Craftsman 28790 Support Question
Craftsman 28790 Support Question
Find answers below for this question about Craftsman 28790 - 26 HP 50 in. Zero Turn Tractor Mower.Need a Craftsman 28790 manual? We have 1 online manual for this item!
Question posted by mrBigBe on August 18th, 2014
How Do I Adjust The Ground Travel On A Craftsman Zero Turn Mower
The person who posted this question about this Craftsman product did not include a detailed explanation. Please use the "Request More Information" button to the right if more details would help you to answer this question.
Current Answers
Related Craftsman 28790 Manual Pages
Operation Manual - Page 1
Operator's Manual
ZTS 7500
Zero-Turn Rear Engine Rider with Electric Start
Model No. 107.28790 (26 HP Briggs & Stratton Engine with 50" Mower)
CAUTION: Before using this
Nota: Una traducci6n en espaSol de este Manual del Operador puede encontrarse en la pagina 33.
Sears, Roebuck and Co., Hoffman ...
Operation Manual - Page 3
..., to cool before and while
travelling in an enclosed poorly ventilated structure... equipped), disengage the blades (PTO), stop before turning. 11. Disengage attachments before starting.
2. Do ... refueling, removing an attachment, making adjustments (unless the adjustment can restrict operator age).
4. Allow... a positive mechanical lock is used.
26. Data indicates that the blades and blade...
Operation Manual - Page 4
...and drive slow off if children enter the area. 3. The mower could suddenly turn unit off the slope. 6. Do not turn slowly and gradually uphill, if posstble. Follow the manufacturer's recommendations... hide obstacles. 3. Never mow down the face of the ground conditions, incorrect hitching and load distribution.
1. Travel slowly and allow children to operate the unit. 6. Use ...
Operation Manual - Page 6
... by an authorized techntcian.
26. If the fuel tank ...pressure. Repair, if necessary, before storage. 5. Adjust and service as necessary. 11. Improper
service procedures...where carbon
monoxide fumes may ignite. Mower blades are explosive. 12. Never ... it is spilled on the ground away from pin holes or...
hydro pump cooling fan, when the tractor is not possible, then refuel such...
Operation Manual - Page 10
...ground speed and parking brake of individual controls. Pulling back on the mower blades with the engine speed set to FAST. Move the engine speed control back to SLOW to OPEN (push the knob down ). Only turn on the mower... use for steering instructions.
_
Engine Speed Control
The engine speed control adjusts engine speed.
Pulling the levers in across the operator's lap puts the...
Operation Manual - Page 12
...volume) are approved.
Do not allow passengers to a maximum of this zero-turn rider on a trailer or truck using ethanol or methanol) can damage ... ramps. Fill the tank. Do not overfill. Select slow ground speed before storage of 30 days or longer. Do not ...with care. To reduce fire hazard, keep the engine, rider and mower free of slopes, not across. Install and hand tighten the fuel...
Operation Manual - Page 13
... stop rider movement and engage the parking brake.
2. Locate the transmission release levers (C, Figure 3) at least a minute before turning on a slope.
1. Pull the ground speed control levers in STOPPING THE RIDER AND ENGINE. Turn the mower blades ON (pull switch up).
5. See DRIVING PRACTICE.
8. Transmission Release Levers A. Push Position C.Transmission Release Levers
13 While...
Operation Manual - Page 14
... are very responsive, and learning to getting the most out of the zero turn units on slopes greater than 17.6% (10°). Move Control Levers Gradually
Forward Travel Practice
Gradually move both ground speed control levers evenly FORWARD from other fourwheeled vehicles. Operating zero turn rider. We suggest you will take some time going forward, and...
Operation Manual - Page 15
... and experienced with operating the zero turn rider, you will learn more you to turn in place, gradually move one ground speed control lever forward from ...turns the rider RIGHT and slightly overlaps the row just cut missed grass. Practice Turning In Place
To "zero turn" means to back up and re-cut --eliminating the need to turn :
1.
Practice Turning Around a Corner
While traveling...
Operation Manual - Page 16
... without
starting the engine. 5. WARNING
After lowering the mower cutting height, engage parking brake, turn off the mower blades, turn the ignition OFF, and wait for all moving parts to install or remove the mower. Remove the retainer and hitch rod (C). 11. Turn the mower blades OFF, put the ground speed control levers in Figure 11.
16 Place...
Operation Manual - Page 18
... A.
Note that these pressures may differ slightly from the "Max Inflation" stamped on the back edge of the tires. Rider Maintenance Items
WARNING
Move the ground speed levers to START/PARK positions, turn the mower blades OFF, turn the ignition switch OFF, and wait for all moving parts to access the engine compartment.
Operation Manual - Page 21
...
The mower blades and mower drive belt should you attempt to start the engine.
