Craftsman 79194 Support Question
Craftsman 79194 Support Question
Find answers below for this question about Craftsman 79194 - 29cc 4 Cycle Gas Trimmer.Need a Craftsman 79194 manual? We have 1 online manual for this item!
Question posted by wkbrkeit on August 1st, 2014
Craftsman 4 Cycle Weedwacker Stopped And Will Not Start Cylinder Head
The person who posted this question about this Craftsman product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Craftsman 79194 Manual Pages
Operation Manual - Page 1
Operator's Manual
®
4-Cycle
WEEDWACKER® GAS TRIMMER
Model No. 316.791940
INCREDI.PULL TM
RNGEL/EVABLS
STARTING
EA SE
with MAXFIRE@IGNITION
_
CAUTION: Before using this product, read this manual and follow all
safety rules and operating instructions.
• SAFETY • ASSEMBLY &#...
Operation Manual - Page 2
...start the engine until fuel vapors dissipate.
• Move the unit at least 30 feet (9.1 m) from the unit immediately.
• Avoid creating a source of injury to the head... attention and understanding.
FUEL SAFETY WARNINGS FOR GAS UNITS
• Read the instructions carefully. ...
Oil and Fuel Information
6
Starting/Stopping Instructions
7
Operating Instructions
8
Maintenance...
Operation Manual - Page 3
...trimmer.
May
be hazardous, and will also void your size in conjunction with loose or damaged parts.
• Stop...starting. Breathinegxhausfut mescanbefatal.Operattehisunitonlyina well-ventilatoeudtdooarrea. • WeasrafetgylasseosrgogglethsatmeeAt NSZI87.1-1989 standards
and are distributed by Sears or a Craftsman...8226; Allow the engine to Starting/Stopping Instructions.
• Use the...
Operation Manual - Page 4
Thiswarrantayppliefsoronly90daysifthisproducist everusedforcommercioarlrentapl urposes. Your new Craftsman® product is designed and manufactured for parts and labor on all covered repairs [] Product replacement up to $1500 if your Repair Protection Agreement today! ...
Operation Manual - Page 5
On/Off Stop Control
Shaft Housing
(4) Screws
Shaft Grip
Minimum 6 (15.24 cm)
D-Handle
Fig. 1
Bottom Clamp
2....Muffler
Spark Plug
Oil Fill Plug
Shaft Grip On/Off Sto
Control
D-Handle
Craftsman® Convertible TM
Coupler
Shaft Housing
Trimmer Attachment
Fuel Cap
Starter Rope Grip
Cold
Starting Lever
Throttle Control
Line
Cutting Blade
Air Filter Primer
Cover
Bulb
_Att
acCutt ...
Operation Manual - Page 6
...and reinstall the oil fill plug. Always stop the engine and allow it to the...forming harmful deposits in the crankcase before starting the engine.
In order to avoid ... absorbs water.
epmNlaeocvveee.r foupeel rcaatep sthloewulynittowiathvoouidt inthjueryfuel
Gas Can Spout
Fuel Tank Fig. 6
Fuel Cap...shipped without oil. NOTE: This is a four cycle engine. Avoid creating a source of SAE 30 ...
Operation Manual - Page 7
...) what you are squeezing the throttle, go back to 60 seconds. Press and hold On/Off Stop Control in the OFF (O) position until you can see fuel in the starting method is no need to a complete stop (Fig. 9). Fully press and release the primer bulb 10 times, slowly. With the unit in it...
Operation Manual - Page 8
... Cutting from the knob (Fig. 16). where vegetation is securely tightened. Fig. 11
USING THE CRAFTSMAN@ CONVERTIBLE TM FEATURE
I WinsAtaRllNinIgNGa:ttacTh°meanvtosi.d seri°us pers°na' inj ury ... the coupler (Fig. 14).
90 ° Edging Hole (Trimmer ®hi
Knob Fig. 12
Craftsman® Convertible TM Coupler
Primary Hole Release Button
Knob Fig. 13
Guide Recess
Upper _n...
Operation Manual - Page 9
...
Always WseArvRicNeINaGn:d reTpoairpraevceonotl suenritio.
NOTE: Some maintenance procedures may be required. FREQUENCY
Before starting engine
Every 10 hours 1st change at 10 hours At 25 hours/every 25 hours...shown on the cutting head. LINEREPLACEMENT
for Hassle-Free TM Cutting Head
I
oruCtchdamageOtVherThheuant.imt.osay ead to serous persona n ury
Always use Craftsman® Hassle-Free ...
Operation Manual - Page 10
... Stop the...fill hole and into a container by tipping the unit to prevent accidental starting.
2. Pour the oil out of oil to get a proper oil ...any oil residue on an elevated, level surface with the cutting
head shield hanging off the surface to the oil fill hole and... Oil Fill Line / Fig. 19
Fig. 20
\\
Fill Level
L
4-Cycle
Motor Oil
Fig. 22 6. see Checking the Oil Level. Replace the oil...
