configure the switch.
Welcome to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you up an SNMP version 1 or 3 account, see the...
Command Line Interface Guide - Page 162
... as quickly as possible.
For more information on setting up the initial SNMP version 2 account now.
. Set up user accounts and changing privilege levels, see the user documentation).
Welcome to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you like to run the setup wizard within 60 seconds)? [Y/N] y
Step 1:
The system...
User's Guide - Page 5
... Port LEDs 64 SFP+ Port LEDs 65 XFP Module Port LEDs 65 10/100/1000 Base-T Port LEDs 65 System LEDs 67 Stacking LEDs 68
5 Configuring Dell PowerConnect
Overview 71 Starting the CLI 72 General Configuration Information 74
Terminal Connection Configuration 74 Baud Rate 74 Other Configuration Requirements 74 Booting the Switch 75 Configuration Overview 81 Easy Setup Wizard 81
5
User's Guide - Page 81
... up .
The Easy Setup Wizard guides you in this section).
• IP subnet mask for the network
• Default gateway (next hop router) IP address for configuring the default route
There are two types of configuration: • Initial configuration consists of a newly installed switch so that the initial administrator account be saved before rebooting. Configuring Dell PowerConnect
81...
User's Guide - Page 82
...are allowed in the community string, their use the wizard initially, the session defaults to the factory-default settings. The wizard requires the use of quotation marks when you do... the switch has not yet been configured. If it is configured, the default access level is set -up wizard continues to the highest available access for the Easy Setup Wizard.
82
Configuring Dell PowerConnect The ...
User's Guide - Page 84
... choosing the (0.0.0.0) IP address. • An IP address is 192.168.1.1. • The SNMP community string to Dell Easy Setup Wizard
The Setup Wizard guides you through the initial switch configuration, and gets you complete the wizard, the system is configured as follows: • SNMPv1/2c is enabled and the community string is set up and running an example Dell...
User's Guide - Page 86
... which this requires that the system automatically retrieve an IP address from which all ports are members. This is correct, please select (Y) to save the configuration, and copy to access the CLI, Web interface, or SNMP interface for using the Dell Easy Setup Wizard. If the information is setup. You will now enter CLI mode. .....
Getting Started Guide - Page 14
...received it. • The PowerConnect switch booted successfully. • The console connection was established and the Dell Easy Setup Wizard prompt appears on the screen
of a VT100 terminal or terminal equivalent. The wizard configures one privileged user account during the initial configuration. The initial switch configuration is empty. After the initial configuration, you to specify the...
Getting Started Guide - Page 16
... SNMP management account you can create additional user accounts after completing the Easy Setup Wizard. The wizard automatically assigns the highest access level [Privilege Level 15] to this setting and to configure your initial privilege (Level 15) user account. You may set up an SNMP version 3 account, see the User's Guide.
NOTE: You can :
o Set up...
Getting Started Guide - Page 63
...10
Krok 2:
Now we need to access the switch. For more information on setting up user ...the particular management system uses to configure your initial privilege (Level 15) user ...information on adding management systems, see the User's Guide. POZNÁMKA: Další uživatelské účty můžete vytvořit i po dokončení průvodce Easy Setup Wizard...
Getting Started Guide - Page 86
... celles qui sont indiquées ci-dessus.
Would you like to Dell Easy Setup Wizard
The setup wizard guides you through the initial switch configuration, and gets you up an SNMP version 3 account, see the User's Guide.
84
Guide de mise en route For more information on adding management systems, see the user documentation). You can exit the...
Getting Started Guide - Page 136
...information on setting up other management interfaces to change this setting and to manually configure the switch. To manage the switch using the default system configuration. Would you like to access the switch... string to Dell Easy Setup Wizard
The setup wizard guides you through the initial switch configuration, and gets you can exit the setup wizard at any point by default.
Getting Started Guide - Page 160
... | support.dell.com
Enter Dell Easy Setup Wizard POST Welcome to Dell Easy Setup Wizard
The setup wizard guides you through the initial switch configuration, and gets you up and running as quickly as possible.You can skip the setup wizard, and enter CLI mode to manually configure the switch.You must respond to the next question to run the setup wizard (you must answer this account...
Getting Started Guide - Page 161
...Easy Setup Wizard 3： Next, an IP address is set up.The IP address is the IP address you use to the CLI and Web interface.You may set up user accounts and changing privilege levels, see the User's Guide.
To set up other accounts and change privilege levels later.For more information...25163;順 2： Now we need to configure your initial privilege (Level 15) user account.This ...
Getting Started Guide - Page 185
... need to the CLI and Web interface. This account is used to login to configure your initial ...privilege (Level 15) user account. To set up a user account:
Please enter the user name {admin}: admin
Please enter the user password: ********
Please reenter the user password: ******** You may set up other accounts and change privilege levels later.
For more information...
Getting Started Guide - Page 208
... 2:
Now we need to be used to login to access the switch.
To set up user accounts and changing privilege levels, see the User's Guide.
Zapoznaj się z Podręcznikiem użytkownika w celu uzyskania dalszych informacji.
206
Instrukcja uruchomienia UWAGA: Po zakończeniu instalacji za pomocą kreatora Easy Setup Wizard moż...
Getting Started Guide - Page 231
...setup wizard, and enter CLI mode to manually configure the switch.
You can use Dell Open Manage Network Manager or other SNMP accounts. (For more information on setting up and running as quickly as possible. o Return later and set up the initial... siguiente:
Welcome to Dell Easy Setup Wizard
The setup wizard guides you through the initial switch configuration, and gets you must answer...
Getting Started Guide - Page 232
...the gateway from any Management Station {0.0.0.0}: 192.168.1.10
Paso 2: Now we need to configure your initial privilege (Level 15) user account.
The IP address is reachable (e.g. 192... SNMP interface for the switch. NOTA: cuando finalice Easy Setup Wizard (Asistente para configuración fácil) podrá crear cuentas de usuario adicionales. For more information on the default VLAN ...
Similar Questions
How To Configure Powerconnect 6224, 5324 & 5424 Switches Pdf
(Posted by garpdb19 9 years ago)
How To Configure Powerconnect 6224 With Serial Port
(Posted by jerovac 9 years ago)
How To Run The Dell Easy Setup Wizard Session For Powerconnect 6224
(Posted by mikeatc3 9 years ago)
Dell Powerconnect 6248 Switch How To Start Easy Setup Wizard
(Posted by mar2ah 10 years ago)