NOTE: Once the engine has stopped, the mower blade switch must be turned OFF and the ground speed ...water.
4. Operational SAFETY Checks TEST 1 -- ENGINE SHOULD NOT CRANK IF:
• Mower blades switch is turned OFE If mower drive belt does not stop within five seconds, contact a Sears Parts & Repair Center...
Operation Manual - Page 22
... ignition switch and disconnect spark plug wires to dimensional variations on level ground. Figure 24. Note the position of accidental starting while the PTO is inserted and removed, and make any necessary adjustments by the mower blade switch.
Alternately tighten the adjustment nuts (B, Figure 25) until the rotor face and armature face just contacts...
Operation Manual - Page 26
... jam nut when complete. Mower cutting height range is located on the opposite side. Tighten the jam nut (A) to 1-1/2". Loosen the jam nut and turn the knob COUNTERCLOCKWISE to increase speed or CLOCKWISE to the desired position. Cutting Height Adjustment A. Tighten the mounting bolts.(D).
Forward Slot D.
Repeat with the other ground speed lever.
\
Figure...
Operation Manual - Page 27
... cause of a defect in their PARK positions should be performed by turning the adjustment nut (B), if necessary. Return Spring (Removed for all operating conditions. Adjust the spring length by a Sears or other electrical component. BRAKE ADJUSTMENT
1. Stop the unit, turn the ignition OFE set the ground speed levers to stop.
2. Measure the parking brake spring (E).
Always...
Operation Manual - Page 28
.... Side to Side Leveling
If the cut .
Turn the engine off, set the ground speed control levers to PARK, and wait for bent blades and replace if necessary.
3. See Figure 37. Orient Blades Side-to Ground
Figure 36. MOWER DECK LEVELING ADJUSTMENTS
\
WARNING
Before adjusting the mower, turn the mower blades OFF, turn the ignition switch OFF, remove the key...
Operation Manual - Page 29
...38). Rear Jam Nut C. Disengage the PTO,
turn off the engine and set the ground speed control levers to release belt tension and remove the mower drive belt (F) from the remaining deck pulleys. ... -back leveling. The front mower hitch rod (A, Figure 39) is uneven, the mower may also cause an uneven cut is used to adjust front-to adjust the deck level. Adjust the front jam nuts (C) on...
Operation Manual - Page 30
...of acids during storage. Acidic gas can travel to prevent gum deposits from the ignition ...Displacement Electrical System Oil Capacity
Briggs & Stratton Intek
26 @ 3600 rpm* 44.2 Cu. Check all ...Axle
Hydro-Gear EZT ZC-AHBB-2A7B-1DPX 20w 50 Premium Engine Oil 115 ft-lbs
340 Ibs
CHASSIS... the following steps:
• Turn the mower blades OFF, set the ground speed control levers to START /...
Operation Manual - Page 32
Drive belt slips. Pulleys or belt greasy or oily. Replace belt.
Rider tracks to adjust. Ground speed adj. Troubleshooting PROBLEM Mower cutting height difficult to one side. Rider tires not inflated equally or properly.
Always set throttle to arbors. Decrease ground speed. See Maintenance Section. Blades not properly fastened to FULL when mowing. Cut tall...
Operation Manual - Page 85
... Instructions Upper (English/French) DECAL Operator Instructions Lower (English/French) DECAL Tracking Adjustment DECAL ZTS 7500 26/50
DECAL Height of Cut LITERATURE PACK, SEARS ZTS 7500 26/50 (Not Shown) DECAL, Craftsman Logo DECAL, Caution Cut Hazard DECAL, Hot Surfaces
ZTS 7500-107.28790
Footnotes Note * Not a servicible part. DECAL Instrument Panel DECAL Height of Cut...
Similar Questions
What Size Oil Filter Do It Need For My Zero Turn
(Posted by Anonymous-134248 10 years ago)
Craftsman Mod. 944.609312
Were can i get a parts and service manuals for a Craftsman 26 hp 54" cut Mod.
Were can i get a parts and service manuals for a Craftsman 26 hp 54" cut Mod.
(Posted by bhookings 10 years ago)
I Have A Zts 7500 Els Lawn Mower
Where can I find a correct diagram of the belt replacement? Mine came off and the one on the manual ...
Where can I find a correct diagram of the belt replacement? Mine came off and the one on the manual ...
(Posted by sherryf1961 10 years ago)
How Do I Disengage The Transmissions So I Can Move A Dead Mower?
(Posted by vrodhowie 11 years ago)
Craftsman Zts 7500 Steering Adjustment
I have the Craftsman ZTS 7500 with a 27 hp Kohler engine purchased 3 wks ago in May 2012. With both ...
I have the Craftsman ZTS 7500 with a 27 hp Kohler engine purchased 3 wks ago in May 2012. With both ...
(Posted by gettystw 11 years ago)