Operation Manual - Page 11
...the engine will not idle, adjust the idle speed screw as needed ), until the attachment stops turning. Refer to Starting/Stopping Instructions.
2. Refer to Air Filter Maintenance.
3.
Remove the air filter (Fig. 23...Air _
Fig. 26
Tabs
Fig. 27
Locking Tab
sure the cutting attachment has stopped rotating before adjusting the idle speed screw. Clean Air Filter
The condition of a turn...
Operation Manual - Page 12
....
12. Check alignment of each valve stem.
Stop the engine and allow it to view the piston (Fig. 32). Remove the spark plug from the cylinder head by turning a 5/8 in. If these statements ...clearance with a feeler gauge after every 25 hours of its condition.
1. Remove the spark plug from the cylinder head by turning a 5/8 in. Turn the adjusting nut using a 5/16 inch (8 mm) wrench or nut...
Operation Manual - Page 13
...has been drained from the cylinder before storing. • Lock up the unit to start the trimmer after storage.
4. NOTE: ... container. Remove the spark arrestor screen from the gas tank into the cylinder. Clean the spark arrestor screen with fuel in ...not use or damage. • Store the unit in the cylinder head. Household cleaners that has been stored for any moisture with ...
Operation Manual - Page 14
... or replace spark arrestor
ACTION Replace or clean the air filter Adjust idle speed
ACTION Drain gas tank and add fresh fuel
Plugged spark arrestor
Clean or replace spark arrestor
CAUSE Old fuel
ACTION Drain gas tank and add fresh fuel
Fouled spark plug
Replace or clean the spark plug
NOTE: For...
Operation Manual - Page 15
...Ibs (5.2-5.9 kg)
Cutting Mechanism ... HassleFree TM Head
Timming Line ... CALIFORNIA / EPA EMISSION CONTROL ...are based on your operator's manual. Steel Tube (Craftsman® Convertible TM)
Throttle Control ...
Where a...Housing ...
EnginTeype...A..i.r.-.C...o..o..l.e.4.d.-.,C...y..c..le........
Incredi-Pull TM Starting Auto Rewind
Muffler ...
The manufacturer is defective...
Operation Manual - Page 16
...part must be repaired or replaced by Sears. The displacement of your small off -road Lawn & Garden engine owner, you should contact Sears at a warranty station.
(7) Throughout the evaporative ... you have a question regarding your warranty coverage, you are responsible for presenting your Lawn & Garden fuel tank to the first scheduled replacement point for that is performed at 1-800-4-MY...
Operation Manual - Page 34
REPLACEMENT PARTS - MODEL 316.791940 4-CYCLE GAS TRIMMER
Item 1 2 3 4
5 6 7 8 9 10
11 12 13
14 15 16 ...Description Engine Cover Assembly Cover Screw Screw Rocker Cover
(includes
2 & 3)
Rocker Cover O-Ring
Cylinder Assembly (includes 3, 5 & 9) Piston Ring Assembly
Piston Assembly (includes 7) Cylinder O-Ring Breather Hose
Oil Plug (includes 12) Oil Plug O-Ring Crankcase Cover
Crankcase Cover O-...
Operation Manual - Page 35
MODEL 316.791940 4-CYCLE GAS TRIMMER
Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
Pa_ No. 753-04234 753-04119... Shaft Shield Mount Hardware
Blade Assembly Shield Assembly (includes 19) Lower Clamp Assembly (includes 22) Anti-Rotation Screw
Bushing Housing Assembly Adapter Cutting Head Assembly Glide Plate Tube of Precut Line
Items Not Shown
E19 REPLACEMENT PARTS -
Operation Manual - Page 36
...www.managemyhome.com
For repair- For Sears professional installation of home appliances and items like vacuums, lawn equipment, and electronics, call anytime for the location of your home- of carry-in your nearest...www.sears.com
www.sears.ca
Our Home
For repair of all major brand appliances, lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who ...
Similar Questions
Repair Of Rope Pull On Craftsman 316.791940 29cc 4 Cycle Gas Trimmer
Rope pull pulls but don't "catch" to rotate shaft. It retracts fine.
Rope pull pulls but don't "catch" to rotate shaft. It retracts fine.
(Posted by belldon10 7 years ago)
Replacing Head On A Craftsman Gas Trimmer
How do you remove the head from a 29cc 4 cycle curved shaft 8-1 attachment gas trimmer? I want to pu...
How do you remove the head from a 29cc 4 cycle curved shaft 8-1 attachment gas trimmer? I want to pu...
(Posted by pollieut 9 years ago)
How To Add Oil To Craftsman 4 Cycle Gas Trimmer
(Posted by yeJAH99 9 years ago)
How To Replace String On Craftsman 29cc 4 Cycle Gas Trimmer
(Posted by johlvbec 10 years ago)
29cc 4 Cy Gas Trimmer
(Posted by royerton 11 years ago)